How to Store Concrete Cube Moulds Properly? Plastic & Cast Iron Storage Guide Malaysia
How to Store Concrete Cube Moulds Properly? Plastic & Cast Iron Storage Guide Malaysia
Introduction
Concrete Cube Moulds are reusable testing equipment, but their condition depends not only on how they are used.
Storage also matters.
A Cube Mould may be handled correctly during concrete specimen preparation but still become damaged because it is:
Thrown into a vehicle after use
Stored while covered with concrete residue
Left outdoors
Placed under heavy equipment
Stored wet for long periods
Mixed together with damaged moulds
For contractors, ready-mix concrete companies, precast manufacturers, and testing laboratories that own many Cube Moulds, proper storage can help protect equipment and simplify stock control.
At MTM Precision Sdn. Bhd., we supply Plastic and Cast Iron Concrete Cube Moulds for concrete testing applications throughout Malaysia.
Why Does Cube Mould Storage Matter?
Cube Moulds are used to form concrete specimens.
Their condition therefore matters.
Poor storage can contribute to:
Plastic mould distortion
Cracking
Impact damage
Cast iron corrosion
Damaged fasteners
Lost components
Concrete build-up
Difficulty locating usable moulds
A good storage system does not need to be complicated.
The objective is simply to keep moulds clean, protected, identifiable, and ready for the next use.
Clean Before Storage
Do not make storage the first step after demoulding.
A better workflow is:
Demould → Clean → Inspect → Dry as Required → Store
Concrete residue becomes more difficult to remove after it hardens.
Cleaning before storage also makes the next inspection easier.
Don't Store Dirty Cube Moulds with Clean Ones
A common problem in busy site operations is mixing:
Used / Dirty Moulds
with
Clean / Ready Moulds
Once everything is in one pile, technicians may not know which units are ready for the next concrete pour.
Create separate areas whenever practical.
Simple Storage Zones
A useful system can have three areas:
READY FOR USE
Clean and inspected moulds.
RETURNED / TO BE CLEANED
Moulds coming back from testing work.
HOLD / INSPECTION
Moulds with cracks, distortion, corrosion, damaged fasteners, or other concerns.
This simple separation can prevent many operational mistakes.
How to Store Plastic Concrete Cube Moulds
Plastic Cube Moulds are lightweight and corrosion resistant, but they should still be protected from unnecessary physical stress.
Good storage practices include:
Keep them clean
Store in an organised area
Protect them from impact
Avoid excessive loads on top
Keep damaged units separate
Avoid uncontrolled exposure to severe conditions
The exact storage arrangement depends on mould design and quantity.
Don't Put Heavy Equipment on Plastic Cube Moulds
Plastic moulds should not become shelves for other equipment.
Avoid placing heavy items such as:
Steel tools
Toolboxes
Cast Iron Cube Moulds
Heavy machine parts
Construction materials
on top of Plastic Cube Moulds.
Long-term loading or impact can potentially damage or distort the mould.
Avoid Throwing Plastic Moulds into a Storage Pile
Plastic Cube Moulds may look robust, but repeated impact can eventually cause damage.
Instead of throwing moulds into a large pile after cleaning, place them in an organised storage location.
This is particularly important for ready-mix companies where moulds may be handled every day.
How to Store Cast Iron Concrete Cube Moulds
Cast Iron Cube Moulds have different storage priorities.
Important considerations include:
Cleaning
Drying
Corrosion prevention
Fastener condition
Organised storage
Cast Iron Moulds should not remain wet unnecessarily after cleaning.
Moisture Is Important for Cast Iron
Malaysia has a humid climate.
Cast Iron equipment exposed to moisture can develop corrosion if it is not properly maintained.
After cleaning, follow the appropriate maintenance procedure before placing the mould into storage.
Pay attention to:
Internal surfaces
Joints
Bolts
Threads
Contact surfaces
Don't Store Cast Iron Moulds Outdoors Unnecessarily
A Cast Iron Cube Mould repeatedly exposed to:
Rain
Water
High humidity
Outdoor contamination
may require more maintenance.
Where practical, keep laboratory moulds in a suitable protected storage area.
Check Fasteners Before Storage
For multi-piece Cast Iron Cube Moulds, inspect:
Bolts
Nuts
Threads
Clamping components
If components are loose and separated carelessly, they can easily become lost.
