DITRON Magnetic Stands for Dial Indicators | DR Series Selection Guide Malaysia
Choosing a Magnetic Stand for Stable Indicator Measurements
DITRON DR Series Magnetic Stands support dial indicators, digital indicators and compatible measuring instruments during inspection and alignment work.
The catalogue lists an aluminium alloy arm, a switchable magnetic base, an 8mm clamp hole and an M8 x 1.25mm tapping hole. An optional 3/8-inch clamp configuration is also mentioned.
For machining workshops and maintenance teams in Malaysia, selection should consider instrument compatibility, required reach, mounting surface and rigidity.
A stable stand is essential because movement in the holder can appear as movement of the workpiece.
KEY FEATURES
Switchable Magnetic Base
The On/Off switch allows the magnetic base to be attached to and released from a suitable ferromagnetic surface.
Check that the base seats securely before positioning the measuring instrument.
Aluminium Alloy Arm
The catalogue specifies an aluminium alloy arm. The illustrated articulated arrangement allows the indicator to be positioned around the workpiece.
8mm Clamp Hole
An 8mm clamp hole is listed for compatible instrument stems or adapters.
Confirm the actual mounting arrangement before purchase. A lever indicator may require an appropriate adapter rather than direct stem clamping.
Optional 3/8-Inch Clamp
The catalogue mentions an optional 3/8-inch clamp configuration. Specify the required size when requesting a quotation.
M8 x 1.25mm Tapping Hole
An M8 x 1.25mm tapping hole is listed. Confirm its location and function against the selected model’s drawing if it is needed for an installation.
DR SERIES CATALOGUE SPECIFICATIONS
The following values reproduce the model table. Magnetic force is shown in the catalogue’s kg notation and should not be interpreted as an allowable suspended load.
Model: DR-200-F
Listed stem length: 200mm
Listed magnetic force: 30kg
Model: DR-280
Listed stem length: 280mm
Listed magnetic force: 50kg
Model: DR-320
Listed stem length: 320mm
Listed magnetic force: 60kg
Model: DR-345
Listed stem length: 345mm
Listed magnetic force: 80kg
Model: DR-370
Printed stem length: 270mm
Listed magnetic force: 100kg
Model: DR-470
Listed stem length: 470mm
Listed magnetic force: 120kg
The DR-370 row prints 270mm, which differs from the number in the model designation. Confirm the correct length before ordering.
The general feature text also states 80kg magnetic force, while the model table lists different values. Use the model-specific figures for initial comparison and confirm the selected configuration.
HOW TO SELECT THE CORRECT STAND
Check the Instrument Mount
Provide the indicator model, stem diameter and mounting style. Confirm whether an adapter is required and whether it is included.
Choose Sufficient Reach
Select enough arm length to reach the measuring point while keeping the setup compact.
The catalogue’s stem length is not a guaranteed horizontal reach or working height. Actual positioning depends on the arm arrangement, joints and holder.
Prioritise Rigidity
A longer arm can provide access but may be more sensitive to movement when extended.
Position the base close to the measuring location where practical, minimise unnecessary extension and secure all joints.
Assess the Mounting Surface
The base requires a suitable magnetic surface. Holding performance depends on material, thickness, flatness, cleanliness and contact area.
Paint, rust, chips, curvature and gaps can reduce attachment strength. Do not assume that every steel surface provides the listed holding performance.
Understand the Magnetic Force Figure
The listed magnetic force is not the indicator payload capacity or the permitted side load at the end of an extended arm.
The supplied page does not state the test conditions or allowable arm loading. Confirm these details for demanding installations.
TYPICAL APPLICATIONS
Dial Indicator Runout Checks
Support an indicator while checking a component held in a suitable rotational inspection fixture.
Machine Setup and Alignment
Position a compatible indicator against an accessible surface during controlled setup work.
Comparative Inspection
Hold the instrument at a reference position while comparing similar components.
Maintenance Movement Checks
Support an indicator when checking relative movement or clearance in a suitably restrained assembly.
These applications are relevant to workshops in Selangor, Penang, Johor and other industrial areas in Malaysia.
BASIC SETUP WORKFLOW
1. Prepare the mounting surface.
Remove chips and residue. Check that the base can sit fully against the surface.
2. Position and engage the base.
Place the stand near the measurement point and operate the magnetic switch according to the instructions.
3. Fit the indicator.
Use the correct clamp or adapter. Secure the instrument without excessive clamping force.
4. Arrange the arm.
Keep the position compact and provide clearance from the component and surrounding equipment.
5. Secure the joints.
Check that tightening does not shift the probe away from the intended measurement point.
6. Establish the reference.
Set up the indicator and repeat the measurement cycle to assess stability.
COMMON CAUSES OF UNSTABLE READINGS
Incomplete base contact.
Chips, rust or paint beneath the base.
Loose joints or instrument clamps.
Excessive arm extension.
Vibration or movement of the mounting surface.
Incorrect probe alignment or contact force.
Check the complete support arrangement before assuming that the indicator is faulty.
CARE AND HANDLING
Support the arm and instrument before releasing the magnetic base. Keep the base clean and avoid dragging trapped chips across a reference surface.
Do not use an indicator stand as a lifting magnet. Protect the joints and clamps from impact, and store the assembly with the instrument secured.
FREQUENTLY ASKED QUESTIONS
What instruments can these stands hold?
They can support compatible indicators and measuring instruments, subject to the clamp size, mounting style and required adapter.
What clamp size is listed?
The catalogue lists 8mm, with an optional 3/8-inch configuration.
Does the base have an On/Off switch?
Yes. A switchable magnetic base is specified.
Does 80kg magnetic force mean an 80kg payload?
No. Magnetic holding force is different from allowable instrument loading, especially with an extended arm.
Can it attach directly to aluminium?
A magnetic base does not attach directly to an aluminium surface. A suitable ferromagnetic mounting arrangement is needed.
What is the DR-370 arm length?
The supplied table prints 270mm. Confirm the correct dimension before ordering.
Is an indicator included?
The supplied page does not confirm an included indicator. Specify the required stand, instrument and adapters in the quotation.
SEO META DESCRIPTION
Explore DITRON DR magnetic stands in Malaysia. Compare listed arm lengths, magnetic force, 8mm clamps and mounting needs for dial and digital indicators.
CONTACT MTM PRECISION
Contact MTM Precision with your indicator model, required reach and mounting surface details for assistance selecting a DITRON DR Series Magnetic Stand.
MTM Precision Sdn Bhd
Showroom & Service Centre: No. 29-1 & 29-2, Jalan Bandar 18, Pusat Bandar Puchong, 47160 Puchong, Selangor, Malaysia
Tel: 03-8080 7172
WhatsApp: +6016-660 7346
Email: mtmpre@yahoo.com
Website: www.mtmpre.com.my
25 Oct 2026
