Which Total Station Can Use Myzox TK-10S TK-10 Monitoring Prism Malaysia
Which Total Station Can Use Myzox TK-10S / TK-10 Monitoring Prism?
A common question when selecting the Myzox TK-10S / TK-10 Monitoring Prism L-Bar Type is whether it can be used with an existing total station.
Because the TK-10S / TK-10 is a passive optical prism target, compatibility is primarily determined by the total station's prism EDM capability, prism constant settings, observation conditions and required monitoring performance rather than simply by matching the brand name printed on the instrument.
This means surveyors using different professional total station brands may be able to use the Myzox monitoring prism when the equipment is correctly configured and suitable for the intended application.
For professional monitoring work, always verify the specific total station configuration and project requirements before establishing baseline measurements.
MTM Precision Sdn. Bhd. is an authorized distributor of Myzox in Malaysia.
Quick Answer
Can Myzox TK-10S / TK-10 Be Used with Other Total Station Brands?
Potentially, yes.
The monitoring prism is not electronically paired with a particular total station brand.
The important factors include:
Prism measurement capability
Prism constant setting
EDM performance
Observation distance
Target orientation
Required accuracy
Monitoring methodology
The Myzox TK-10S / TK-10 has a specified prism constant of -25 mm.
The corresponding setting should be configured according to the total station manufacturer's procedures.
Myzox TK-10S / TK-10 Key Specifications
SpecificationDetailsModelsTK-10S / TK-10Product TypeMonitoring Prism L-Bar TypePrism Diameter1 inch / 25 mmPrism Constant-25 mmPrism Height60 mmBeam Deviation5″DimensionsH90 × W86.5 × D30 mmWeightApprox. 207 gAdjustmentX/Y Direction
These specifications should be considered when planning the total station monitoring setup.
Can Myzox Monitoring Prism Be Used with Topcon Total Station?
A Myzox monitoring prism may be used as an optical target with a suitable Topcon total station when the measurement configuration and project requirements are compatible.
Important considerations include:
Correct prism constant
Prism measurement mode
Observation distance
Total station accuracy
EDM capability
Required monitoring performance
The -25 mm prism constant should be correctly handled according to the applicable total station operating procedure.
Can It Be Used with Sokkia Total Station?
The same general principle applies to suitable Sokkia total stations.
The prism itself is a passive reflector.
Surveyors should verify:
Total Station → Prism Mode → Prism Constant → Target → Measurement
Do not assume that the instrument's previous prism settings are correct simply because it was already being used with another prism.
Different prism assemblies can have different constants.
Can It Be Used with Leica Total Station?
Potential compatibility should again be evaluated according to the specific total station and measurement configuration.
Check the instrument's documentation for:
Reflector configuration
Prism constant handling
EDM measurement
Monitoring functionality where applicable
For precision monitoring, the survey team should verify the complete measurement setup before accepting baseline observations.
Can It Be Used with Trimble Total Station?
A suitable Trimble total station may also be capable of observing an appropriate third-party prism target.
The important issue is not whether the prism and total station carry the same brand.
The important issue is whether the measurement configuration is correct and suitable for the required monitoring application.
Can It Be Used with Nikon Total Station?
Where a Nikon total station supports the required prism measurement and configuration, a monitoring prism may potentially be used as the target.
Again, check:
Prism constant
EDM capability
Observation range
Instrument condition
Required measurement performance
The instrument manufacturer's procedures should take priority when configuring the total station.
Do You Need a Myzox Total Station to Use Myzox Prism?
No brand-matching assumption should be necessary simply because the target is manufactured by Myzox.
A surveying prism is fundamentally an optical reflector.
However, this does not mean every prism is automatically suitable for every total station application.
The surveyor still needs to consider the prism specification and instrument configuration.
Why Is Prism Constant So Important?
The prism constant accounts for the optical characteristics of the prism assembly.
For the Myzox TK-10S / TK-10:
Prism Constant = -25 mm
If the total station is configured for a different prism constant, a systematic distance difference can be introduced.
This can be particularly problematic for monitoring because measurements from different dates are compared.
Example: Wrong Prism Setting
Suppose a monitoring project establishes its baseline using the correct target configuration.
Later, another survey crew arrives.
They use the same prism but accidentally select a different prism setting on the total station.
The resulting measurements may show a difference.
That difference could potentially be misinterpreted as movement if the setup error is not identified.
This is why the prism constant should be included in the monitoring records.
Add Prism Information to the Monitoring Register
For every monitoring point, consider recording:
ItemExamplePoint IDMP01PrismMyzox TK-10SPrism Constant-25 mmInstallation LocationBuilding ABaselineRecordedPhotographRecordedOrientationChecked
This reduces confusion when different survey crews work on the same project.
Does Total Station Accuracy Matter?
Yes.
A monitoring prism does not determine the accuracy of the complete monitoring system.
