How to Perform a Two-Peg Test for Auto Level Malaysia

How to Perform a Two-Peg Test for Auto Level Malaysia

 

How can you check whether an auto level is still giving a reliable horizontal line of sight?

 

One commonly used field procedure is the two-peg test.

 

For contractors, surveyors, engineers and construction teams in Malaysia, a two-peg test can help identify possible collimation or line-of-sight error before the instrument is used for important levelling work.

 

It is especially useful when:

 

An auto level has been dropped

 

Readings appear inconsistent

 

Closing errors are unusual

 

The instrument has undergone rough transportation

 

You want a field check between calibration intervals

 

A two-peg test is useful, but it should not be confused with a complete professional calibration or internal instrument diagnosis.

 

What Is a Two-Peg Test?

 

The two-peg test compares levelling observations from two instrument positions.

 

The basic idea is:

 

First Setup → Approximately Equal Sight Distances

 

followed by:

 

Second Setup → Instrument Positioned Close to One Staff

 

The first setup helps establish the true difference in elevation between two stable points while reducing the influence of line-of-sight error.

 

The second setup helps reveal whether the observed line of sight agrees with that expected elevation difference.

 

What Does the Test Check?

 

The test is primarily used to investigate whether the instrument's line of sight is correctly related to the horizontal reference established by the instrument.

 

If excessive error exists, the auto level may require:

 

Inspection → Adjustment → Calibration/Verification

 

If abnormal compensator behaviour or mechanical damage is also present, repair may be necessary first.

 

Equipment Required

 

You will typically need:

 

Auto level

 

Stable survey tripod

 

Levelling staff or suitable staffs

 

Two stable reference points

 

Measuring tape or suitable distance measurement method

 

Field notes or recording sheet

 

The equipment itself must be in reasonable condition.

 

A loose tripod or damaged staff can make the test misleading.

 

Step 1: Select Two Stable Points

 

Choose two stable locations, Point A and Point B.

 

They should be sufficiently separated to make the test meaningful while remaining practical for the site and instrument.

 

Avoid placing the points on:

 

Soft soil

 

Loose gravel

 

Mud

 

Unstable boards

 

Surfaces likely to move

 

The exact test distance should follow the procedure appropriate to your instrument, site and service practice.

 

Step 2: Position the Auto Level Approximately Midway

 

Set the auto level approximately halfway between Point A and Point B.

 

The objective is to keep the sight distances to both points approximately equal.

 

Why?

 

Because when sight distances are approximately equal, a consistent line-of-sight error tends to affect both readings similarly, so the difference between the two readings provides a useful estimate of the true elevation difference.

 

Step 3: Level and Focus the Instrument

 

Set up the tripod firmly.

 

Mount the auto level and centre the circular bubble.

 

Allow the compensator to settle.

 

Then:

 

Focus the crosshair

 

Focus the staff

 

Eliminate parallax

 

Confirm tripod stability

 

Do not rush this step.

 

Poor setup can invalidate the test.

 

Step 4: Take the Reading at Point A

 

Place the levelling staff vertically on Point A.

 

For example:

 

Reading A1 = 1.250 m

 

Record the value carefully.

 

Step 5: Take the Reading at Point B

 

Move the staff to Point B, or observe the second staff if two staffs are being used.

 

For example:

 

Reading B1 = 1.550 m

 

The observed elevation difference is:

 

B1 − A1 = 1.550 − 1.250 = 0.300 m

 

Because Point B gives the larger staff reading, Point B is lower than Point A by approximately:

 

0.300 m

 

This becomes the reference difference for the next stage.

 

Step 6: Move the Auto Level Close to One Point

 

Move the instrument closer to Point A while keeping both points visible.

 

Now the sight distances are intentionally unequal.

 

Set up the instrument again carefully.

 

Level it and allow the compensator to settle.

 

Step 7: Read Point A Again

 

Suppose the new reading is:

 

Reading A2 = 1.100 m

 

Record it.

 

Because the instrument is close to Point A, the effect of line-of-sight error on this short sight is relatively small.

 

Step 8: Calculate the Expected Reading at Point B

 

From the first setup, we determined that Point B is approximately:

 

0.300 m lower than Point A

 

Therefore, if:

 

A2 = 1.100 m

 

the expected Point B reading should be approximately:

 

1.100 + 0.300 = 1.400 m

 

Now observe Point B.

 

Step 9: Compare Actual and Expected Readings

 

Suppose the actual second reading is:

 

B2 = 1.420 m

 

Expected:

 

1.400 m

 

Observed:

 

1.420 m

 

Difference:

 

0.020 m = 20 mm

 

This indicates a discrepancy that should be assessed against the instrument specification and the test procedure being used.

 

Do not automatically adjust the instrument based on one rushed test.

 

Repeat the test if necessary.

 

Why Equal Sight Distances Matter

 

Imagine the auto level has a small line-of-sight error.

