Slump Cone Set for Material Testing Laboratories in Malaysia
Slump Cone Set for Material Testing Laboratories in Malaysia
Introduction
Material testing laboratories require reliable and practical equipment for concrete testing work.
Some laboratories perform most of their testing inside a permanent laboratory facility, while others also send technicians to construction sites, ready-mix plants, precast factories, and infrastructure projects.
For fresh concrete testing, the Slump Cone Set is one of the compact pieces of equipment that a laboratory may need for routine testing, site work, training, or project support.
Unlike large testing machines that normally remain permanently installed, a Slump Cone Set is relatively easy to store and transport. This makes it useful for both laboratory-based and mobile testing teams.
At MTM Precision Sdn. Bhd., our standard Slump Cone Complete Set consists of:
Slump Cone – 1.5mm thickness
Base Plate – 40 × 40cm
Slump Measuring Scale / Measuring Frame
Tamping Rod – 50cm standard
For laboratories requiring a longer Tamping Rod, a 60cm version is available as an optional selection at additional cost.
This configuration is suitable for material testing laboratories, construction laboratories, ready-mix QC departments, contractors, precast manufacturers, universities, and other concrete testing applications throughout Malaysia.
Why Material Testing Laboratories Need Slump Cone Equipment
Concrete testing laboratories may receive work from many different customers.
These can include:
Building contractors
Civil engineering contractors
Ready-mix concrete companies
Precast manufacturers
Developers
Consultants
Government projects
Universities
Research organisations
Depending on the scope of work, laboratory technicians may need to perform fresh concrete testing either inside the laboratory environment or directly at the customer's site.
A portable Slump Cone Set allows the laboratory to support both types of work.
Laboratory Testing and Site Testing Are Different
A permanent laboratory normally has organised:
Working areas
Storage
Testing equipment
Cleaning facilities
Controlled equipment records
Site testing can be very different.
The technician may need to travel to a construction project and carry the required equipment in a vehicle.
This means equipment should be prepared before leaving the laboratory.
If one component is missing, the technician may only discover the problem after reaching the project.
Keep a Complete Slump Cone Set for Mobile Testing
For laboratories performing external site work, it can be practical to maintain one or more complete sets specifically for mobile technicians.
Instead of removing individual items from the main laboratory every time, a mobile set can remain ready for site assignments.
A complete MTM Precision set contains four main items.
Slump Cone – 1.5mm Thickness
The main Slump Cone supplied by MTM Precision has a stated thickness of:
1.5mm
For laboratories purchasing testing equipment, clearly stated specifications are useful because the purchasing department may receive quotations for products that look similar but are not necessarily constructed the same way.
The actual product specification should therefore be reviewed together with the applicable testing requirement.
Base Plate – 40 × 40cm
The standard package includes:
40 × 40cm Base Plate
For a permanent laboratory, the Base Plate can be stored together with the Slump Cone in the designated concrete testing area.
For mobile technicians, it can travel with the complete set to the construction site.
This helps prevent technicians from depending on whatever working surface happens to be available at the project.
Slump Measuring Scale / Measuring Frame
The standard set also includes:
Slump Measuring Scale / Measuring Frame
This should remain together with the Slump Cone equipment.
Laboratories frequently control many small pieces of testing equipment, and accessories can easily become separated if there is no clear storage system.
Keeping the complete set together makes equipment preparation easier.
Tamping Rod – 50cm Standard
The standard MTM Precision package includes a:
50cm Tamping Rod
For routine ordering, laboratories can use this as the standard package where it matches their requirement.
Optional 60cm Tamping Rod
For customers requiring a longer version:
60cm Tamping Rod is available as an optional selection.
The 60cm version carries an additional charge.
Laboratories should therefore confirm the required rod length before ordering.
If different test requirements are handled by the same laboratory, it may also be useful to identify the different Tamping Rods clearly.
How Many Slump Cone Sets Does a Laboratory Need?
The correct quantity depends on workload.
A small laboratory with one concrete testing technician may require only a limited number of sets.
A larger laboratory may have several technicians performing:
Laboratory work
Construction-site testing
Ready-mix plant testing
Precast factory testing
at the same time.
In this situation, one Slump Cone Set may not be enough.
Calculate by Active Testing Team
Instead of buying equipment based only on laboratory size, consider how many teams may need it simultaneously.
For example:
LABORATORY
1 × Slump Cone Set
MOBILE TEAM 1
1 × Slump Cone Set
MOBILE TEAM 2
1 × Slump Cone Set
SPARE
1 × Slump Cone Set
The laboratory in this example may maintain four complete sets.
