2
Share:
Tohnichi ST3-G/ST3-G-BT Rotary peak torque measuring equipment
Brand: Tohnichi
Category:
Welding Tools
Specifications
SKU: Tohnichi ST3-G/ST3-G-BT Rotary peak torque measuring equipment
Simple torque checks and angle checks are possible without removing nutrunners from multi-spindle tightening equipment. Also useful for rotation angle tightening.
Spintork® ST15N3-6.35-GοΌOverall length=106.5 mm)
Spintork® ST50N3-3/8-G (Overall length=75 mm)
Spintork® ST1000N3-G-BT (Overall length=135 mm)
Example of a multi-spindle device in use
The ST3-G-BT now supports dual-mode Bluetooth® profiles: SPP and GATT. Dual-mode products can be identified by the label above.
Application
- Checks nutrunner torque and angle on multi-spindle tightening equipment.
- The ST3-G-BT series is especially useful for checking torque and angle for rotation angle tightening of a plastic region.
- Often used to good effect as a measuring device (standard accessory) for multi-spindle equipment nutrunners.
- Checks the torque and angle of angle power tools and hand nutrunners.
- The ST1000N3-G model is ideal for torque checking (daily check) of TW2 series of torque wrenches used to tighten the wheel nuts of large vehicles, and the DQLE1000N2.
Features
- Digital torque checkers. The world’s most compact rechargeable rotary torque measuring equipment.
- Nutrunner torque checks (routine inspections) can prevent the production of imperfectly tightened items.
- Allows operators to perform torque checks (daily check) of multi-spindle tightening equipment while tightening at the same time. Connect the optional extension bar, which has the same length as the ST3-G, to spindles not installed with Spintork® to check torque easily without removing the nutrunner from multi-spindle tightening equipment. This reduces steps in the manufacturing process.
- Nutrunner inline measurement is possible. If the model is Bluetooth® equipped, torque checking can be cordless, improving workability.
- ST3-G is equipped with an angle sensor. If tightening is done with a handheld nutrunner attached to the ST3-G, torque checking and angle checking can be done at the same time as tightening operations. (* Note: Angle measurements are measurements from set snug torque values.)
- When the supplied USB connecting cable is connected to a computer, tightening torque and angle data measured using an ST3-G can be spread and controlled in Excel format using DtRcv. (DtRcv can be downloaded free of charge.)
- The ST3-G-BT can be used to create torque and angle graphs. With a Bluetooth®-equipped ST3-G-BT, torque and angle values can be measured and recorded continuously, and tightened-to-completion data is transmitted wirelessly to a computer. Then, after DtRcv spreads the data on an Excel file, graphs displaying tightening torque and angle values can be created. (* Note: You need to have your own software for Bluetooth® signal reception. * When the ST3-G is not the -BT version, memory stores only maximum torque data and that-moment angle data, and graphs cannot be created.)
- Bit types and small sq. drive models have been added to the lineup. Newly added: ST15N3-6.35-G, which can be attached to Hex 6.35 bit tools (not available on older ST2 series), and ST50N3-3/8-G 9.53 mm square drive (smaller than previous version).
- Capable of managing both wired and wireless (Bluetooth®) tightening data. *Use Excel® on your computer to manage data received via DtRcv (Data Receiver). DtRcv is included in software under the screen.
- ST3-G-BT conforms to telecommunication standards in Japan, the US, Canada, the EU, Thailand, Mexico, Vietnam, Brazil, Taiwan, China, Singapore, South Korea, Russia, and Malaysia (information valid as of March 2026).
Specifications
[Nο½₯m] |
||||||||||
[cNο½₯m] |
||||||||||
[kgfο½₯cm] |
||||||||||
[kgfο½₯m] |
||||||||||
[lbfο½₯in] |
||||||||||
[lbfο½₯ft] |
||||||||||
[ozfο½₯in] |
||||||||||
[mm] |
||||||||||
Memory count value: 3 digits (character height: 3 mm), Torque/rotating angle display: 4 digits(character height: 7 mm) Unit, Remaining battery capacity, Measurement direction |
||||||||||
Notes
-
ST3-G-BT external output connector cannot be used.
-
The Spintork® ST3 series cannot be used when connected to an impact wrench. (Damage to electronic parts could cause equipment failure and inaccuracy.)
-
Japan’s Measurement Law prohibits ST3-G / ST3-G-BT series devices from being used in Japan or sold for use in Japan.
-
Bluetooth® is a registered trademark of Bluetooth SIG, Inc.
-
Excel® is a registered trademark of Microsoft Corporation.
Standard accessory
Quick battery charger BC-4-2, power source conversion plug, power source plug for long-term storage, carrying case, instruction manual, USB connecting cable (No.384; not supplied for –BT models), calibration certificate
Untitled
Inquiry - Tohnichi ST3-G/ST3-G-BT Rotary peak torque measuring equipment