A mould body without its required fastening components may be unusable when urgently needed.
Keep Components Together
If a mould has dedicated components, organise them so that one complete mould remains identifiable as one set.
Avoid creating a situation where:
20 mould bodies
are stored in one area while:
40 unidentified bolts
are lying somewhere else.
Organisation reduces unnecessary downtime.
Should Cube Moulds Be Stored Assembled or Disassembled?
This depends on:
Mould design
Manufacturer instructions
Available space
Laboratory procedure
Frequency of use
There is no universal storage method suitable for every Cube Mould.
The important point is that storage should not damage the mould or cause components to be lost.
Storage for Ready-Mix Concrete Companies
Ready-mix companies may have Cube Moulds constantly moving between:
Plant → QC Vehicle → Customer Site → Plant
This makes storage more complicated than in a fixed laboratory.
A useful system is to distinguish between:
Plant Stock
Vehicle Stock
Site / Issued Stock
Spare Stock
Now the QC department knows where its moulds are supposed to be.
Give Each QC Vehicle Its Own Mould Stock
For companies with several mobile testing teams, consider allocating moulds to each vehicle.
For example:
QC VAN 1
20 Plastic Cube Moulds
QC VAN 2
20 Plastic Cube Moulds
QC VAN 3
20 Plastic Cube Moulds
PLANT SPARE
20 Plastic Cube Moulds
This can reduce constant borrowing between teams.
Secure Moulds During Vehicle Transportation
Vehicle storage is still storage.
Moulds should not move freely around the vehicle every time it brakes or turns.
Repeated impact with:
Slump Cone
Steel tools
Tamping Rod
Toolboxes
Other equipment
can damage products over time.
Organise the vehicle equipment area whenever practical.
Plastic Cube Moulds Are Useful for Mobile Storage
One reason Plastic Cube Moulds are practical for ready-mix and contractor vehicles is their lower weight.
A mobile testing vehicle may carry multiple moulds together with:
Slump Cone
Base Plate
Tamping Rod
Measuring Equipment
PPE
Plastic helps reduce the overall equipment load.
Storage for Construction Contractors
Contractors may have temporary site laboratories or equipment stores.
Cube Mould storage should be located where technicians can access the moulds easily without exposing them unnecessarily to construction damage.
Avoid storing moulds:
Under heavy construction materials
In vehicle traffic areas
Mixed with general site debris
Where other workers may use them as containers
Cube Moulds are testing equipment—not general-purpose boxes.
Don't Use Cube Moulds to Store Tools
This is especially tempting with Plastic Cube Moulds.
Their shape makes them look like convenient containers.
Do not routinely fill them with:
Bolts
Nails
Hand tools
Steel parts
These items can scratch or damage the internal specimen-forming surfaces.
Storage for Precast Factories
A precast factory can establish a dedicated Cube Mould area near the QC or specimen preparation section.
A practical workflow may be:
Clean Stock
↓
Issued for Testing
↓
Demoulding
↓
Cleaning
↓
Inspection
↓
Return to Clean Stock
Damaged moulds leave the normal circulation.
Storage for Material Testing Laboratories
Laboratories may benefit from more formal identification.
Separate moulds according to:
Size
Material
Status
For example:
100mm Plastic
150mm Plastic
100mm Cast Iron
150mm Cast Iron
This reduces selection mistakes.
Never Mix 100mm and 150mm Without Identification
A busy store may contain dozens of Cube Moulds.
If different sizes are mixed together, technicians can accidentally select the wrong product.
Clear shelf labels or storage zones make the difference obvious.
Separate Plastic and Cast Iron Stock
Material separation can also be useful.
For example:
Rack A – Plastic Cube Mould
Rack B – Cast Iron Cube Mould
This makes inventory counting and equipment allocation easier.
Keep New Spare Stock Separate
Customers who purchase replacement moulds in advance can maintain a dedicated:
NEW / SPARE STOCK
area.
Do not unnecessarily put every new mould into daily circulation immediately.
When an operating mould is removed from service, a spare can replace it.
Why Spare Stock Should Be Protected
Spare moulds are supposed to solve future shortages.
If spare stock becomes damaged before it is even used, it defeats the purpose.
Keep replacement inventory protected and clearly identified.
Use FIFO if It Helps Your Operation
Some companies may choose a simple stock rotation method.
