How to Measure Motor Vibration: Step-by-Step Guide for Maintenance Engineers Malaysia

Motor vibration measurement is one of the simplest ways for maintenance engineers to monitor the condition of rotating machinery.

 

An electric motor may look and sound normal while mechanical problems are beginning to develop. Changes in vibration can provide an early indication of imbalance, misalignment, bearing deterioration, mechanical looseness and other machine problems.

 

For factories, facility management teams and maintenance contractors in Malaysia, a portable vibration meter can be used for routine motor inspections without stopping production for complicated testing.

 

What Do You Need to Measure Motor Vibration?

 

The basic instrument is a vibration meter.

 

Depending on the model, a vibration meter may measure:

 

Vibration velocity

 

Vibration acceleration

 

Vibration displacement

 

Some instruments offer multiple parameters, while simpler models may focus on particular vibration measurements.

 

MTM Precision supplies vibration meter options from brands including Showa Sokki, Landtek, Wintact and Benetech for different industrial maintenance requirements.

 

Step 1: Identify the Motor

 

Before taking measurements, record basic information about the machine.

 

Useful information includes:

 

Motor identification

 

Machine or production line

 

Motor power

 

Motor speed or RPM

 

Driven equipment

 

Operating load

 

Measurement date

 

For example:

 

Motor: Cooling Water Pump Motor No. 2

Speed: 1,450 RPM

Application: Centrifugal Pump

Location: Pump Room

 

Good records make future vibration measurements much more useful.

 

Step 2: Allow the Motor to Operate Normally

 

Whenever possible, measure vibration under normal operating conditions.

 

A motor operating without load may produce a different vibration reading from the same motor driving equipment at full operating load.

 

For condition monitoring, consistency is important.

 

Try to compare measurements taken under similar:

 

Speed → Load → Operating Condition → Measurement Location

 

This makes vibration trends easier to interpret.

 

Step 3: Choose the Correct Measurement Points

 

Vibration is commonly measured near the motor bearings.

 

For a typical motor, technicians may establish measurement points at the:

 

Drive End (DE)

 

and

 

Non-Drive End (NDE)

 

Measurements may then be taken in different directions.

 

Horizontal

 

Measures vibration in the horizontal direction.

 

Vertical

 

Measures vibration in the vertical direction.

 

Axial

 

Measures vibration along the shaft direction.

 

Using several directions can provide more information than taking a single measurement.

 

Step 4: Keep the Measurement Position Consistent

 

Repeatability is extremely important.

 

If today's reading is taken from one location and next month's measurement is taken from a different position, comparing the readings may be misleading.

 

Maintenance teams can mark permanent measurement points on critical machinery.

 

For example:

 

M1-DE-H = Motor 1, Drive End, Horizontal

 

M1-DE-V = Motor 1, Drive End, Vertical

 

M1-NDE-H = Motor 1, Non-Drive End, Horizontal

 

This creates a simple and repeatable inspection route.

 

Step 5: Measure Vibration Velocity

 

One of the most commonly encountered vibration parameters for rotating machinery is vibration velocity.

 

It is often displayed in:

 

mm/s

 

Velocity measurements are widely used for evaluating overall machinery vibration and monitoring changes over time.

 

For example:

 

January: 1.7 mm/s

 

February: 1.8 mm/s

 

March: 2.0 mm/s

 

April: 2.9 mm/s

 

May: 4.1 mm/s

 

The important information is not simply the final number.

 

The trend has changed.

 

This should encourage the maintenance team to investigate the machine.

 

Step 6: Check Acceleration When Required

 

Vibration acceleration is commonly expressed in:

 

m/s² or g

 

Acceleration responds strongly to higher-frequency vibration and can provide useful information when checking certain mechanical and bearing-related conditions.

 

Whether acceleration measurement is required depends on the machine and maintenance objective.

 

This is one reason maintenance engineers should check the measurement capabilities of a vibration meter before purchasing.

 

Step 7: Measure Displacement When Applicable

 

Vibration displacement may be expressed in units such as:

 

µm

 

Displacement describes the physical movement associated with vibration and can be useful for certain machinery and lower-frequency vibration conditions.

 

Not every maintenance application requires all three parameters.

 

The correct instrument depends on what your maintenance team needs to monitor.

 

Step 8: Record Every Measurement

 

A vibration meter becomes significantly more useful when readings are recorded.

 

A simple vibration inspection record might contain:

 

Date | Machine | Point | Direction | Velocity | Acceleration | RPM | Remarks

 

For example:

 

20 Aug | Pump Motor 2 | DE | Horizontal | 2.4 mm/s | — | 1450 RPM | Normal

 

Repeat the measurement periodically.

 

The resulting historical data can reveal changes that may not be obvious during a single inspection.

 

Step 9: Compare the Vibration Trend

 

One isolated vibration reading provides limited information.

 

A series of readings is much more powerful.

 

Suppose a motor has operated around 2 mm/s for many months and suddenly increases substantially.

 

That change deserves attention.

 

Possible causes may include:

 

Bearing deterioration

 

Rotor imbalance

 

Coupling misalignment

 

Loose mounting

 

Foundation problems

 

Fan damage

 

Problems in the driven machine

 

Vibration measurement identifies that the machine condition has changed.

