Factory Ventilation Problem What Should You Measure Malaysia

Factory Ventilation Problem What Should You Measure Malaysia A factory may have fans, air-conditioning and exhaust systems installed, but workers still complain: “The air feels stuffy.” “This area is very hot.” “There is almost no air movement.” “The chemical smell stays inside the production area.” “The exhaust system does not seem effective.” When this happens, simply installing another fan may not solve the real problem. The first step is to understand: What is actually happening with the ventilation? A practical investigation may involve: Air Velocity → Temperature → Humidity → CO → Particulate → VOC / Gas Where Relevant 1. Start With the Complaint “Poor ventilation” can describe several different problems. For example: “There is no air movement.” Investigate: Air Velocity → Supply / Exhaust Airflow “The room feels stuffy.” Possible investigation: CO → Temperature → Humidity → Airflow “Chemical smell accumulates during production.” Possible investigation: VOC / Relevant Gas → Airflow → Local Exhaust “The production area is too hot.” Possible investigation: Temperature → Humidity → Air Velocity → Heat Stress Different symptoms require different measurements. 2. Measure Air Velocity An anemometer can help quantify air movement. Instead of saying: “The fan seems weak.” you can measure air velocity at relevant locations. Possible measurement points include: Supply-air outlets Exhaust points Duct openings Workstations Production areas Air intakes Local extraction systems This helps turn a subjective complaint into measurable information. 3. Don't Measure Only Directly in Front of the Fan A common mistake is measuring only where airflow is obviously strongest. The objective may actually be to understand what workers experience. Consider comparing: Supply Outlet ↓ Middle of Work Area ↓ Worker Position ↓ Problem Area ↓ Exhaust Point A strong reading directly in front of a fan does not automatically mean the entire room has good air distribution. 4. Look for Dead Zones Factories can have areas with very little air movement. Possible reasons include: Machinery blocking airflow Storage racks Partition walls Poor fan positioning Production-line layout Closed doors Building modifications Measurements at multiple points can help identify areas where air circulation differs significantly. 5. CO Can Help Investigate Occupied Areas In occupied indoor spaces, CO measurement may provide useful information when investigating ventilation. Potential locations include: Offices inside factories Meeting rooms Control rooms Laboratories Staff rooms Enclosed production areas However, CO is only one parameter. It should not automatically be treated as a complete indoor air quality assessment. 6. Temperature and Humidity Matter Workers sometimes describe a workplace as poorly ventilated when the main complaint is actually thermal discomfort. Measure: Temperature and Relative Humidity Then consider: Air Velocity For heat-stress-related applications, additional measurements such as WBGT may also be relevant. 7. Chemical Areas Need a Different Approach Suppose the complaint is: “Our painting section has a strong solvent smell even though the exhaust fan is running.” This is not simply an airflow problem. The investigation may require: Chemical / Process Identification ↓ VOC or Relevant Gas Measurement ↓ Air Velocity ↓ Local Exhaust Investigation ↓ Compare Production ON / OFF The contaminant and ventilation system should be considered together. 8. Dust Extraction Is Another Ventilation Problem A grinding or powder-handling area may have an extraction system, yet dust still escapes into the factory. Possible investigation: PM2.5 / PM10 ↓ Air Velocity ↓ Extraction Point ↓ Worker Position ↓ Adjacent Area This helps determine whether particulate conditions change according to extraction performance. 9. Compare Ventilation ON and OFF Where appropriate and safe, comparing operating conditions can provide useful troubleshooting information. For example: Ventilation OFF → Baseline Measurement and Ventilation ON → Repeat Measurement Compare relevant parameters such as: Air velocity Temperature CO PM VOC where applicable The exact method should suit the workplace and safety requirements. 10. Compare Before and After Maintenance Ventilation systems can lose performance because of: Dirty filters Blocked ducts Damaged fans Belt problems Obstructions Equipment wear System modifications Measurements can be taken: Before Maintenance and After Maintenance This provides evidence of whether performance has changed. 