Factory Laboratory & QC Room Environmental Problems What Should You Measure Malaysia

Factory Laboratory & QC Room Environmental Problems What Should You Measure Malaysia A factory laboratory or QC room may contain precision instruments, samples, chemicals and inspection work. Staff may report: “The room temperature changes too much.” “Humidity may be affecting our samples.” “There is a chemical smell after testing.” “The fume extraction seems weak.” “Our inspection table is not bright enough.” “We need a continuous environmental record.” These are not simply instrument-purchasing questions. They are measurement problems involving: Temperature → Humidity → Data Logging → Airflow → VOC / Relevant Gas → Lighting The correct starting point is: What laboratory activity is being performed, and which environmental condition needs to be controlled or investigated? 1. Start With the Laboratory Activity Different laboratories have different requirements. Ask: What testing is performed? What instruments are used? Are chemicals involved? Are samples sensitive to temperature or humidity? Is ventilation or extraction installed? Are there manufacturer environmental requirements? Is continuous monitoring required? Is the problem related to safety, measurement quality or both? The measurement strategy should follow the laboratory activity. 2. Temperature Can Affect More Than Comfort In a normal office, temperature may mainly be a comfort issue. In a laboratory, temperature can also matter for: Samples Instruments Test repeatability Storage Process conditions Therefore, the question may not simply be: “Is the room comfortable?” It may be: “Is the laboratory staying within the required environmental condition?” 3. One Temperature Reading Is Not Enough for a Changing Room Suppose QC checks the room at: 9:00 AM → 23.5°C Everything appears normal. But conditions may change when: More staff enter Machines operate Afternoon outdoor temperature rises HVAC cycles Doors open frequently A spot measurement does not show the entire day. 4. Use Temperature and Humidity Data Logging A data logger can record: Temperature + Relative Humidity continuously. This helps answer: What was the maximum? What was the minimum? When did conditions change? How long were they outside the desired range? This can be useful for environmental records and troubleshooting. 5. Measure Where the Testing Happens Do not automatically place the logger beside the air-conditioning outlet. The sensor should represent the area of interest. Possible locations include: Test Bench Instrument Area Sample Storage Chemical Area Room Centre Depending on the objective, multiple locations may be useful. 6. Different Parts of the Laboratory Can Behave Differently A laboratory may have: Cold Air Near Supply Diffuser and: Warmer Conditions Near Equipment or: Different Humidity Near Doorways Therefore, environmental mapping may be useful when one location does not represent the whole room. Chemical Use Introduces Another Measurement Problem A QC laboratory may use: Solvents Cleaning chemicals Reagents Adhesives Coatings Sample-preparation chemicals Staff may complain: “There is a chemical smell after we perform this test.” Now the investigation moves from environmental control to safety. 7. Start With the Chemical Do not immediately buy a gas detector. Ask: Which chemical is used? What does the SDS say? When does the smell occur? Is the work performed inside a fume hood? Where does the odour spread? The chemical determines the measurement requirement. 8. VOC Measurement May Be Useful for Suitable Applications Where volatile organic compounds are relevant, a VOC instrument may support suitable screening or comparison. For example: Before Test versus During Test or: Near Workbench versus Reference Area But a general VOC reading does not automatically identify a specific chemical. 9. Specific Hazards Need Appropriate Sensors If the concern is a specific gas or vapour, the measurement method should match that substance. Do not assume: Multi-Gas Detector = Laboratory Chemical Detector A common four-gas detector does not measure every laboratory vapour. Ventilation and Extraction May Be the Real Problem Suppose the laboratory already has extraction. But staff say: “The smell is getting stronger.” Possible causes may include: Weak airflow Filter condition Duct issue Poor hood use Increased chemical activity Changed room pressure This creates a ventilation investigation. 10. Measure Air Velocity An anemometer can help investigate suitable airflow points around: Extraction systems Hood openings Supply air Exhaust Relevant work areas The measurement procedure should match the equipment and objective. 11. Don't Rely Only on Tissue-Paper Tests A quick visual airflow indicator can show that air is moving. But if the question is: “Has extraction performance decreased?” quantitative measurements provide better comparison data. For example: Previous Condition versus Current Condition or: Before Maintenance versus After Maintenance 12. Differential Pressure May Be Relevant Certain laboratory environments or ventilation systems may require pressure relationships between spaces. For suitable applications, differential pressure measurement can help investigate: Room-to-Room Pressure or appropriate: Filter / Ventilation Conditions The required method depends on the facility design. Lighting Is Also Part of QC Quality inspection can involve: Surface inspection Reading scales Checking defects Assembly inspection Visual comparison Fine-detail work Poor illumination can affect inspection conditions. A lux meter can help quantify lighting at the actual inspection surface. 