How to Set 0mm Prism Constant on a Total Station Malaysia
How to Set 0mm Prism Constant on a Total Station Malaysia
Using the correct prism constant is an important part of total station surveying.
If you are using the Myzox M-1500GP 1.5-inch Mini Prism, its specified prism constant is 0 mm.
Before starting important setting-out, construction or as-built measurements, surveyors should confirm that the total station reflector configuration corresponds to the prism being used.
What Does 0mm Prism Constant Mean?
Different prism assemblies can require different prism constant corrections.
The total station uses this information when calculating reflector-based distance measurements.
For the Myzox M-1500GP:
Prism Constant = 0 mm
This does not mean that every mini prism uses 0 mm.
Always check the specification of the actual prism being used.
How Do You Set the Prism Constant?
The exact menu names and procedures vary between total station models.
However, the general process is:
1. Turn on the total station.
2. Select reflector or prism measurement mode.
3. Open the prism / reflector constant setting.
4. Enter or select the correct prism constant.
For the Myzox M-1500GP:
0 mm
5. Confirm the setting.
6. Check the target height.
7. Verify the setup against a known control point or distance when required.
Always refer to the total station manufacturer's operating manual for the exact procedure applicable to your model.
Using M-1500GP with a Topcon Total Station
For compatible reflector measurements with a Topcon total station, operators should verify the relevant prism settings before measuring.
Depending on the Topcon model, reflector-related settings may be available through measurement or EDM configuration menus.
Do not rely on memory if you are unfamiliar with the instrument.
Check the instrument manual or seek technical assistance.
Why Do Surveyors Forget to Change the Prism Constant?
One common reason is that survey teams use several reflectors on the same project.
For example:
Standard Prism → Mini Prism → Standard Prism
The operator changes the physical target but forgets that the instrument may still be using the previous reflector configuration.
This is why a simple field rule is useful:
Whenever the prism changes, check the prism constant.
What Happens If the Prism Constant Is Wrong?
An incorrect prism constant can introduce a systematic offset into reflector distance measurements.
That can then influence calculated positions.
The error chain can be:
Wrong Prism Setting → Wrong Distance → Coordinate Error → Setting-Out Error
This is particularly undesirable for:
Column setting out
Wall positioning
Anchor bolt surveys
Structural steel
Foundation surveys
Road construction
Drainage work
As-built surveys
Don't Forget Target Height
Surveyors sometimes focus on the prism constant while overlooking another important setting:
Target Height
The prism constant and target height are different parameters.
Both need to be correct.
Before important observations, verify:
Prism Constant = Correct
Target Height = Correct
Target Level = Correct
Station Setup = Correct
Myzox M-1500GP Key Features
The M-1500GP provides:
1.5-inch / 38 mm mini prism
0 mm prism constant
Dual Lock system
Screw Lock / Quick Lock
Wide tilting capability
Maximum tilting angle approximately 38°
Ø9 mm pole
Circular level
Removable prism cover
Its compact configuration makes it useful for selected measurements around buildings and other structures.
When Is a 0mm Mini Prism Useful?
The M-1500GP can be particularly useful for:
Construction Setting Out
Compact positioning around walls, columns and foundations.
Structural Survey
Measurements around steel structures and other building components.
As-Built Survey
Recording selected completed construction positions.
Detail Survey
Collecting points around buildings, drains and infrastructure.
Industrial Survey
Working around machinery foundations and factory structures.
How to Check Before Starting Survey Work
A simple field checklist can prevent many avoidable problems:
Step 1 — Confirm the prism model
Are you actually using the M-1500GP?
Step 2 — Confirm prism constant
M-1500GP = 0 mm
Step 3 — Confirm target height
Check the actual target setup.
Step 4 — Level the target
Use the circular level correctly.
Step 5 — Check control
Measure an established reference where appropriate.
Step 6 — Start the survey
Only proceed with critical setting-out work after the setup has been verified.
My Total Station Is Still Measuring Wrong — What Next?
If the prism constant is correct but measurements still appear incorrect, investigate other possible causes.
Check:
Target height
Prism condition
Pole condition
Total station setup
Tripod stability
Station coordinates
Backsight
Control points
Instrument calibration
Surveying accuracy depends on the entire measurement system.
Total Station Service & Calibration Malaysia
If measurement discrepancies remain after the basic field checks, the total station may require professional inspection.
MTM Precision supports surveying customers with Topcon total station service and calibration in Malaysia, in addition to supplying prisms and other surveying accessories.
This allows customers to obtain support across the complete workflow:
Prism Selection → Correct Setup → Troubleshooting → Instrument Service → Calibration
Looking for Myzox M-1500GP in Malaysia?
Common searches include:
How to Set Prism Constant Total Station Malaysia
How to Set 0mm Prism Constant Malaysia
Topcon Prism Constant Setting Malaysia
Myzox M-1500GP Malaysia
0mm Mini Prism Malaysia
38mm Mini Prism Malaysia
Mini Prism for Topcon Malaysia
Total Station Accessories Malaysia
MTM Precision supplies professional surveying equipment and accessories for land surveyors, construction contractors and engineering companies throughout Malaysia.
Contact MTM Precision
MTM Precision Sdn Bhd
Showroom & Service Centre
No. 29-1 & 29-2, Jalan Bandar 18,
Pusat Bandar Puchong,
47160 Puchong, Selangor, Malaysia.
WhatsApp: +6016-660 7346
Email: mtmpre@yahoo.com
Website: www.mtmpre.com.my
Contact MTM Precision for Myzox M-1500GP price and availability, prism setup assistance, Topcon total station service and calibration enquiries in Malaysia.
22 Aug 2026