11. Conditions May Change During Production A factory may appear comfortable before production starts. Then: Machines Start ↓ Heat Increases ↓ Processes Generate Dust / Vapour ↓ More Workers Enter ↓ Environmental Conditions Change This means a ventilation assessment performed only when production is stopped may not represent normal operating conditions. 12. Spot Measurement or Continuous Monitoring? If the problem occurs occasionally, a spot measurement may miss it. For example: 8:00 AM Normal 11:00 AM Temperature rising 2:00 PM CO increasing 4:00 PM Workers complain In such cases, data logging or continuous environmental monitoring may help reveal the pattern. 13. Example: Factory Office Feels Stuffy Every Afternoon Suppose a customer says: “Our office inside the factory feels very stuffy after lunch.” Instead of immediately recommending an air quality meter, investigate: How many people occupy the room? Is fresh air supplied? Is the air-conditioning recirculating air? Does the problem happen at the same time every day? Possible measurement pathway: CO ↓ Temperature & Humidity ↓ Air Velocity ↓ Monitor Throughout the Day ↓ Compare Occupancy and Ventilation Conditions This creates a useful troubleshooting process. 14. Example: Exhaust Fan Runs but Chemical Smell Remains Another customer says: “Our exhaust fan is working, but the chemical smell is still strong.” Possible measurement pathway: Identify Chemical / Process ↓ Measure Relevant VOC / Gas Where Appropriate ↓ Measure Air Velocity ↓ Compare Source and Worker Position ↓ Check Exhaust Performance ↓ Corrective Action ↓ Measure Again This is much more useful than simply replacing the fan without measurement. What Instruments Might Be Needed? Depending on the problem, a factory ventilation investigation may involve: Anemometer For measuring air velocity. Temperature & Humidity Meter For environmental comfort and supporting measurements. CO Meter For appropriate occupied-space ventilation investigations. Air Quality / Particulate Meter For PM2.5 and PM10 screening applications. VOC / Gas Detector Where specific processes or contaminants need investigation. WBGT Meter Where occupational heat stress is the concern. Data Logger For monitoring environmental changes over time. Not every ventilation problem requires every instrument. The correct combination depends on the complaint. Ventilation Is Not Just “Airflow” This is the important point. A factory can have measurable airflow and still have another environmental problem. The full investigation may need to consider: Air Movement Fresh Air Temperature Humidity Particles Chemical Vapours Gas Worker Location Production Conditions That is why factory ventilation should be treated as a system rather than a single meter reading. From Ventilation Complaint to Measurement Solution Instead of: Poor Ventilation → Buy Anemometer MTM's approach is: Understand the Complaint ↓ Identify the Work Area ↓ Measure Air Velocity ↓ Check Environmental Parameters ↓ Check Relevant Contaminants ↓ Compare Locations ↓ Compare Operating Conditions ↓ Take Corrective Action ↓ Measure Again This turns a ventilation complaint into a structured measurement process. One Problem Can Require Several Measurement Categories A poorly ventilated production area could involve: Airflow → Temperature & Humidity → CO → PM2.5 / PM10 → VOC / Gas → WBGT The customer does not need to know which instrument category to search. They only need to tell MTM: “Our factory ventilation is not good.” From there, we can help determine what should be measured. Factory Environmental & Safety Measurement Solutions Malaysia MTM Precision supports factories, EHS departments, facility managers, mainenance teams, engineers and contractors with testing and measurement solutions covering: Airflow Ventilation Indoor Air Quality CO PM2.5 / PM10 VOC Gas Detection Temperature & Humidity Heat Stress Noise Vibration Industrial Maintenance The principle is simple: You tell us the problem. We help identify what needs to be measured. Need Help Investigating Factory Ventilation? Tell MTM: What is the complaint? Where does it happen? Is the problem heat, stuffiness, dust, chemical vapour or gas? When does it occur? What ventilation system is currently installed? We can help identify suitable measurement options for your application. MTM Precision Sdn Bhd Showroom & Service Centre No. 29-1 & 29-2, Jalan Bandar 18, Pusat Bandar Puchong, 47160 Puchong, Selangor, Malaysia WhatsApp: +6016-660 7346 Email: mtmpre@yahoo.com Website: www.mtmpre.com.my Tell us your testing problem. MTM will help you find the right measurement solution.

21 Aug 2026