4-in-1 Gas Detector for Gas Transmission & Distribution Malaysia Fosensor FS11301

4-in-1 Gas Detector for Gas Transmission & Distribution Malaysia Fosensor FS11301 Portable gas detection can be required in industrial gas transmission and distribution applications where workers need to monitor identified atmospheric hazards. The Fosensor FS11301 Portable 4-in-1 Gas Detector simultaneously monitors: EX / Combustible Gas H2S / Hydrogen Sulphide CO / Carbon Monoxide O2 / Oxygen According to Fosensor's product documentation, Gas Transmission and Distribution is one of the listed main applications for the FS11301. The detector is available in two configurations: Natural Diffusion and Pump Suction. This allows users to choose between surrounding-atmosphere monitoring and active gas sampling according to the required work procedure. What Does the Fosensor FS11301 Detect? The FS11301 provides four measuring channels: GasMeasuring RangeResolutionEX0100% LEL1% LELH2S0100 ppm1 ppmCO01000 ppm1 ppmO2030% VOL0.1% VOL This allows combustible gas, two toxic gases and oxygen concentration to be monitored simultaneously. Why Monitor LEL, H2S, CO and O2 Together? A single reading cannot represent every atmospheric hazard. For example: LEL relates to combustible-gas concentration. H2S and CO are separate toxic-gas measurements. O2 provides oxygen concentration. Where these four parameters correspond to the identified hazards, a four-gas detector allows the operator to monitor all four through one portable instrument. EX / LEL Measuring Range The FS11301 combustible-gas channel provides: Range: 0100% LEL Resolution: 1% LEL The manufacturer's listed alarm points are: Low Alarm: 20% LEL High Alarm: 50% LEL Alarm settings should be selected according to the applicable workplace requirements. H2S Measuring Range The H2S channel provides: Range: 0100 ppm Resolution: 1 ppm The manufacturer's listed alarm points are: Low Alarm: 10 ppm High Alarm: 35 ppm CO Measuring Range The CO channel provides: Range: 01000 ppm Resolution: 1 ppm The manufacturer's listed alarm points are: Low Alarm: 50 ppm High Alarm: 150 ppm Oxygen Measuring Range The oxygen channel provides: Range: 030% VOL Resolution: 0.1% VOL The manufacturer's listed alarm points are: Low Alarm: 19.5% VOL High Alarm: 23.5% VOL Users should follow their applicable safety procedures rather than assuming that manufacturer-listed alarm settings automatically satisfy every site requirement. Natural Diffusion Version/span> The FS11301 Natural Diffusion version relies on surrounding gas reaching the detector sensors naturally. Specified dimensions: 135 × 68 × 43 mm This configuration can be considered for professional portable four-gas monitoring where active sampling is not required. Pump Suction Version The FS11301 Pump Suction version actively draws a gas sample toward the detector. Specified dimensions: 150 × 68 × 60 mm The reason to select the Pump Suction model is therefore straightforward: The application requires active sampling. It should not simply be selected because it is the higher-priced FS11301. Can the Pump Version Become a Diffusion Detector? Yes. The manufacturer's operating manual describes how the Pump Suction configuration can be changed to Natural Diffusion. The procedure involves: Removing the four rear screws. Removing the pump suction module. Installing the Natural Diffusion front cover. Re-tightening the four screws. After this procedure, the detector operates in Natural Diffusion mode. This gives the pump-equipped FS11301 additional flexibility for users who encounter different sampling requirements. Professional Alarm Functions The FS11301 provides several warning methods: LCD indication LED warning Audible alarm Vibration Backlight When an alarm condition occurs, the detector can activate its buzzer, flashing red indicator, backlight and vibrator. This multi-alarm approach helps make an abnormal reading noticeable to the operator. STEL, TWA and MAX Settings The FS11301 alarm menu includes: Low Alarm High Alarm STEL TWA MAX These functions help distinguish the FS11301 from very basic four-gas instruments that primarily provide instantaneous concentration readings. Users should configure these parameters according to the applicable occupational and workplace safety requirements. Alarm Records The detector provides gas alarm record viewing. The operator can select a gas type through the instrument interface and display the corresponding record. This provides additional information beyond the current gas concentration. Curve Graph Display The FS11301 also provides a curve graph function. Users can browse changes in measured