Compressor Vibration Troubleshooting: Causes, Measurement & Condition Monitoring Malaysia

Compressor vibration is an important condition indicator for factories, workshops, HVAC systems and industrial facilities.

 

A compressor can continue operating even when vibration has started increasing. If the underlying problem is not identified, abnormal vibration may contribute to bearing damage, coupling wear, looseness, seal problems, piping issues and unexpected compressor shutdown.

 

For maintenance engineers in Malaysia, routine vibration measurement provides a practical way to monitor compressor condition and identify changes before they develop into major failures.

 

Why Is My Compressor Vibrating?

 

Some vibration is normal whenever rotating machinery is operating.

 

The maintenance concern begins when vibration becomes excessive, changes suddenly or gradually increases compared with the machine's normal condition.

 

Possible causes of compressor vibration include:

 

Bearing deterioration

 

Rotor imbalance

 

Motor-compressor misalignment

 

Coupling problems

 

Mechanical looseness

 

Poor foundation

 

Belt or pulley problems

 

Shaft problems

 

Piping vibration

 

Resonance

 

Problems originating from the drive motor

 

The exact causes depend on the compressor design and installation.

 

A high vibration reading therefore indicates that further investigation may be required rather than automatically identifying one specific fault.

 

Bearing Problems and Compressor Vibration

 

Bearings are important components in rotating compressor systems.

 

Bearing condition may deteriorate because of:

 

Insufficient lubrication

 

Excessive lubrication

 

Contamination

 

Incorrect installation

 

Misalignment

 

Excessive loading

 

Wear

 

Long operating hours

 

As bearing condition changes, vibration may also change.

 

Routine vibration trending allows maintenance personnel to compare current measurements with previous readings.

 

Motor-Compressor Misalignment

 

For compressors driven by an external electric motor, alignment between the motor and compressor is important.

 

Misalignment can place additional stress on:

 

Bearings → Coupling → Shafts → Seals

 

Possible causes include:

 

Incorrect installation

 

Foundation movement

 

Maintenance work

 

Coupling replacement

 

Motor replacement

 

Thermal movement

 

If vibration increases following maintenance work, alignment should be included in the troubleshooting process.

 

Rotor Imbalance

 

A rotating component with uneven mass distribution can generate vibration.

 

Depending on compressor construction, imbalance may develop because of:

 

Wear

 

Contamination

 

Component damage

 

Incorrect assembly

 

Mechanical deterioration

 

The vibration behaviour may change with rotational speed.

 

More detailed vibration analysis may be required to confirm the exact source.

 

Mechanical Looseness

 

Loose mounting can create significant vibration.

 

Inspect:

 

Compressor mounting bolts

 

Motor mounting bolts

 

Base frame

 

Foundation

 

Bearing housings

 

Guards

 

Couplings

 

Supporting structures

 

Sometimes the compressor itself is healthy, while looseness in the installation is amplifying vibration.

 

Belt-Driven Compressor Vibration

 

Some compressors use belt-driven systems.

 

Potential vibration sources include:

 

Incorrect belt tension

 

Worn belts

 

Damaged belts

 

Pulley misalignment

 

Worn pulleys

 

Motor mounting problems

 

The complete drive system should therefore be inspected:

 

Motor → Pulley → Belt → Compressor Pulley → Shaft → Bearings

 

Checking only the compressor may overlook the actual source.

 

Piping Vibration

 

Compressor piping can also vibrate.

 

Possible contributing factors include:

 

Poor support

 

Mechanical resonance

 

Pulsation

 

Installation stress

 

Loose pipe supports

 

Vibration transmitted through piping may affect the compressor or nearby equipment.

 

If abnormal vibration appears around connected piping, the supporting structure and operating conditions should also be investigated.

 

How Do You Measure Compressor Vibration?

 

A portable vibration meter can be used to take measurements from appropriate locations while the equipment operates under suitable normal conditions.

 

Depending on the instrument, measurements may include:

 

Vibration Velocity

 

Usually expressed in:

 

mm/s

 

Velocity is commonly used for overall rotating machinery vibration assessment and condition trending.

 

Vibration Acceleration

 

Commonly expressed in:

 

m/s² or g

 

Acceleration can provide useful information about higher-frequency vibration and certain bearing-related conditions.

 

Vibration Displacement

 

Often expressed in:

 

µm

 

Displacement may be useful for particular machinery and lower-frequency vibration applications.

 

Not every application requires all three parameters.

 

The appropriate vibration meter should be selected according to the maintenance requirement.

 

Where Should Compressor Vibration Be Measured?

 

Measurement locations depend on the compressor design.

 

For a motor-driven compressor, a practical route may include appropriate points around:

 

Motor NDE → Motor DE → Coupling Area → Compressor Bearing Locations

 

Measurements can be taken in directions such as:

 

Horizontal

 

Vertical

 

Axial

 

Always follow the equipment and vibration instrument manufacturer's recommendations.

 

For trending purposes, use the same measurement points during each inspection whenever practical.

 

Why Measurement Location Matters

 

Suppose a technician takes a measurement from one part of the compressor this month and another location next month.

 

Even if both readings are technically correct, comparing them may provide little useful trend information.

 

Instead, establish fixed locations.

 

For example:

 

COMP-01-M-DE-H

 

Compressor 01 → Motor → Drive End → Horizontal

 

COMP-01-C-DE-H

 

Compressor 01 → Compressor → Drive End → Horizontal

 

This improves repeatability.

