Factory Lighting Problems What Should You Measure Malaysia

Factory Lighting Problems What Should You Measure Malaysia A factory supervisor may hear complaints such as: “This workstation is too dark.” “Operators cannot see small defects clearly.” “The inspection area looks bright, but workers still struggle to see the product.” “Some parts of the production line are much darker than others.” The first reaction may be: “Install more lights.” But before changing the lighting system, it is useful to understand the actual condition. The measurement problem may involve: Illuminance → Workstation Position → Task Area → Lighting Uniformity → Time / Operating Condition The correct starting point is not: “Which lux meter should we buy?” It is: “Where is the lighting problem, and what task is being performed there?” 1. Start With the Work Task Not every area of a factory is used for the same purpose. Lighting requirements can differ between: General walkways Warehouses Packing stations Assembly areas Machine operating areas Inspection stations Laboratories Quality-control areas Offices Loading bays A worker inspecting a small surface defect has a different visual task from someone walking through a warehouse aisle. The measurement should therefore begin at the actual work area. 2. Measure Illuminance With a Lux Meter A lux meter measures illuminance. Instead of saying: “This workstation looks dark.” you can obtain a numerical measurement. This allows comparisons between: Workstation A Workstation B Inspection Table Packing Area Walkway Warehouse Aisle Measurement turns a subjective complaint into useful information. 3. Measure Where the Work Happens One common mistake is taking the measurement at an arbitrary location. For example: Measuring near the ceiling light may not tell you how much light reaches the actual inspection surface. The measurement location should reflect the task. Depending on the application, this could be: Workbench Inspection surface Assembly table Machine control panel Packing table Product inspection area The important question is: How much illumination reaches the area where the worker actually needs to see? 4. One Factory Can Have Very Different Lighting Conditions A production floor may appear generally bright. But measurements can reveal major differences. For example: Zone A Assembly Zone B Inspection Zone C Packing Zone D Storage Zone E Walkway This allows the factory to build a simple lighting map. 5. Don't Measure Only the Brightest Spot Suppose an inspection table has one bright area directly below a lamp. A single reading at that point may look good. But other parts of the work surface may be much darker. Take measurements at several representative points where appropriate. This helps identify uneven lighting. 6. Lighting Uniformity Can Matter Workers may complain: “One side of the table is bright, but the other side is dark.” This is not necessarily a problem of insufficient total lighting. It may be a distribution problem. Compare multiple positions across the task area. For example: Left Centre Right or a measurement grid where appropriate. This provides more useful information than one reading. 7. Inspection Areas Need Special Attention Quality-control and inspection tasks may involve: Small defects Fine markings Surface finish Colour differences Product dimensions Printed labels Electronic components If operators repeatedly struggle to identify defects, lighting should be one of the conditions investigated. The solution may involve more than simply increasing brightness. Workstation design, glare and task conditions can also matter. 8. Lighting Can Change Throughout the Day Factories with windows, skylights or open areas may receive significant daylight. This means conditions can differ between: Morning Midday Afternoon Night Shift A measurement taken at noon may not represent the night-shift condition. Where daylight contributes significantly, measurements at different times can be useful. 9. Compare Day and Night Shifts Suppose workers on the day shift have no complaints, but night-shift workers do. A useful comparison is: Day Shift → Lux Measurement versus Night Shift → Lux Measurement This may reveal dependence on daylight or differences in lighting-system operation. 10. Dirty or Aging Lighting Can Change Conditions Lighting performance may change over time because of: Dirty fittings Dust accumulation Failed lamps Aging components Obstructions Changes in production layout Tall racks blocking light Measurements can help identify whether a work area has changed compared with previous conditions. 