DITRON 102 & 105 Series Stainless Steel Vernier Calipers | 150mm, 200mm & 300mm Malaysia
DITRON 102 and 105 Series Stainless Steel Vernier Calipers
The DITRON 102 and 105 series are mechanical vernier calipers with stainless steel monoblock construction. Both series support outside, inside, step and depth measurement and are available in 150mm, 200mm and 300mm measuring ranges.
The main difference shown in the catalogue is the thumb-control design. The 102 series features a round thumb control, while the 105 series features an integral thumb-push design.
These calipers provide a battery-free option for dimensional checks in workshops, maintenance departments and technical training environments in Malaysia.
PRODUCT HIGHLIGHTS
• Stainless steel construction.
• Monoblock design.
• Mechanical main scale and vernier readout.
• No battery or charging required.
• Outside, inside, step and depth measurement.
• Listed model resolution: 0.02mm.
• Choice of 150mm, 200mm and 300mm measuring ranges.
• Alternative thumb-control designs across the two series.
102 SERIES — ROUND THUMB CONTROL
The DITRON 102 series features stainless steel monoblock construction and a round thumb control for moving the slider.
Measurements are read directly from the main scale and vernier scale. Users should be familiar with vernier reading and correct measuring technique.
Available models:
DITRON 102-150
Measuring range: 0–150mm
Listed resolution: 0.02mm
Catalogue-stated accuracy: ±0.02mm
DITRON 102-200
Measuring range: 0–200mm
Listed resolution: 0.02mm
Catalogue-stated accuracy: ±0.03mm
DITRON 102-300
Measuring range: 0–300mm
Listed resolution: 0.02mm
Catalogue-stated accuracy: ±0.04mm
105 SERIES — INTEGRAL THUMB-PUSH DESIGN
The DITRON 105 series features stainless steel monoblock construction with an integral thumb-push design.
It offers an alternative way to position the slider while retaining the same catalogue-stated measuring ranges, resolution and accuracy as the corresponding 102 models.
Available models:
DITRON 105-150
Measuring range: 0–150mm
Listed resolution: 0.02mm
Catalogue-stated accuracy: ±0.02mm
DITRON 105-200
Measuring range: 0–200mm
Listed resolution: 0.02mm
Catalogue-stated accuracy: ±0.03mm
DITRON 105-300
Measuring range: 0–300mm
Listed resolution: 0.02mm
Catalogue-stated accuracy: ±0.04mm
102 VS 105 — WHICH SERIES SHOULD YOU CHOOSE?
Choose the 102 series if you prefer the round thumb-control arrangement shown in the catalogue.
Choose the 105 series if you prefer an integral thumb-push design.
Both series have the same catalogue-stated measuring performance at corresponding sizes. Select according to handling preference, measuring range and the required scale configuration.
SCALE CONFIGURATIONS
The catalogue description mentions 0.02mm and 0.05mm options, together with metric and inch scale availability.
However, the model tables on the supplied page list 0.02mm resolution for all six models.
When requesting a quotation, specify:
• Required model and measuring range.
• Required vernier graduation: 0.02mm or 0.05mm.
• Metric-only or metric/inch scale requirements.
Alternative scale configurations and their corresponding accuracy should be confirmed before ordering.
CHOOSING THE MEASURING RANGE
150mm Models
Suitable for smaller components, fasteners and routine dimensional checks within a 150mm capacity.
200mm Models
Provide additional opening capacity for components that exceed a 150mm measuring range.
300mm Models
Provide up to 300mm measuring capacity for larger workpieces. Check jaw reach and access around the component before selecting.
Choose according to the largest dimension being measured and the required tolerance. A larger range does not mean higher accuracy.
FOUR MEASUREMENT FUNCTIONS
Outside Measurement
Use the external jaws to measure accessible dimensions such as width, thickness and outside diameter.
Inside Measurement
Use the internal jaws to check accessible internal dimensions. Position and align the jaws carefully.
Step Measurement
Use the step measuring faces to check suitable stepped features.
Depth Measurement
Use the depth rod to measure accessible holes or recesses. Keep the reference face correctly seated against the workpiece.
