Acceptable Vibration Level for Electric Motors: mm/s Guide Malaysia

What is an acceptable vibration level for an electric motor?

 

This is one of the most common questions asked by maintenance engineers when using a vibration meter.

 

A technician may measure 1.5 mm/s, 2.8 mm/s, 4.5 mm/s or higher, but the number alone does not automatically tell you whether the motor is healthy or faulty.

 

Motor vibration should be evaluated according to the machine type, rotational speed, mounting condition, measurement location, operating condition, manufacturer recommendations, applicable standards and historical vibration trend.

 

For factories and maintenance teams in Malaysia, understanding what a vibration reading means is essential before making maintenance decisions.

 

What Does mm/s Mean on a Vibration Meter?

 

mm/s means millimetres per second.

 

It is commonly used as a unit of vibration velocity.

 

Vibration velocity is widely used for evaluating the overall vibration condition of rotating machinery such as:

 

Electric motors

 

Pumps

 

Fans

 

Blowers

 

Compressors

 

Gearboxes

 

Generators

 

HVAC equipment

 

Many portable vibration meters display vibration velocity directly in mm/s.

 

Why Is Vibration Velocity Used for Motors?

 

A rotating machine produces vibration during normal operation.

 

The objective is therefore not necessarily to achieve zero vibration.

 

Instead, maintenance engineers want to determine whether vibration is:

 

Normal → Changing → Elevated → Potentially Serious

 

Velocity provides a practical measurement for evaluating overall machinery vibration.

 

When readings are recorded repeatedly, vibration velocity can also reveal deterioration over time.

 

Is 2 mm/s Motor Vibration Acceptable?

 

Possibly — but the number cannot be evaluated correctly without context.

 

A reading of 2 mm/s may be acceptable for one machine but should not automatically be used as a universal limit for every motor.

 

Consider:

 

Where was the measurement taken?

 

What is the motor RPM?

 

Is the motor rigidly or flexibly mounted?

 

What equipment is connected to the motor?

 

What was the previous vibration level?

 

Is the machine operating at its normal load?

 

What limits apply to that specific machine?

 

These questions are important when interpreting vibration measurements.

 

Is 4 mm/s Too High for a Motor?

 

Again, it depends on the machine and applicable evaluation criteria.

 

A single reading should not be interpreted without considering the equipment.

 

However, a significant increase from the machine's normal baseline deserves investigation.

 

For example:

 

Normal historical vibration:

 

1.8–2.1 mm/s

 

Current measurement:

 

4.0 mm/s

 

The important information is not only that the reading is 4.0 mm/s.

 

The machine's vibration has approximately doubled compared with its normal condition.

 

That change should trigger further inspection.

 

What Is RMS Vibration?

 

Many machinery vibration measurements are expressed as RMS — Root Mean Square.

 

RMS provides a useful representation of vibration magnitude and is commonly encountered when evaluating overall vibration velocity.

 

When comparing readings, technicians should confirm that they are comparing the same measurement type and units.

 

For example, do not casually compare:

 

Velocity RMS in mm/s

 

with

 

Acceleration in m/s²

 

They represent different vibration parameters.

 

Velocity vs Acceleration vs Displacement

 

Portable vibration meters may measure one or more of three common parameters.

 

Vibration Velocity

 

Common unit:

 

mm/s

 

Often used for overall machinery condition assessment.

 

Vibration Acceleration

 

Common units:

 

m/s² or g

 

Acceleration is sensitive to higher-frequency vibration and can be useful for certain bearing and mechanical conditions.

 

Vibration Displacement

 

Common unit:

 

µm

 

Displacement describes the movement associated with vibration and may be useful for certain lower-frequency machinery conditions.

 

The most appropriate parameter depends on the machine and the purpose of the inspection.

 

Why You Should Not Use One mm/s Limit for Every Motor

 

Imagine a factory containing:

 

0.75 kW fan motor

 

7.5 kW pump motor

 

30 kW compressor motor

 

75 kW production machine motor

 

160 kW process motor

 

These machines differ significantly in size, construction, operating speed, foundation and application.

 

Applying one universal alarm level to every motor can therefore produce misleading maintenance decisions.

 

Appropriate machinery standards, equipment manufacturer guidance and machine-specific operating history should be considered.

 

ISO Standards and Motor Vibration

 

Industrial vibration assessment may refer to applicable machinery vibration standards, including standards within the ISO 20816 series, depending on the machine and application.

 

However, technicians should not simply take a generic vibration chart from the internet and apply it to every machine.

 

The relevant standard, machine classification, operating condition and measurement method need to be considered.

 

When in doubt, refer to the equipment manufacturer's recommendations and the applicable current standard for the machinery being evaluated.

 

Why Baseline Vibration Is Important

 

One of the most useful measurements is the machine's own normal vibration.

 

Suppose a newly serviced motor operates normally at:

 

DE Horizontal: 1.6 mm/s

 

DE Vertical: 1.4 mm/s

 

NDE Horizontal: 1.5 mm/s

 

Record these readings.

 

Future measurements can then be compared against this baseline.

 

Six months later:

 

DE Horizontal: 2.7 mm/s

 

Twelve months later:

 

DE Horizontal: 3.8 mm/s

 

Even without waiting for an alarm limit to be exceeded, the increasing trend provides valuable maintenance information.

 

Where Should Motor Vibration Be Measured?