11. Measure Before and After Improvement Suppose the factory: Adds LED lighting Repositions lamps Cleans fittings Adds task lighting Changes production layout Measure before the change. Then repeat measurements after the improvement under comparable conditions. This gives the facility team objective evidence of the change. 12. Warehouse Racks Can Create Dark Areas Warehouses can look bright from the main aisle while individual rack areas remain poorly illuminated. Possible measurement points include: Main Aisle Picking Position Lower Rack Upper Rack Packing Station This is particularly useful where workers need to read: Labels Part numbers Barcodes Documents 13. Production Machinery Can Block Light A lighting system may have been designed before machinery was installed. After production equipment is added, shadows can appear around: Operator stations Control panels Inspection points Maintenance areas Therefore, lighting should be measured under the actual factory layout rather than assuming the original installation still provides suitable conditions. 14. Lighting Is Sometimes Part of a Bigger Workstation Problem Suppose workers complain: “This workstation is uncomfortable.” The problem may involve more than illumination. Depending on the complaint, the investigation might expand to: Lux Noise Temperature Airflow Heat Stress This is another example of why factory environmental measurements should be considered by work area rather than isolated product categories. 15. Example: Quality Team Is Missing Small Defects Suppose a customer contacts MTM: “Our QC operators sometimes miss small defects. We think the inspection table may not be bright enough.” Instead of immediately recommending a lamp, first measure. A possible pathway: Identify Inspection Task ↓ Measure Lux at Work Surface ↓ Measure Several Points ↓ Compare Different Inspection Stations ↓ Compare Day / Night Conditions ↓ Improve Lighting ↓ Measure Again Now the factory has data to support the improvement. 16. Example: One Production Area Is Much Darker Another customer says: “Our production floor is generally okay, but one machine area is very dark.” Possible investigation: Measure Machine Workstation ↓ Compare With Nearby Stations ↓ Check Shadows / Obstructions ↓ Improve Lighting Position ↓ Repeat Measurement The customer does not necessarily need a complex monitoring system. Sometimes the right solution begins with one correctly performed measurement. What Instruments Might Be Needed? Depending on the application, the solution may include: Lux Meter For measuring workplace illuminance. Data Logging Lux Meter Where illumination needs to be monitored over time or changing conditions. Environmental Measurement Instruments Where the workstation complaint also involves temperature, heat, noise or airflow. The correct instrument depends on what the factory wants to understand. Don't Ask Only “Which Lux Meter?” The better sequence is: Worker / Quality Complaint ↓ Identify Work Task ↓ Identify Measurement Surface ↓ Measure Lux ↓ Compare Multiple Points ↓ Compare Shifts / Conditions ↓ Improve Lighting ↓ Measure Again This converts: “It looks dark.” into measurable information. One Workstation Can Have Several Environmental Problems An inspection station may simultaneously have: Poor Lighting High Noise Heat Low Air Movement The customer should not have to search four separate categories and decide which meter is needed. They can simply tell MTM: “Our operators are having problems at this workstation.” Then the measurement problem can be broken down. Factory Environmental & Safety Measurement Solutions Malaysia MTM Precision supports: Manufacturing plants Production departments Quality-control teams EHS departments Warehouses Facility managers Maintenance teams Engineers Industrial contractors with measurement solutions covering: Lux / Workplace Lighting Noise Temperature & Humidity Heat Stress Airflow Indoor Air Quality Gas Detection Environmental Monitoring Industrial Testing Our approach is: Problem → Measurement → Instrument → Improvement → Verification Need Help Investigating Factory Lighting? Tell MTM: What task is being performed? Where is the lighting problem? Does it affect inspection, assembly, packing or general work? Does the problem change between day and night shifts? Do you want to compare conditions before and after lighting improvements? We can help identify suitable measurement options for the application. MTM Precision Sdn Bhd Showroom & Service Centre No. 29-1 & 29-2, Jalan Bandar 18, Pusat Bandar Puchong, 47160 Puchong, Selangor, Malaysia WhatsApp: +6016-660 7346 Email: mtmpre@yahoo.com Website: www.mtmpre.com.my Tell us your testing problem. MTM will help you find the right measurement solution.

21 Aug 2026