 

Further inspection helps determine why.

 

Where Should You Place a Vibration Meter Sensor on a Motor?

 

For general machine condition monitoring, measurements are normally taken on rigid parts of the machine structure near the bearings.

 

Avoid inconsistent measurement positions or surfaces that may produce poor repeatability.

 

When using an external vibration sensor or probe, follow the instrument manufacturer's recommended measurement method.

 

The goal is to create a measurement that can be repeated reliably during future inspections.

 

Should You Measure the Motor or the Driven Equipment?

 

Ideally, check both.

 

If a motor drives a pump, for example, a maintenance route could include:

 

Motor NDE → Motor DE → Pump DE → Pump NDE

 

This helps technicians determine whether vibration is concentrated around the motor, coupling or pump.

 

The same principle applies to:

 

Motor + Fan

 

Motor + Compressor

 

Motor + Gearbox

 

Motor + Blower

 

Measuring the complete machine train gives a better picture than measuring the motor alone.

 

What Causes High Motor Vibration?

 

Common causes include:

 

Imbalance

 

Uneven rotating mass can increase vibration.

 

Misalignment

 

Incorrect shaft or coupling alignment can produce excessive vibration and increase bearing and coupling stress.

 

Bearing Problems

 

Bearing wear, lubrication problems and contamination may cause vibration to increase.

 

Mechanical Looseness

 

Loose mounting bolts, bearing housings or foundations can amplify vibration.

 

Soft Foot

 

Incorrect motor mounting can distort the machine and contribute to vibration.

 

Driven Equipment Problems

 

A pump, fan, compressor or gearbox can generate vibration that is transmitted to the motor.

 

What Is a Normal Motor Vibration Reading?

 

There is no universal mm/s value that should be applied blindly to every electric motor.

 

Acceptability depends on factors including:

 

Machine type

 

Machine size

 

Speed

 

Foundation

 

Mounting

 

Measurement position

 

Operating condition

 

Manufacturer recommendations

 

Applicable machinery standards

 

For condition monitoring, establishing the motor's normal baseline and watching for changes is extremely valuable.

 

How Often Should Motor Vibration Be Checked?

 

The inspection interval depends on machine criticality and operating conditions.

 

A non-critical motor may require less frequent inspection than a motor whose failure would stop an entire production line.

 

Maintenance teams can classify machinery according to importance:

 

Critical → Important → General

 

Critical equipment can then receive more frequent vibration checks.

 

This allows maintenance resources to focus on machinery where unexpected failure would have the greatest impact.

 

Portable Vibration Meter for Factory Maintenance

 

Portable vibration meters are useful because technicians can carry one instrument through a factory and check multiple machines.

 

Typical applications include:

 

Electric motors

 

Pumps

 

Bearings

 

Fans

 

Blowers

 

Compressors

 

Gearboxes

 

Generators

 

Cooling towers

 

HVAC equipment

 

Production machinery

 

This makes vibration measurement suitable for both preventive maintenance and condition-based maintenance programmes.

 

Vibration Meter Options in Malaysia

 

MTM Precision supplies several vibration measurement options.

 

Showa Sokki SH-1332B

 

Suitable for professional industrial vibration measurement and maintenance applications.

 

Landtek VM6310 / VM6360 / VM6380

 

Landtek offers portable vibration meters suitable for different machinery inspection and vibration measurement requirements.

 

Wintact Vibration Meter

 

Suitable for technicians looking for portable vibration measurement for general motor, pump, bearing and machinery checks.

 

Benetech Vibration Meter

 

Provides additional options for general industrial vibration testing and maintenance work.

 

The appropriate model depends on required parameters, measurement range and application.

 

From Motor Vibration Measurement to Predictive Maintenance

 

The biggest advantage of vibration measurement is not simply obtaining a number.

 

It is building a history of machine condition.

 

A factory can start with a simple routine:

 

Identify Critical Machines → Establish Measurement Points → Take Baseline Readings → Repeat Measurements → Track Trends → Investigate Changes

 

Over time, this turns a handheld vibration meter into a practical component of a predictive maintenance strategy.

 

Instead of waiting for a motor to fail, maintenance engineers can look for changes while the machine is still operating.

 

Looking for a Motor Vibration Meter in Malaysia?

 

MTM Precision Sdn Bhd supplies vibration meters and industrial testing instruments for maintenance engineers, factories, facility management teams, HVAC contractors and engineering companies throughout Malaysia.

 

Contact us if you need help choosing a vibration meter for:

 

Motor → Bearing → Pump → Fan → Compressor → Gearbox → Generator → HVAC → Factory Machinery

 

MTM Precision Sdn Bhd

 

Website: www.mtmpre.com.my

WhatsApp: +6016-660 7346

Email: mtmpre@yahoo.com

 

Showroom & Service Centre

No. 29-1 & 29-2, Jalan Bandar 18,

Pusat Bandar Puchong,

47160 Puchong, Selangor, Malaysia.

 

Talk to MTM Precision about selecting a suitable vibration meter for your machine maintenance and condition monitoring requirements in Malaysia.


 

20 Aug 2026