Motor Misalignment and Vibration: How to Detect Shaft & Coupling Problems Malaysia

Motor misalignment is a common mechanical problem in rotating machinery.

 

When an electric motor is connected to a pump, compressor, gearbox, fan or other driven equipment, the shafts need to be correctly aligned. Poor alignment can increase vibration and place additional mechanical stress on bearings, couplings, seals and shafts.

 

For maintenance engineers in Malaysia, vibration measurement can provide useful information when checking motor-driven machinery for changing mechanical condition.

 

What Is Motor Misalignment?

 

Misalignment occurs when the rotational centre lines of two connected shafts are not positioned correctly relative to each other.

 

A typical machine train may look like:

 

Electric Motor → Coupling → Pump

 

or:

 

Electric Motor → Coupling → Gearbox → Driven Machine

 

If the shafts are not correctly aligned, additional forces can be generated while the machine operates.

 

These forces may contribute to increased vibration and component wear.

 

What Causes Motor Misalignment?

 

Possible causes include:

 

Incorrect initial installation

 

Poor alignment procedure

 

Foundation movement

 

Loose mounting

 

Soft foot

 

Thermal movement

 

Motor replacement

 

Pump replacement

 

Coupling replacement

 

Pipe strain

 

Machine movement over time

 

A machine that was aligned correctly during commissioning may not remain aligned forever.

 

This is why condition monitoring and periodic mechanical inspection are important.

 

What Are the Symptoms of Misalignment?

 

Possible signs include:

 

Increased vibration

 

Coupling wear

 

Bearing problems

 

Seal problems

 

Elevated temperature

 

Abnormal noise

 

Repeated component failures

 

However, these symptoms are not unique to misalignment.

 

Imbalance, looseness and bearing deterioration can produce similar symptoms.

 

Further investigation is required before confirming the root cause.

 

Angular vs Parallel Misalignment

 

Two commonly discussed alignment conditions are angular and parallel misalignment.

 

Angular Misalignment

 

The shaft centre lines are positioned at an angle relative to each other.

 

Parallel Misalignment

 

The shaft centre lines are offset while remaining approximately parallel.

 

A machine may also have a combination of both conditions.

 

Correct alignment procedures and suitable alignment equipment should be used when installing or correcting coupled machinery.

 

How Does Misalignment Cause Vibration?

 

A coupling is designed to transmit rotational power between shafts.

 

Although some couplings can tolerate limited misalignment, excessive misalignment introduces additional mechanical forces into the machine.

 

These forces can affect:

 

Coupling → Shaft → Bearing → Seal

 

The resulting vibration may be detected at motor and driven-machine bearing locations.

 

How Can a Vibration Meter Help?

 

A portable vibration meter can be used to measure vibration at repeatable points across the machine train.

 

Depending on the instrument, parameters may include:

 

Vibration Velocity

 

Commonly expressed in:

 

mm/s

 

Useful for overall machinery vibration assessment and trending.

 

Vibration Acceleration

 

Commonly expressed in:

 

m/s² or g

 

Useful for higher-frequency vibration and certain mechanical conditions.

 

Vibration Displacement

 

Often expressed in:

 

µm

 

Useful for particular machinery vibration applications.

 

The meter can show whether machine vibration is elevated or changing.

 

However, overall vibration alone may not definitively prove misalignment.

 

Where Should You Measure?

 

For a motor-driven pump, a useful measurement route may include:

 

Motor NDE → Motor DE → Pump DE → Pump NDE

 

Measurements may be taken in:

 

Horizontal

 

Vertical

 

Axial

 

When investigating suspected coupling or shaft alignment problems, measurements at several locations provide more information than one isolated reading.

 

Use consistent measurement locations for trending.

 

Why Axial Vibration Can Be Important

 

When troubleshooting coupled machinery, axial vibration is one of the measurements maintenance personnel may consider.

 

However, no single direction should automatically be used to diagnose misalignment.

 

The overall machine behaviour, measurement locations, vibration characteristics and mechanical inspection should be evaluated together.

 

For complex problems, advanced vibration analysis may be required.

 

Example: Motor-Pump Vibration Problem

 

Consider a pump set that normally operates around:

 

Motor DE: 1.8 mm/s

 

Pump DE: 2.0 mm/s

 

After motor replacement, measurements become:

 

Motor DE: 3.8 mm/s

 

Pump DE: 4.0 mm/s

 

Because the vibration changed following maintenance work, the technician may investigate:

 

Shaft alignment

 

Coupling condition

 

Motor mounting

 

Soft foot

 

Pump mounting

 

The timing of the vibration change provides an important troubleshooting clue.

 

Misalignment After Motor Replacement

 

Whenever a motor is removed and reinstalled, alignment should receive attention.

 

Even when the replacement motor has the same frame size, small differences in:

 

Position

 

Mounting

 

Shims

 

Coupling arrangement

 

can affect alignment.

 

Taking vibration measurements before and after major maintenance can provide useful verification data.

 

Misalignment After Pump Maintenance

 

Pump maintenance may involve removing:

 

Pump

 

Motor

 

Coupling

 

Bearings

 

Base components

 

After reassembly, vibration measurements can be compared with historical baseline readings.

 

If vibration is significantly higher than before maintenance, investigate the installation before returning the machine to long-term operation.

 

Soft Foot and Misalignment

 

Soft foot occurs when the machine feet do not sit evenly on the mounting surface.

 

Tightening mounting bolts under these conditions can distort the machine frame or alter shaft alignment.

 

Possible consequences include:

 

Soft Foot → Distortion → Alignment Problems → Increased Vibration

 

Soft foot should therefore be considered when alignment problems repeatedly return.