parameters through the instrument interface. Together with the alarm-record function, this strengthens the detector's professional monitoring capability. Response Time According to the FS11301 operating manual: Response Time: T < 15 seconds The stated display error is: ≤ ±2% FS The listed working principles are: Electrochemical and Catalytic Combustion Actual field performance can depend on gas type, sensor condition, sampling method and operating environment. Battery and Operating Specifications The FS11301 uses a: 3000mAh lithium battery The manufacturer's specifications state: Charging time: approximately 4 hours Standby time: more than 8 hours Working voltage: DC 5V Working temperature: -20°C to 50°C Working humidity: 095% RH, non-condensing The detector uses a Type-C charging connection. Charging Precaution The FS11301 manual warns against charging the detector at the testing site where plugging or unplugging the charger could create a fire or explosion hazard. The manual also states that the battery pack must not be charged in an explosive gas atmosphere. Users should always follow the manufacturer's instructions and applicable site procedures. Is the FS11301 a Gas Leak Detector? The FS11301 measures the concentrations of its four specified gas channels. However, buyers should distinguish between a portable multi-gas detector and specialised equipment designed to locate the exact physical source of a leak. The FS11301 documentation supports measurement of: EX + H2S + CO + O2 It should not automatically be presented as a dedicated pipeline leak-location instrument. If the requirement is to pinpoint a leak source, tell MTM Precision the application so the appropriate type of detector can be selected. Can the FS11301 Detect Natural Gas? The standard FS11301 documentation describes its combustible-gas channel as: EX: 0100% LEL The supplied manual does not provide enough information to make a universal claim about response or calibration for every specific combustible gas. If your project requires measurement of a particular gas, confirm the required gas and sensor/calibration configuration before ordering. Applications Listed by Fosensor The FS11301 manufacturer lists: Petroleum Chemical Industry Environmental Protection Metallurgy Refining Gas Transmission and Distribution Biochemical Pharmaceuticals Agriculture This gives the FS11301 a much broader professional industrial positioning than simply marketing it as a general-purpose low-cost four-gas detector. FS11301 vs Wintact WT8812 MTM Precision can offer different product levels according to the customer's requirements. Wintact WT8812 Economical 4-in-1 Gas Detector Suitable when value for money is the main priority. Fosensor FS11301 Natural Diffusion Professional 4-in-1 Gas Detector Suitable when additional monitoring functions are required without active pump sampling. Fosensor FS11301 Pump Suction Professional 4-in-1 Gas Detector + Active Sampling Suitable when the testing procedure requires pump suction. This provides a clear progression: Economical → Professional → Professional Pump Suction Why Choose Fosensor FS11301? The FS11301 provides a combination of: Four simultaneous gas channels Natural Diffusion or Pump Suction options STEL TWA MAX Alarm records Curve graph Audible alarm LED warning Vibration alarm 3000mAh rechargeable battery Convertible pump configuration These functions give customers a reason to choose FS11301 when their requirements go beyond a basic four-gas detector. How Often Should FS11301 Be Calibrated? The manufacturer's manual states that the detector should be periodically calibrated and specifies: The calibration cycle should not exceed one year. The manual also warns that calibration functions are intended for professionals because incorrect calibration can affect test results. Looking for a 4-Gas Detector in Malaysia? For gas transmission and distribution applications where the identified monitoring requirement includes: LEL + H2S + CO + O2 the Fosensor FS11301 Portable 4-in-1 Gas Detector is one professional option to consider. Choose: FS11301 Natural Diffusion for professional surrounding-atmosphere monitoring. FS11301 Pump Suction when active gas sampling is required. For customers primarily seeking an economical four-gas detector, consider the: Wintact WT8812 Contact MTM Precision with your required gas, application and sampling method for product selection and quotation. Contact MTM Precision MTM Precision Sdn Bhd No. 29-1 & 29-2, Jalan Bandar 18, Pusat Bandar Puchong, 47160 Puchong, Selangor, Malaysia. Website: www.mtmpre.com.my WhatsApp: +6016-660 7346 Email: mtmpre@yahoo.com

25 Aug 2026