Instead of always taking the newest mould, the QC department can manage equipment according to its own identification and inspection system.
The objective is not necessarily strict warehouse FIFO.
The objective is to know:
Which moulds are in use?
Which are spare?
Which need inspection?
Conduct Periodic Stock Counts
For companies with many moulds, perform occasional stock checks.
Count:
Ready for Use
In Use / Issued
Spare
Damaged
Missing
This can reveal losses before the next urgent project.
Example Cube Mould Stock Check
A ready-mix company records:
Total Purchased: 100
Plant Ready Stock: 25
QC Vehicles: 50
Under Inspection: 5
Damaged: 8
Unable to Locate: 12
The company now knows that its real usable stock is much lower than the original purchase quantity.
Missing Moulds Are Also a Purchasing Cost
Not every replacement is caused by physical wear.
Cube Moulds may be lost because they are:
Left at customer sites
Moved between projects
Mixed with contractor equipment
Stored without identification
Better storage and tracking can therefore reduce replacement costs.
Label Your Moulds
For larger organisations, simple identification can help.
For example:
MTM READY-MIX QC
PCM-001
or:
PROJECT A
150MM-012
The exact system is up to the company.
The important thing is that the mould can be traced.
Check Storage Before Buying More Moulds
Sometimes a company thinks it needs to buy more Cube Moulds because technicians cannot find enough.
Before ordering, check:
Main store
QC vehicles
Site laboratories
Cleaning area
Inspection area
Other active projects
The problem may be poor stock control rather than insufficient total quantity.
But Don't Delay Replacement When Stock Is Truly Low
After the stock check, calculate the usable quantity.
Damaged moulds should not be counted as normal available stock.
If usable inventory is below operational requirements, replenish before a shortage affects testing work.
Slump Cone Storage Should Also Be Organised
The same principle applies to related concrete testing equipment.
A site testing area may contain:
Cube Moulds
Slump Cone
Tamping Rod
Base Plate
Measuring Accessories
Keeping these products together in an organised testing-equipment area makes preparation easier.
One Testing Equipment Area per Site
For larger contractors, each project can maintain its own concrete testing equipment area.
This reduces unnecessary movement between sites and makes responsibility clearer.
When the next concrete pour is scheduled, the site team already knows where its equipment is.
Storage Is Part of Equipment Cost Control
A company can purchase good equipment and still waste money through poor storage.
The real cost of a Cube Mould includes:
Purchase + Handling + Storage + Maintenance + Replacement
Protecting equipment after use can help reduce unnecessary repeat purchases caused purely by damage or loss.
Need Additional or Replacement Cube Moulds?
Even with good storage, Cube Moulds will eventually require replenishment as testing volume changes and individual units are removed from service.
MTM Precision supplies:
Plastic Concrete Cube Moulds
Cast Iron Concrete Cube Moulds
100mm Cube Moulds
150mm Cube Moulds
Customers can contact us for:
New requirements
Bulk quantities
Spare stock
Replacement moulds
Repeat orders
Why Choose MTM Precision?
MTM Precision supplies practical Concrete Testing Equipment for:
Contractors
Ready-Mix Concrete Companies
Precast Manufacturers
Material Testing Laboratories
Universities
Civil Engineering Companies
QA/QC Teams
Our key compact concrete testing product groups include:
Concrete Cube Mould
Slump Cone
Concrete Test Hammer
For repeat customers, keeping the previous mould type and size on record can make future replacement orders faster and easier.
Contact MTM Precision
MTM Precision Sdn. Bhd.
Showroom & Service Centre
No. 29-1 & 29-2, Jalan Bandar 18,
Pusat Bandar Puchong,
47160 Puchong, Selangor, Malaysia
Website: www.mtmpre.com.my
Email: mtmpre@yahoo.com
WhatsApp: +6016-660 7346
SEO Keywords
How to Store Concrete Cube Mould Malaysia, Plastic Cube Mould Storage Malaysia, Cast Iron Cube Mould Storage Malaysia, Concrete Cube Mould Maintenance Malaysia, Concrete Cube Mould Supplier Malaysia, Ready Mix Cube Mould Malaysia, 100mm Cube Mould Malaysia, 150mm Cube Mould Malaysia, Concrete Testing Equipment Storage Malaysia, Slump Cone Malaysia.
14 Aug 2026