OTYWELL G10S-SO2 Gas Detector for Factory, Boiler and Industrial Safety Malaysia
OTYWELL G10S-SO2 Gas Detector for Factory, Boiler and Industrial Safety Malaysia
Sulphur dioxide, commonly written as SO2, can be relevant in certain industrial environments involving combustion, fuels, chemical processes and other operations where sulphur dioxide has been identified as a potential gas hazard.
For workers who require dedicated portable SO2 monitoring, the OTYWELL G10S-SO2 Portable Sulphur Dioxide Gas Detector provides a single gas solution for industrial safety and maintenance applications.
The G10S-SO2 configuration supplied by MTM Precision has a measuring range of:
SO2: 0-20 ppm
OTYWELL G10S-SO2 Specification
Brand: OTYWELL
Model: G10S-SO2
Target Gas: Sulphur Dioxide
Gas: SO2
Measuring Range: 0-20 ppm
Type: Portable Single Gas Detector
The G10S-SO2 is specifically configured for SO2 monitoring.
Where May SO2 Monitoring Be Relevant?
The need for SO2 monitoring depends on the actual industrial process and identified gas hazards.
Potential applications can include certain:
Factory environments
Boiler areas
Combustion-related processes
Industrial maintenance work
Chemical processing areas
Fuel-related operations
Process plants
Environmental and safety work
Customers should confirm that SO2 is the actual target gas before purchasing.
SO2 Detector for Factory Safety
Factories can contain very different processes.
Therefore, asking for a "factory gas detector" is not enough to select the correct instrument.
Before purchasing, determine:
Which gas needs to be monitored?
What is the required range?
Is personal monitoring required?
Is area monitoring required?
Is the customer measuring workplace gas or stack emissions?
If SO2 is the identified target gas and a portable personal detector is required, the G10S-SO2 can be considered.
SO2 Detector for Boiler Areas
Boiler and combustion applications can lead customers to search for sulphur dioxide monitoring equipment.
However, the correct instrument depends on what the customer is trying to measure.
A maintenance technician requiring portable personal SO2 monitoring has a different requirement from an engineer performing detailed flue gas or stack emission measurements.
The G10S-SO2 is a portable single gas safety detector.
It should not automatically be treated as a combustion analyzer or stack emission analyzer.
Personal SO2 Monitoring vs Emission Measurement
This distinction is important.
Personal SO2 Monitoring
The detector is carried by a worker during industrial activities.
The objective is to monitor SO2 concentration around the worker according to the detector's operating principle.
The G10S-SO2 can be considered for this type of dedicated portable monitoring.
Stack or Flue Gas Measurement
The objective may be to measure gases directly in a chimney, exhaust duct, boiler flue or industrial emission stream.
This can require specialized sampling equipment and a different analyzer.
A portable personal SO2 detector should not automatically be used as a replacement for a dedicated flue gas or emission analyzer.
SO2 Detector for Industrial Maintenance
Maintenance teams may work around industrial equipment during:
Routine inspection
Preventive maintenance
Breakdown repair
Shutdown maintenance
Process equipment inspection
Boiler maintenance
Plant servicing
Where SO2 has been identified as a potential gas hazard, portable SO2 monitoring may form part of the site's safety procedures.
G10S-SO2 for Shutdown Maintenance
Industrial shutdowns can involve temporary work conditions that differ from normal plant operation.
Maintenance personnel may access equipment, process areas or enclosed locations that are not routinely entered.
Before selecting a detector, determine the complete atmospheric monitoring requirement.
If the only target gas is SO2 and the required range is within 0-20 ppm, the G10S-SO2 may be considered.
If several gases need to be monitored, a different configuration may be required.
Does a Standard 4-in-1 Detector Measure SO2?
Not necessarily.
A commonly requested 4-in-1 gas detector configuration may include:
LEL + O2 + H2S + CO
SO2 is not automatically included.
If sulphur dioxide monitoring is required, customers should specifically confirm that the selected detector includes an SO2 sensor.
Do not assume that every multi gas detector measures SO2.
G10S-SO2 vs G10S-H2S
SO2 and H2S are different gases.
G10S-SO2
Gas: SO2
Range: 0-20 ppm
G10S-H2S
Gas: H2S
Range: 0-100 ppm
The detectors are not interchangeable.
A customer requiring sulphur dioxide monitoring should select an SO2 detector rather than an H2S detector.
G10S-SO2 vs G10S-CO
The G10S-CO is designed for carbon monoxide.
CO: 0-1000 ppm
The G10S-SO2 is designed for sulphur dioxide.
SO2: 0-20 ppm
Both gases may be associated with certain industrial or combustion environments, but they are different measurement parameters.
Customers should identify which gas or gases need to be monitored.
G10S-SO2 vs G10S-O2
The G10S-O2 measures oxygen concentration.
O2: 0-30% VOL
The G10S-SO2 measures sulphur dioxide.
SO2: 0-20 ppm
An O2 detector cannot provide an SO2 reading.
An SO2 detector cannot provide an oxygen reading.
