Wintact WT-100A Ultrasonic Thickness Gauge for Ship and Marine Maintenance Malaysia
Wintact WT-100A Ultrasonic Thickness Gauge for Ship and Marine Maintenance Malaysia
Copy Link
Ships, workboats, barges and other marine structures operate continuously in environments where corrosion and material deterioration are important maintenance concerns. Steel plates, piping and other accessible metal components can gradually lose thickness due to long-term exposure and operating conditions.
The Wintact WT-100A Ultrasonic Thickness Gauge provides a portable, non-destructive method for measuring the remaining thickness of suitable materials without cutting the component.
For shipyards, marine engineering companies and maintenance teams in Malaysia, ultrasonic thickness measurement can be a useful tool for routine condition monitoring and maintenance work.
Why Is Thickness Measurement Important in Marine Maintenance?
Marine equipment can be exposed to conditions that contribute to material deterioration, including:
Saltwater
High humidity
Internal and external corrosion
Weather exposure
Mechanical wear
Chemical exposure
Long-term operation
A steel surface may still appear structurally intact while its remaining thickness has changed.
Ultrasonic thickness testing provides an actual thickness reading that can complement visual inspection.
Where Can the WT-100A Be Used?
Depending on the material, surface condition, accessibility and inspection requirements, ultrasonic thickness measurements may be considered for suitable areas such as:
Steel plates
Marine piping
Tanks
Deck structures
Bulkheads
Fabricated steel components
Machinery-related metal parts
Other accessible homogeneous materials
For formal vessel surveys or classification work, measurements and acceptance criteria must follow the applicable requirements and be performed by appropriately qualified or approved personnel where required.
Measure from One Accessible Side
One major advantage of ultrasonic thickness measurement is that suitable materials can generally be measured from one accessible side.
This is useful when technicians cannot conveniently access the opposite side of a steel plate or pipe.
A typical measurement process may include:
Identify the measurement location.
Clean and prepare the surface.
Configure the instrument for the material.
Apply suitable ultrasonic couplant.
Place the probe correctly on the surface.
Obtain a stable reading.
Record the thickness and measurement location.
Repeat at other inspection points.
Surface condition, coatings, corrosion, geometry and measurement technique can influence results and should be considered when planning the inspection.
Useful for Marine Corrosion Monitoring
Instead of taking random measurements, maintenance teams can establish repeatable measurement points.
For example:
Location A: Previous 8.20 mm → Current 8.05 mm
Location B: Previous 8.10 mm → Current 7.92 mm
Location C: Previous 8.15 mm → Current 7.30 mm
Location C shows a larger change and may warrant closer investigation.
This illustrates why historical thickness data can be more valuable than a single isolated measurement.
Applications in Malaysia's Marine Sector
Ultrasonic thickness measurement may be relevant to:
Shipyards
Marine engineering companies
Vessel maintenance contractors
Port maintenance operations
Barge operators
Workboat operators
Fabrication companies
Marine equipment maintenance
Offshore support operations
Industrial maintenance companies
Can WT-100A Be Used for Ship Hull Inspection?
The WT-100A can provide ultrasonic thickness measurements on suitable materials and under appropriate measurement conditions.
However, a portable thickness gauge should not automatically be considered a substitute for a formal ship hull survey.
Classification, statutory or safety-critical inspections may require approved procedures, calibrated equipment, qualified operators, specified measurement locations and acceptance criteria established by the relevant authority or classification society.
For general maintenance and preliminary thickness monitoring, however, a portable ultrasonic thickness gauge can be a useful instrument.
Why Marine Companies Should Track Thickness Over Time
The objective should not only be:
“What is the thickness today?”
A better maintenance question is:
“How has the thickness changed since the previous inspection?”
When the same locations are measured consistently, maintenance teams can build a condition history:
Measure → Record → Compare → Identify Wall Loss → Investigate → Plan Maintenance
This approach can support more informed preventive maintenance decisions.
Portable Thickness Measurement for Field Work
Marine maintenance often requires technicians to move between different inspection locations.
A portable ultrasonic thickness gauge such as the Wintact WT-100A is therefore practical for technicians who need a compact instrument for field measurements, workshop inspections and routine maintenance checks.
Looking for an Ultrasonic Thickness Gauge in Malaysia?
MTM Precision supplies ultrasonic thickness gauges and industrial testing instruments for engineering, fabrication, maintenance and inspection applications throughout Malaysia.
If you need to measure steel plate, piping, tank or other suitable material thickness, MTM Precision can assist in selecting an appropriate instrument based on your application requirements.
Contact MTM Precision
MTM Precision Sdn. Bhd.
Showroom & Service Centre
No. 29-1 & 29-2, Jalan Bandar 18,
Pusat Bandar Puchong,
47160 Puchong, Selangor, Malaysia
🌐 Website: www.mtmpre.com.my
📧 Email: mtmpre@yahoo.com
📱 WhatsApp: +6016-660 7346
10 Aug 2026