 

Compressor Vibration Trending

 

Consider a compressor with the following measurements at the same location:

 

January — 2.0 mm/s

 

February — 2.1 mm/s

 

March — 2.0 mm/s

 

April — 2.4 mm/s

 

May — 3.0 mm/s

 

June — 3.9 mm/s

 

The increasing trend provides maintenance personnel with a reason to investigate.

 

Possible checks could include:

 

Bearing → Alignment → Coupling → Mounting → Drive System

 

This can be much more useful than waiting until the compressor becomes extremely noisy or fails.

 

What Is an Acceptable Compressor Vibration Level?

 

There is no single mm/s value suitable for every compressor.

 

Evaluation depends on factors such as:

 

Compressor type

 

Machine size

 

Rotational speed

 

Power

 

Mounting

 

Foundation

 

Measurement position

 

Operating load

 

Manufacturer recommendations

 

Applicable machinery standards

 

A vibration limit used for one compressor should not automatically be applied to every other machine.

 

Machine-specific baseline measurements and trends provide additional information.

 

Why Operating Condition Matters

 

Compressor vibration may vary with operating condition.

 

When recording measurements, consider information such as:

 

Speed

 

Load

 

Pressure

 

Operating mode

 

Temperature

 

Production condition

 

For reliable trending, measurements should ideally be compared under reasonably similar conditions.

 

A reading without operating context may be difficult to interpret later.

 

Air Compressor Vibration Monitoring

 

Compressed air is essential to many manufacturing plants.

 

It may power:

 

Pneumatic tools

 

Production machinery

 

Actuators

 

Packaging systems

 

Automation equipment

 

Instrument air systems

 

An unexpected air compressor failure can therefore affect multiple production areas.

 

This makes critical air compressors good candidates for routine condition monitoring.

 

HVAC Compressor Vibration

 

Compressors are also important components in HVAC and refrigeration systems.

 

Facility maintenance teams may use vibration measurements together with other inspection information when evaluating mechanical condition.

 

Depending on system design, vibration may be checked around:

 

Motor → Compressor → Mounting → Connected Structure

 

Complex refrigeration or compressor faults should be diagnosed by appropriately qualified personnel.

 

Should You Measure Temperature Too?

 

Vibration provides one view of machine condition.

 

Maintenance engineers often obtain a better picture by combining several indicators:

 

Vibration + Temperature + Noise + Lubrication + Operating Performance

 

For example, increasing bearing vibration together with abnormal bearing temperature may justify more urgent investigation than either observation alone.

 

Condition monitoring is strongest when multiple relevant indicators are considered together.

 

Vibration Meter vs Vibration Analyzer for Compressors

 

A portable vibration meter is useful for:

 

Routine inspections

 

Comparing vibration levels

 

Detecting changes

 

Maintenance routes

 

Basic condition monitoring

 

A vibration analyzer provides deeper diagnostic capabilities and may include frequency-domain analysis.

 

For routine factory maintenance, a vibration meter can serve as a first-line screening instrument.

 

Machines showing abnormal behaviour can then receive more detailed investigation.

 

Portable Vibration Meter Options from MTM Precision

 

MTM Precision supplies vibration measurement instruments for compressor and rotating machinery maintenance applications in Malaysia.

 

Showa Sokki SH-1332B

 

Suitable for professional industrial vibration measurement and maintenance applications.

 

Landtek VM6310 / VM6360 / VM6380

 

Portable vibration meter options for different industrial machinery vibration measurement requirements.

 

Wintact Vibration Meters

 

Suitable for general compressor, motor, pump, bearing and machinery vibration checks.

 

Benetech Vibration Meters

 

Additional portable vibration measurement options for general industrial maintenance applications.

 

Instrument selection should consider the machine, required vibration parameters and intended maintenance programme.

 

Build a Compressor Condition Monitoring Routine

 

A practical programme can begin with:

 

1. Identify critical compressors

 

Determine which machines would have the greatest operational impact if they failed.

 

2. Establish measurement points

 

Select repeatable locations around bearings and other appropriate machine areas.

 

3. Take baseline readings

 

Record measurements while the compressor is operating normally.

 

4. Repeat measurements

 

Use a suitable inspection interval based on machine criticality.

 

5. Track trends

 

Compare new measurements with historical data.

 

6. Investigate significant changes

 

Check bearings, alignment, coupling, mounting and other possible sources.

 

This approach moves compressor maintenance from purely reactive repair toward condition-based maintenance.

 

Looking for a Compressor Vibration Meter in Malaysia?

 

MTM Precision Sdn Bhd supplies vibration meters and industrial testing instruments for factory maintenance, engineering, HVAC, facility management and machine condition monitoring applications in Malaysia.

 

Vibration meter applications include:

 

Compressors → Motors → Bearings → Pumps → Fans → Blowers → Gearboxes → Generators → Factory Machinery

 

Contact MTM Precision for assistance selecting a vibration meter according to your compressor and machinery maintenance requirements.

 

MTM Precision Sdn Bhd

 

Website: www.mtmpre.com.my

WhatsApp: +6016-660 7346

Email: mtmpre@yahoo.com

 

Showroom & Service Centre

No. 29-1 & 29-2, Jalan Bandar 18,

Pusat Bandar Puchong,

47160 Puchong, Selangor, Malaysia.


 

20 Aug 2026