 

Common measurement locations are close to the motor bearings.

 

Typical points include:

 

Drive End (DE)

Non-Drive End (NDE)

 

Measurements may be taken in:

 

Horizontal

 

Vertical

 

Axial

 

For condition monitoring, the most important rule is consistency.

 

Measure the same point, in the same direction and under similar operating conditions whenever possible.

 

Why Motor RPM Matters

 

Rotational speed affects machinery vibration behaviour.

 

A motor operating at approximately 1,450 RPM may behave differently from a motor operating at approximately 2,900 RPM.

 

Variable-speed equipment introduces another challenge.

 

If one measurement is taken at low speed and another at full speed, directly comparing the numbers may not provide a meaningful trend.

 

Record RPM or operating speed whenever practical.

 

Why Load Matters

 

Motor vibration can change according to operating load.

 

For example, a pump operating at one process condition may produce different vibration from the same pump operating at another condition.

 

A useful vibration record should therefore include operating information where possible.

 

Example:

 

Pump Motor 03

 

Velocity: 2.4 mm/s RMS

 

Speed: 1,480 RPM

 

Load: Normal production

 

Point: Motor DE Horizontal

 

This is much more useful than recording only:

 

2.4 mm/s

 

What Causes Motor Vibration to Increase?

 

If motor vibration increases compared with previous measurements, investigate possible causes such as:

 

Rotor Imbalance

 

Uneven rotating mass can produce increased vibration.

 

Misalignment

 

Incorrect motor-to-machine shaft alignment can increase vibration and mechanical stress.

 

Bearing Deterioration

 

Bearing wear, lubrication problems and contamination can alter vibration.

 

Mechanical Looseness

 

Loose mounting bolts, bearing housings or foundations can amplify vibration.

 

Soft Foot

 

Uneven motor mounting can contribute to distortion, alignment problems and vibration.

 

Driven Equipment Problems

 

The vibration may originate from a connected pump, fan, compressor or gearbox rather than the motor itself.

 

Example: Motor Vibration Trending

 

Consider a factory that records monthly vibration readings:

 

January — 1.7 mm/s

 

February — 1.8 mm/s

 

March — 1.8 mm/s

 

April — 2.0 mm/s

 

May — 2.4 mm/s

 

June — 3.1 mm/s

 

July — 4.0 mm/s

 

Instead of waiting for complete motor failure, the maintenance engineer can investigate the increasing trend.

 

Possible checks may include:

 

Bearing → Alignment → Coupling → Mounting → Driven Machine

 

This is the practical value of vibration condition monitoring.

 

Should I Stop a Motor Because the Vibration Is High?

 

A portable vibration meter alone should not be used to make an automatic shutdown decision without considering the machine, operating procedures and applicable limits.

 

Maintenance personnel should evaluate:

 

Severity of the vibration

 

Rate of change

 

Noise

 

Temperature

 

Operating condition

 

Machine criticality

 

Manufacturer recommendations

 

Applicable standards

 

Site safety procedures

 

A sudden large change may require more urgent investigation than a small stable variation.

 

Portable Vibration Meter for Motor Maintenance

 

A handheld vibration meter allows technicians to move through the facility and check many machines.

 

A typical inspection route could be:

 

Motor 01 → Pump 01 → Motor 02 → Compressor → Cooling Tower Fan → Exhaust Fan → Generator

 

Readings can then be entered into a maintenance record.

 

This creates a simple condition monitoring programme without requiring permanent sensors on every machine.

 

Vibration Meter Options from MTM Precision

 

MTM Precision supplies vibration meters for industrial maintenance and machine condition monitoring applications in Malaysia.

 

Showa Sokki SH-1332B

 

Suitable for professional industrial vibration measurement and machinery maintenance applications.

 

Landtek VM6310 / VM6360 / VM6380

 

Portable vibration meter options for different machinery vibration measurement requirements.

 

Wintact Vibration Meters

 

Portable options for routine motor, bearing, pump and machinery vibration inspection.

 

Benetech Vibration Meters

 

Additional options for general industrial vibration measurement and maintenance applications.

 

Instrument selection should consider the required vibration parameters, measurement range and intended machine application.

 

Don't Ask Only “Is This mm/s Too High?”

 

A better condition-monitoring question is:

 

“How does this reading compare with the machine's normal vibration?”

 

Then consider:

 

Baseline + Trend + Machine Type + Operating Condition + Applicable Limits

 

This provides a much stronger basis for maintenance decisions than relying on a single vibration number.

 

Looking for a Vibration Meter in Malaysia?

 

MTM Precision Sdn Bhd supplies vibration measurement and industrial testing instruments for factories, maintenance departments, facility management, HVAC contractors and engineering companies in Malaysia.

 

Applications include:

 

Electric Motors → Bearings → Pumps → Fans → Blowers → Compressors → Gearboxes → Generators → HVAC → Factory Machinery

 

Contact MTM Precision if you need assistance selecting a vibration meter for routine machine inspection, troubleshooting or condition monitoring.

 

MTM Precision Sdn Bhd

 

Website: www.mtmpre.com.my

WhatsApp: +6016-660 7346

Email: mtmpre@yahoo.com

 

Showroom & Service Centre

No. 29-1 & 29-2, Jalan Bandar 18,

Pusat Bandar Puchong,

47160 Puchong, Selangor, Malaysia.


 

20 Aug 2026