Overall performance depends on factors including:
Total station angle accuracy
EDM specification
Observation distance
Survey geometry
Reference network
Target installation
Atmospheric conditions
Field procedures
Data processing
The required total station should therefore be selected according to the monitoring specification.
Is a 1-Second Total Station Required?
Not every monitoring project has the same accuracy requirement.
Some applications may require higher-performance instruments, while others may have different tolerances.
The correct total station specification should be determined from:
Expected movement
Required detection capability
Observation distance
Network geometry
Project monitoring specification
Do not choose an instrument solely based on the prism.
Observation Distance Matters
A total station and prism combination should be evaluated over the actual site distance.
For example:
Total Station → 30 m → Monitoring Prism
and
Total Station → 300 m → Monitoring Prism
are very different measurement situations.
Consider:
EDM performance
Atmospheric conditions
Prism orientation
Target visibility
Required accuracy
Always assess the complete measurement geometry.
Prism Orientation Matters
The target should be suitably oriented toward the total station.
The Myzox TK-10S / TK-10 provides X/Y directional adjustment, helping surveyors orient the fixed prism during installation.
This can be useful when the target is mounted on a building or structure that does not directly face the observation station.
Can One Total Station Observe Multiple Myzox Monitoring Prisms?
Yes, where the total station setup, visibility and project methodology permit it.
For example:
Total Station
→ MP01
→ MP02
→ MP03
→ MP04
→ MP05
→ MP06
This is a common concept for structural monitoring networks.
The number of targets should be determined according to the project design.
Can Myzox Monitoring Prism Be Used with Robotic Total Stations?
A fixed prism can potentially provide a target for a suitably configured robotic or monitoring total station.
However, automatic target recognition and automated monitoring performance depend on the specific instrument, target conditions and monitoring system.
Do not assume that installing a prism automatically creates an automated monitoring system.
A complete system may require:
Robotic total station
Monitoring software
Stable reference network
Communication system
Power supply
Data processing
Monitoring targets
Manual Total Station Monitoring
The Myzox monitoring prism can also be used in conventional manual workflows.
A surveyor may visit the site:
Baseline → Week 1 → Week 2 → Week 3 → Week 4
and measure the same fixed targets during each survey.
For many smaller projects, this may be simpler than installing a fully automated monitoring system.
What If You Change Total Stations During the Project?
Long monitoring projects may involve more than one instrument.
If the total station changes, document and verify:
Instrument model
Instrument accuracy
Calibration status
Prism constant
Measurement settings
Station setup
Survey methodology
Maintaining consistency is important when comparing small positional changes.
Should the Total Station Be Calibrated?
Survey instruments used for professional monitoring should be appropriately maintained and checked.
Monitoring depends on repeated measurements, so instrument condition matters.
MTM Precision provides total station calibration and surveying instrument service in Malaysia.
This includes support for professional surveying applications where reliable repeated observations are required.
Which Total Station Is Best for Monitoring?
There is no single answer for every project.
Selection depends on:
Manual or automated monitoring
Required accuracy
Observation distance
Number of targets
Monitoring frequency
Project duration
Site conditions
Budget
For simple periodic monitoring, an appropriate manual total station may be sufficient.
For frequent automated monitoring, a suitable robotic or dedicated monitoring system may be more appropriate.
Applications for Myzox Monitoring Prism
The TK-10S / TK-10 can support suitable total station monitoring applications involving:
Buildings
Deep excavation
Retaining walls
Bridges
Slopes
Tunnels
High-rise construction
MRT and railway
Highways
Infrastructure
Need Help Checking Your Total Station?
When enquiring, provide MTM Precision with:
Total Station Brand:
Topcon / Sokkia / Leica / Trimble / Nikon / Other
Model:
Your total station model
Monitoring Prism:
Myzox TK-10S / TK-10
Application:
Building / Retaining Wall / Bridge / Slope / Tunnel / Other
Approximate Observation Distance:
Example: 50 m / 100 m / 200 m
This information makes it easier to evaluate the intended setup.
Buy Myzox Monitoring Prism in Malaysia
MTM Precision supplies Myzox TK-10S / TK-10 Monitoring Prism L-Bar Type, total station accessories and professional surveying equipment in Malaysia.
We support land surveyors, engineering surveyors, contractors, consultants and monitoring specialists requiring fixed prism targets for professional structural monitoring projects.
Contact MTM Precision
MTM Precision Sdn. Bhd.
Myzox Authorized Distributor in Malaysia
Showroom & Service Centre
No. 29-1 & 29-2, Jalan Bandar 18,
Pusat Bandar Puchong,
47160 Puchong, Selangor, Malaysia.
Website: www.mtmpre.com.my
Email: mtmpre@yahoo.com
WhatsApp: +6016-6607346
Send us your total station brand + model + required Myzox TK-10S / TK-10 quantity for product and monitoring prism enquiries in Malaysia.
18 Aug 2026