Actual quantities should follow the laboratory's workload and technical requirements.
Don't Make Every Technician Share One Set
Sharing equipment can work when testing schedules do not overlap.
The problem appears when two technicians receive site assignments for the same morning.
Technician A needs the Slump Cone Set for one construction project.
Technician B needs the same equipment for another customer.
Now one of them cannot take the equipment.
Where workload justifies it, dedicated mobile sets can make scheduling easier.
Prepare a Mobile Concrete Testing Kit
A laboratory vehicle can carry the compact equipment required for the planned site work.
Depending on the testing scope, this may include:
Slump Cone Complete Set
Concrete Cube Moulds
Measuring Equipment
PPE
Documentation
Other required testing equipment
The exact equipment should follow the work order and applicable test requirements.
Slump Cone and Concrete Cube Moulds
Material testing laboratories are also an important customer group for Concrete Cube Moulds.
The Slump Cone and Cube Mould serve different purposes, but they can both be required as part of concrete testing activities.
For this reason, laboratories purchasing new Slump Cone equipment can also review their Cube Mould inventory.
Plastic Cube Moulds for Mobile Laboratory Teams
When technicians need to transport several Cube Moulds to a site, Plastic Concrete Cube Moulds can be practical because they are relatively lightweight and corrosion resistant.
A mobile team may therefore carry:
1 Slump Cone Complete Set
plus
Several Plastic Cube Moulds
depending on the required sampling programme.
The lower weight can become noticeable when technicians repeatedly load and unload equipment from a vehicle.
Cast Iron Cube Moulds for Laboratory Use
For permanent laboratory operations, customers may also consider Cast Iron Concrete Cube Moulds where suitable for their requirements.
Because these moulds are heavier, they may be more convenient in a fixed testing environment than for technicians who need to carry many units around a construction site.
The appropriate choice should follow the laboratory's required standard, procedure, and working method.
Separate Laboratory Sets from Mobile Sets
A useful equipment-management approach is to identify:
LAB USE
and
SITE USE
separately.
For example:
LAB-SC01
Permanent laboratory Slump Cone Set
SITE-SC01
Mobile Testing Team 1
SITE-SC02
Mobile Testing Team 2
This reduces the chance that the permanent laboratory set disappears because somebody took it to a site.
Label All Four Components
Labelling only the Slump Cone may not be enough.
The Base Plate, Measuring Scale, and Tamping Rod can also move between testing teams.
Where practical, use the same equipment identification for the complete set.
For example:
SITE-SC02
on all related components.
This makes it easier to rebuild the correct set after cleaning or storage.
Check Equipment Before Leaving for Site
Before a technician departs, confirm:
Slump Cone available?
Base Plate available?
Measuring Scale available?
Tamping Rod available?
Correct Tamping Rod length?
Cube Mould quantity sufficient?
Other required equipment ready?
A short check at the laboratory can prevent a wasted trip.
Return Equipment as a Complete Set
After site testing, the technician should return all equipment.
A useful process is:
Return → Clean → Inspect → Record → Store
If one component is missing, identify the problem immediately.
Do not wait until the next technician needs the equipment.
Equipment Condition Should Be Checked
Laboratories normally place greater emphasis on equipment control than general construction stores.
The Slump Cone Set should therefore be inspected according to the laboratory's applicable QA/QC system.
If equipment becomes damaged or unsuitable, the responsible technical personnel should determine the appropriate action.
Replacement should be arranged where necessary.
Keep a Spare Set Where Appropriate
For laboratories with regular concrete testing work, a spare Slump Cone Set can provide useful backup.
This is particularly relevant when:
Several technicians work simultaneously
Site testing is frequent
Customers require urgent testing
Replacement equipment cannot be obtained immediately
The spare quantity should match the laboratory's workload.
Don't Turn the Spare Set into Spare Parts
This is a common inventory problem.
The laboratory keeps:
1 Complete Spare Set
Then somebody borrows the Tamping Rod.
Another technician takes the Measuring Scale.
Later, the Base Plate is used with another cone.
The store still shows:
“1 Spare Slump Cone Set.”
But physically there is no complete spare set anymore.
Periodic stock checks should therefore count the individual components.
Count Complete Usable Sets
Suppose a laboratory owns:
5 Slump Cones
5 Base Plates
4 Measuring Scales
3 Tamping Rods
The number of immediately complete sets may only be:
3
This is the number that matters when scheduling technicians.
Standardise the Laboratory's Slump Cone Set
Once the technical department approves a particular configuration, the laboratory can create a standard purchasing description.