Where several atmospheric parameters are required, customers should evaluate the complete gas detection requirement.
Portable vs Fixed SO2 Gas Detector
Customers may also need to decide between portable and fixed monitoring.
Portable SO2 Detector
Carried by personnel or used for temporary monitoring.
The G10S-SO2 falls into this category.
Fixed SO2 Detection System
Installed permanently at selected monitoring locations for continuous area monitoring.
The correct solution depends on the facility and monitoring objective.
A portable detector should not automatically replace a properly designed fixed system where permanent monitoring is required.
Bump Test for G10S-SO2
Portable gas detectors require appropriate functional checking.
A bump test helps verify that the detector and alarm system respond appropriately when exposed to the relevant test condition.
A bump test is different from calibration.
Users should follow the manufacturer's instructions and their workplace gas detector procedures.
Calibration of G10S-SO2
Calibration checks detector response against an appropriate known reference and allows adjustment where required.
OTYWELL advises that instruments are 100% calibrated before shipment and can be supplied with calibration or test documentation.
After the detector enters service, users should follow an appropriate calibration and maintenance programme.
Sensor Life
The sensor in a portable gas detector is a consumable component.
For the OTYWELL G10S configurations being introduced by MTM Precision, typical sensor life is approximately:
2-3 years
Actual sensor life depends on factors including:
Sensor technology
Gas exposure
Operating environment
Temperature
Humidity
Storage
Frequency of use
Maintenance
Customers should consider future sensor replacement as part of the detector's long-term operating cost.
OTYWELL G10S Gas Detector Configurations
MTM Precision is introducing several G10S single gas detector configurations:
G10S-CO
CO: 0-1000 ppm
G10S-H2S
H2S: 0-100 ppm
G10S-O2
O2: 0-30% VOL
G10S-NH3
NH3: 0-100 ppm
G10S-SO2
SO2: 0-20 ppm
Each configuration is designed around a specific target gas.
Example 1: Factory Personal SO2 Monitoring
Application: Industrial maintenance
Target Gas: SO2
Requirement: Portable personal monitoring
Required Range: Within 0-20 ppm
The OTYWELL G10S-SO2 can be considered where its specifications match the customer's requirement.
Example 2: Boiler Technician
Application: Boiler area maintenance
Target Gas: SO2
Requirement: Portable worker monitoring
The G10S-SO2 may be considered if SO2 is the identified gas hazard and its range matches the requirement.
Example 3: Stack Emission Testing
Application: Chimney or stack emission measurement
Requirement: Measure process exhaust or flue gas
The customer should not automatically select a portable personal SO2 detector.
A suitable emission, flue gas or process analyzer may be required depending on the measurement objective.
Example 4: Multiple Gas Requirement
Application: Industrial safety monitoring
Required Gases: O2 + CO + SO2
A single G10S-SO2 only measures sulphur dioxide.
The customer should discuss the complete multi gas requirement before purchasing.
Who May Need a Portable SO2 Detector?
Potential users include:
Factory maintenance departments
Industrial plants
Boiler maintenance contractors
Process plants
Chemical industry users
Engineering contractors
EHS departments
Safety teams
Facility management companies
Industrial shutdown contractors
The correct detector depends on the actual target gas and measurement objective.
What Should You Send for a Quotation?
For faster model selection, send MTM Precision:
Target Gas: SO2
Application: Factory, boiler, process plant, maintenance or other
Required Range: If specified
Personal Monitoring: Yes / No
Area Monitoring: Yes / No
Stack or Flue Measurement: Yes / No
Portable or Fixed: Specify requirement
Quantity: Number of detectors required
Calibration Requirement: If specified
Customers can also send their existing detector model, tender specification or technical requirement for comparison.
OTYWELL G10S-SO2 Supplier Malaysia
MTM Precision supplies portable gas detection and industrial testing equipment for factory safety, industrial maintenance, boiler areas, process plants, facility management and workplace safety applications in Malaysia.
For customers searching for an SO2 detector, sulphur dioxide gas detector, portable SO2 monitor or SO2 detector for industrial use, the OTYWELL G10S-SO2 can be considered where its 0-20 ppm range and portable single gas configuration match the requirement.
Before purchasing, confirm whether the requirement is for personal gas monitoring, fixed area monitoring or stack and flue gas measurement.
Contact MTM Precision
MTM Precision Sdn. Bhd. (744811-A)
Telephone: +603-8080 7172
WhatsApp: +6016-660 7346
Email: mtmpre@yahoo.com / enquiry@mtmpre.com.my
Website: www.mtmpre.com.my
Showroom & Service Centre:
No. 29-1 & 29-2, Jalan Bandar 18,
Pusat Bandar Puchong,
47160 Puchong, Selangor, Malaysia.
MTM Precision supplies gas detection and industrial testing equipment throughout Selangor, Kuala Lumpur, Johor, Penang, Melaka, Negeri Sembilan, Perak, Pahang, Kedah, Perlis, Terengganu, Sarawak and Sabah, Malaysia.
17 Sep 2026