APPLICATIONS IN MALAYSIA
The DITRON 102 and 105 series can be considered for:
• General workshop measurements.
• Machining and fabrication checks.
• Maintenance and spare-part measurements.
• Incoming component inspection.
• Assembly dimensional checks.
• Technical training in vernier scale reading.
For users in Selangor, Kuala Lumpur, Johor and Penang, selection should consider measuring range, workpiece tolerance and the operator’s ability to read the vernier scale consistently.
VERNIER CALIPER OR DIGITAL CALIPER?
A vernier caliper provides a mechanical scale readout without batteries. It suits users who are comfortable reading the main scale and vernier graduations.
A digital caliper provides a direct numerical display, which can make repeated readings easier to obtain.
Choose according to the working method and required specification. Battery-free operation does not by itself establish better accuracy or suitability for every environment.
RESOLUTION AND ACCURACY
The listed 0.02mm resolution describes the vernier reading increment. Accuracy is a separate specification.
Catalogue-stated accuracy for the listed models:
0–150mm: ±0.02mm
0–200mm: ±0.03mm
0–300mm: ±0.04mm
Results also depend on scale reading, jaw alignment, measuring force, temperature, cleanliness and instrument condition.
BASIC MEASURING PROCEDURE
1. Clean the measuring faces and workpiece.
2. Close the jaws gently and check the zero alignment.
3. Position the correct measuring faces against the workpiece.
4. Apply light, consistent measuring force.
5. Read the main scale and identify the aligned vernier graduation.
6. View the scale squarely to reduce reading error.
7. Repeat the measurement to check consistency.
Avoid forcing the jaws against the component or using the caliper as a clamp.
CARE AND STORAGE
• Remove chips and residue before closing the jaws.
• Keep the scale and sliding surfaces clean.
• Avoid measuring hot or moving components.
• Clean and dry the caliper after use.
• Follow the manufacturer’s maintenance instructions.
• Store the instrument where the measuring faces are protected.
• Check performance against suitable reference standards according to your quality procedure.
FREQUENTLY ASKED QUESTIONS
Do the DITRON 102 and 105 require batteries?
No. They are mechanical vernier calipers.
What is the main difference between the two series?
The 102 has a round thumb control, while the 105 has an integral thumb-push design.
Are both series made from stainless steel?
Yes. The catalogue describes stainless steel monoblock construction.
What resolution is listed?
The model tables list 0.02mm for all six models.
Is a 0.05mm version available?
The catalogue description mentions a 0.05mm option. Confirm availability, model configuration and accuracy before ordering.
Are metric and inch scales available?
The catalogue mentions metric and inch scale availability. Specify the required configuration when requesting a quotation.
Can these calipers measure depth?
Yes. Outside, inside, step and depth measurement are listed.
Is the 105 more accurate than the 102?
No. The catalogue lists the same accuracy for corresponding measuring ranges.
Can a vernier caliper be used for tight-tolerance inspection?
Assess the required tolerance against the instrument’s accuracy and your inspection procedure. A micrometer or another measuring instrument may be more appropriate.
Is a calibration certificate included?
The supplied page does not confirm that an individual calibration certificate is included. Specify documentation requirements when requesting a quotation.
SEO META DESCRIPTION
Explore DITRON 102 and 105 stainless steel vernier calipers in Malaysia. Compare 150mm, 200mm and 300mm models with listed 0.02mm resolution.
ENQUIRE ABOUT DITRON VERNIER CALIPERS
Contact MTM Precision with your preferred series, measuring range and quantity. Please specify the required vernier graduation, metric or metric/inch scale configuration, and any calibration documentation requirements.
Availability, scale options and supplied accessories are subject to confirmation.
MTM Precision Sdn Bhd
Showroom & Service Centre: No. 29-1 & 29-2, Jalan Bandar 18, Pusat Bandar Puchong, 47160 Puchong, Selangor, Malaysia
Tel: 03-8080 7172
WhatsApp: +6016-660 7346
Email: mtmpre@yahoo.com
Website: www.mtmpre.com.my
24 Oct 2026