 

If Point A and Point B are approximately the same distance from the instrument, the error affects both observations by approximately the same amount.

 

When the readings are subtracted, much of that common effect cancels.

 

That is the principle behind the first part of the two-peg test.

 

Common Two-Peg Test Mistakes

 

Incorrect testing can make a good auto level appear faulty.

 

Common mistakes include:

 

Unstable tripod

 

Staff leaning

 

Staff sinking

 

Incorrect recording

 

Wrong subtraction

 

Points moving

 

Excessive atmospheric shimmer

 

Poor focusing

 

Parallax

 

First setup not reasonably centred

 

Moving the reference points during the test

 

Control these factors before judging the instrument.

 

Staff Position Is Critical

 

Keep the levelling staff vertical.

 

If the staff leans differently between observations, the comparison becomes unreliable.

 

A staff bubble may help.

 

Also ensure that telescopic staff sections are fully extended and locked correctly.

 

Avoid Hot Ground for Precision Checks

 

Malaysia's strong sunlight can create atmospheric shimmer over:

 

Asphalt

 

Concrete

 

Bare soil

 

This can make the staff image unstable at longer distances.

 

For a meaningful accuracy check, choose suitable conditions whenever possible.

 

Repeat the Test

 

If the first result suggests a significant error, repeat the test.

 

A repeat test helps determine whether the discrepancy is consistent.

 

If one test shows a large error and the next shows something completely different, investigate:

 

Setup → Tripod → Staff → Technique → Environment

 

before concluding that the instrument requires adjustment.

 

Should You Adjust the Auto Level Yourself?

 

That depends on the instrument and your technical competence.

 

Randomly turning adjustment screws is not recommended.

 

An incorrect adjustment can make the instrument worse.

 

If the auto level consistently fails the test beyond the acceptable limits for the model and procedure, professional inspection is usually the safer approach.

 

Two-Peg Test vs Calibration

 

A two-peg test is an excellent field accuracy check.

 

But it is not the same as a complete calibration service.

 

Think of it this way:

 

Two-Peg Test → Is there evidence of a possible accuracy problem?

 

Professional Service → What is wrong, what adjustment or repair is required, and what is the verified condition afterward?

 

Both have a role.

 

What If the Auto Level Passes the Two-Peg Test but Readings Are Still Unstable?

 

Then the problem may be elsewhere.

 

Check:

 

Tripod

 

Levelling staff

 

Ground stability

 

Parallax

 

Site vibration

 

Compensator behaviour

 

Operator technique

 

A two-peg test does not diagnose every possible auto level fault.

 

What If the Auto Level Was Dropped?

 

Even if the instrument was recently calibrated, a significant impact can change its condition.

 

After a drop:

 

Visual Inspection → Field Accuracy Check → Professional Inspection if Necessary

 

Do not continue critical work solely because the calibration certificate is recent.

 

How Often Should You Perform a Two-Peg Test?

 

There is no single interval suitable for every company.

 

A field check may be appropriate:

 

Before important work

 

After significant impact

 

When readings become suspicious

 

After rough transportation

 

As part of internal equipment-control procedures

 

Scheduled calibration should still follow the company's project, quality or equipment-management requirements.

 

Topcon Auto Level Accuracy Check Malaysia

 

Owners of professional Topcon auto levels can use field checks as part of good equipment management.

 

If a Topcon AT-B series auto level repeatedly shows questionable results, MTM Precision can inspect the instrument and advise whether it requires:

 

Adjustment

 

Calibration

 

Repair

 

Replacement

 

The objective should be to identify the actual condition before returning the instrument to critical site work.

 

Auto Level Calibration & Repair Malaysia

 

MTM Precision provides surveying instrument service support for contractors, surveyors, engineers and construction companies.

 

Our support includes:

 

Auto level inspection

 

Accuracy assessment

 

Calibration

 

Repair

 

Topcon surveying equipment

 

Survey tripods

 

Levelling staffs

 

Survey accessories

 

Replacement and upgrade advice

 

Customers can bring questionable instruments to our Puchong service centre for assessment.

 

Make Field Accuracy Checks Part of Surveying Equipment Management

 

Do not wait until a construction error appears before asking whether the auto level is accurate.

 

A better equipment lifecycle is:

 

Buy → Use → Field Check → Calibrate → Repair → Verify → Return to Service

 

The two-peg test is one useful part of that process.

 

MTM Precision supports the complete surveying equipment lifecycle from purchase through calibration, repair, replacement and upgrade.

 

MTM Precision Sdn Bhd

 

Surveying Equipment • Calibration • Repair • Accessories

 

Website: www.mtmpre.com.my

 

WhatsApp: +6016-660 7346

 

Email: mtmpre@yahoo.com

 

Showroom & Service Centre

 

No. 29-1 & 29-2, Jalan Bandar 18,

Pusat Bandar Puchong,

47160 Puchong, Selangor, Malaysia.


 

21 Aug 2026