 

Pipe Strain and Pump Alignment

 

Connected piping can place mechanical forces on a pump.

 

Poor piping support or incorrect installation can influence pump position and alignment.

 

If a pump repeatedly loses alignment, check more than the coupling.

 

The complete installation may need inspection.

 

Misalignment vs Imbalance

 

These two faults are commonly confused.

 

Imbalance

 

Related to uneven rotating mass distribution.

 

Misalignment

 

Related to incorrect shaft positioning between connected machines.

 

Both can cause increased vibration.

 

A portable vibration meter can detect changing vibration, while more advanced analysis and mechanical inspection may be needed to distinguish the exact cause.

 

Misalignment vs Bearing Failure

 

High vibration around a bearing does not automatically mean the bearing itself is defective.

 

A misaligned shaft can place additional loads on bearings and cause them to operate under poor conditions.

 

Replacing the bearing without correcting the underlying alignment problem may result in repeated failure.

 

This is why root-cause thinking is important.

 

Should You Align a Machine Based on Vibration Alone?

 

No.

 

A vibration meter is not a substitute for proper shaft alignment measurement.

 

If alignment is suspected, suitable shaft alignment methods and equipment should be used.

 

Vibration measurement provides complementary information.

 

A practical process can be:

 

High Vibration Detected

 

↓

 

Mechanical Inspection

 

↓

 

Alignment Checked

 

↓

 

Correction Performed

 

↓

 

Vibration Re-Measured

 

This allows the technician to verify whether machine condition improved after correction.

 

Measure Before and After Alignment

 

Consider:

 

Before alignment:

 

Motor DE Horizontal: 4.1 mm/s

 

After proper mechanical correction:

 

Motor DE Horizontal: 2.0 mm/s

 

The before-and-after measurements provide useful maintenance evidence.

 

Record both values in the equipment history.

 

Motor-Pump Alignment Applications

 

Alignment-related vibration monitoring is relevant for:

 

Chilled water pumps

 

Condenser water pumps

 

Process pumps

 

Booster pumps

 

Cooling water pumps

 

Chemical pumps

 

Water treatment pumps

 

These systems are common in factories, commercial buildings and industrial facilities throughout Malaysia.

 

Motor-Compressor Alignment

 

Motor-driven compressors may also develop alignment-related problems.

 

Routine vibration measurements can be taken around:

 

Motor Bearings → Coupling Area → Compressor Bearings

 

If vibration changes after coupling or motor work, alignment should be included in the investigation.

 

Motor-Gearbox Alignment

 

Industrial drive systems frequently use:

 

Motor → Coupling → Gearbox

 

and sometimes:

 

Motor → Gearbox → Driven Equipment

 

Misalignment can therefore occur on either side of the gearbox.

 

Measurements across the complete machine train can help identify where vibration is concentrated.

 

Misalignment and Predictive Maintenance

 

A condition monitoring programme can help identify alignment-related deterioration before severe component damage develops.

 

The process is:

 

Baseline → Periodic Measurement → Detect Change → Investigate → Correct → Verify

 

This approach can reduce dependence on waiting for obvious symptoms such as excessive noise or severe machine shaking.

 

Vibration Meter or Vibration Analyzer?

 

A portable vibration meter is suitable for:

 

Routine checks

 

Overall vibration measurement

 

Baseline readings

 

Trending

 

Before-and-after maintenance verification

 

A vibration analyzer may be useful when detailed frequency analysis and fault diagnosis are required.

 

For routine maintenance teams, a portable meter provides an effective first-line tool.

 

Vibration Meter Options from MTM Precision Malaysia

 

MTM Precision supplies vibration measurement equipment for motor alignment troubleshooting and industrial machine condition monitoring applications.

 

Showa Sokki SH-1332B

 

Suitable for professional industrial vibration measurement and maintenance applications.

 

Landtek VM6310 / VM6360 / VM6380

 

Portable vibration meter options for different machinery vibration measurement requirements.

 

Wintact Vibration Meters

 

Suitable for routine motor, pump, bearing and machinery vibration checks.

 

Benetech Vibration Meters

 

Additional portable options for general industrial vibration measurement and maintenance.

 

Instrument selection should be based on required parameters and application.

 

Don't Treat High Vibration as the Diagnosis

 

If a motor-pump set is vibrating excessively, do not immediately conclude:

 

“Bearing damaged.”

 

Consider the complete system:

 

Imbalance → Misalignment → Bearing Condition → Coupling → Soft Foot → Mounting → Foundation → Driven Machine

 

Vibration is an important clue.

 

Good troubleshooting combines that clue with mechanical inspection and appropriate measurement techniques.

 

Looking for a Motor Vibration Meter in Malaysia?

 

MTM Precision Sdn Bhd supplies vibration meters and industrial testing instruments for factory maintenance, engineering, HVAC, facility management and machine condition monitoring applications in Malaysia.

 

Applications include:

 

Motor → Pump → Coupling → Bearing → Fan → Compressor → Gearbox → Generator → Factory Machinery

 

Contact MTM Precision for assistance selecting a suitable vibration meter for routine machinery inspection, troubleshooting and condition monitoring.

 

MTM Precision Sdn Bhd

 

Website: www.mtmpre.com.my

WhatsApp: +6016-660 7346

Email: mtmpre@yahoo.com

 

Showroom & Service Centre

No. 29-1 & 29-2, Jalan Bandar 18,

Pusat Bandar Puchong,

47160 Puchong, Selangor, Malaysia.


 

20 Aug 2026