For example:
STANDARD SLUMP CONE COMPLETE SET
Slump Cone – 1.5mm
Base Plate – 40 × 40cm
Slump Measuring Scale
Tamping Rod – 50cm
This simplifies future repeat orders.
Create a Separate Description for 60cm
If the laboratory also requires the optional 60cm Tamping Rod, identify it separately.
For example:
Slump Cone Set – TR50
and
Slump Cone Set – TR60
This helps purchasing avoid ordering the wrong configuration.
New Laboratory Setup
A new material testing laboratory may need to purchase many items at the same time.
Large machines usually receive the most attention, but compact testing equipment should not be forgotten.
Depending on the laboratory's testing scope, the setup may include:
Slump Cone Sets
Plastic Concrete Cube Moulds
Cast Iron Concrete Cube Moulds
Concrete Test Hammer
Other concrete testing equipment
Planning the compact equipment together can make the laboratory operational sooner.
Expanding a Laboratory Creates Additional Demand
A laboratory may begin with one technician and later expand to several mobile testing teams.
As the business grows, additional equipment may be required.
For example:
New Technician → Additional Site Testing Set
New Vehicle → Additional Mobile Equipment
More Concrete Testing Jobs → Additional Cube Moulds
New Branch → New Laboratory Equipment
Slump Cone demand can therefore grow together with the laboratory's testing capacity.
Buying for a New Branch
If a testing company opens another branch, the new location should not depend entirely on equipment from the original laboratory.
A standard equipment list can be duplicated where appropriate.
For example:
2 × Slump Cone Complete Sets
Required Quantity of Cube Moulds
Concrete Test Hammer
Other Required Equipment
The actual list depends on the services offered by the new branch.
Purchasing Should Compare the Complete Set
When requesting quotations, compare:
Slump Cone thickness
Base Plate size
Measuring Scale
Tamping Rod
Tamping Rod length
Included accessories
Required technical specification
Do not assume that every supplier's “Slump Cone Set” includes the same items.
Example Laboratory RFQ
A clear enquiry can be written as:
Product: Slump Cone Complete Set
Quantity: 3 Sets
Cone Thickness: 1.5mm
Base Plate: 40 × 40cm
Measuring Scale: Included
Tamping Rod: 50cm
Application: Material Testing Laboratory / Site Testing
This gives the supplier a clear requirement.
Example Mobile Testing Team Order
A laboratory adding two new site-testing teams may request:
Slump Cone Complete Set – 2 Sets
plus
Plastic Concrete Cube Moulds – Required Quantity
The laboratory can then prepare both teams with their own compact concrete testing equipment.
Need Slump Cone Equipment for a Material Testing Laboratory?
MTM Precision supplies Slump Cone Complete Sets consisting of:
Slump Cone – 1.5mm thickness
Base Plate – 40 × 40cm
Slump Measuring Scale / Measuring Frame
Tamping Rod – 50cm standard
Optional:
60cm Tamping Rod – Additional Charge
We support:
Material Testing Laboratories
Construction Laboratories
Ready-Mix Concrete Companies
Contractors
Precast Manufacturers
Universities
QA/QC Teams
Customers can provide the required quantity, application, and applicable specification for quotation.
Why Choose MTM Precision?
MTM Precision supplies practical Concrete Testing Equipment for customers throughout Malaysia.
Our key compact concrete testing products include:
Slump Cone Complete Set
Plastic Concrete Cube Mould
Cast Iron Concrete Cube Mould
Concrete Test Hammer
These products are suitable for laboratories that need compact equipment for both permanent laboratory use and mobile site-testing operations.
We support new laboratory setups, additional testing teams, new branches, replacement equipment, and repeat orders.
Contact MTM Precision
MTM Precision Sdn. Bhd.
Showroom & Service Centre
No. 29-1 & 29-2, Jalan Bandar 18,
Pusat Bandar Puchong,
47160 Puchong, Selangor, Malaysia
Website: www.mtmpre.com.my
Email: mtmpre@yahoo.com
WhatsApp: +6016-660 7346
SEO Keywords
Slump Cone Material Testing Laboratory Malaysia, Slump Cone Laboratory Malaysia, Concrete Laboratory Equipment Malaysia, Slump Cone Complete Set Malaysia, Slump Cone Supplier Malaysia, 1.5mm Slump Cone Malaysia, Slump Cone 40x40cm Base Plate Malaysia, 50cm Tamping Rod Malaysia, 60cm Tamping Rod Malaysia, Plastic Cube Mould Laboratory Malaysia, Cast Iron Cube Mould Malaysia, Concrete Test Hammer Malaysia, Concrete Testing Equipment Supplier Malaysia.
14 Aug 2026