13. Measure at the QC Work Surface Do not measure only at eye level or directly under the lamp. If the task is performed on a table, measure at the representative work plane. Compare: Inspection Bench A Inspection Bench B Sample Preparation Area Instrument Area This helps identify uneven lighting. 14. Environmental Conditions Can Affect Measurement Confidence Suppose a precision instrument has specified operating environmental conditions. If the laboratory moves outside those conditions, this may become relevant to test quality or instrument performance. Therefore, environmental monitoring is not only an EHS issue. It can support: QA / QC + Measurement Control. 15. Example: QC Results Vary in the Afternoon Suppose a factory contacts MTM: “Our QC team notices that some measurements seem less consistent in the afternoon, and the room feels warmer.” A useful first investigation may be: Temperature / Humidity Data Logging ↓ Compare Morning / Afternoon ↓ Compare With Instrument Requirements ↓ Check HVAC / Airflow ↓ Corrective Action ↓ Continue Monitoring This helps determine whether environmental conditions correlate with the problem. 16. Example: Strong Solvent Smell After Sample Preparation Another customer says: “Our laboratory smells strongly of solvent after sample preparation.” Possible pathway: Identify Chemical / SDS ↓ Determine Relevant Vapour ↓ Appropriate VOC / Specific Measurement ↓ Measure Extraction Airflow ↓ Check Work Practice / Ventilation ↓ Corrective Action ↓ Verify This is a laboratory safety measurement solution. 17. Example: Fume Hood Seems Weaker Another customer says: “The fume hood is still running, but suction feels weaker than before.” Possible investigation: Air Velocity ↓ Compare Appropriate Measurement Points ↓ Check Filter / Duct / Fan ↓ Differential Pressure Where Relevant ↓ Maintenance ↓ Measure Again Now the customer has measurable before-and-after information. 18. Example: QA Needs Environmental Records Another factory says: “We need continuous temperature and humidity records for our QC room.” Possible solution: Data Logger ↓ Select Logging Interval ↓ Place at Representative Location ↓ Record Continuously ↓ Review Trends ↓ Maintain Records Where measurement traceability is important, calibration requirements should also be considered. What Instruments Might Be Needed? Depending on the laboratory problem, the solution may include: Temperature & Humidity Meter For environmental spot checks. Temperature & Humidity Data Logger For continuous monitoring. Anemometer For airflow and extraction investigation. Differential Pressure Meter / Digital Manometer For suitable room, filter or ventilation-pressure investigations. VOC Meter For appropriate VOC screening. Specific Gas Detector Where an identified gas requires measurement. Lux Meter For inspection and work-area illumination. Indoor Air Quality Meter For appropriate broader environmental screening. Not every laboratory needs every instrument. The correct combination depends on: Test Process + Chemical + Instrument Requirement + Environmental Problem Don't Search Only for a “Laboratory Environmental Meter” There is no single instrument that answers: Is temperature stable? Is humidity controlled? Is solvent vapour accumulating? Is extraction adequate? Is the QC bench bright enough? These are different measurement questions. From Laboratory Problem to Measurement Solution The better approach is: Identify Laboratory Activity ↓ Identify Environmental / Safety Problem ↓ Determine Required Parameters ↓ Spot Measurement or Continuous Logging ↓ Check Ventilation / Chemical Hazard Where Relevant ↓ Compare With Process Requirements ↓ Correct ↓ Verify Again This is a laboratory measurement system rather than a collection of meters. One Laboratory Can Connect Three MTM Solution Areas Environmental Monitoring Temperature → Humidity → Data Logging Safety VOC / Relevant Gas → Airflow → Ventilation QA / QC Environmental Records → Lux → Measurement Verification This gives MTM another strong factory positioning: EHS does not have to buy from one supplier, QA from another and Maintenance from another. The customer can bring MTM the measurement problem. Factory Laboratory, QC & Environmental Monitoring Solutions Malaysia MTM Precision supports: Manufacturing laboratories QA/QC departments R&D laboratories Factory test rooms Sample preparation rooms EHS departments Facility managers Quality engineers Laboratory technicians with measurement solutions covering: Temperature Humidity Data Logging Airflow Differential Pressure VOC Gas Detection Lux Indoor Air Quality Environmental Monitoring Calibration Support MTM's value is not: “We have many environmental instruments.” It is: “Tell us what is happening in your laboratory or QC room. We help determine what needs to be measured.” Need Help With a Laboratory or QC Environmental Problem? Tell MTM: What testing or inspection are you performing? Are temperature or humidity conditions important? Are chemicals or solvents involved? Is the problem ventilation, smell, lighting or environmental stability? Do you need spot checking or continuous records? We can help identify suitable measurement options for your application. MTM Precision Sdn Bhd Showroom & Service Centre No. 29-1 & 29-2, Jalan Bandar 18, Pusat Bandar Puchong, 47160 Puchong, Selangor, Malaysia WhatsApp: +6016-660 7346 Email: mtmpre@yahoo.com Website: www.mtmpre.com.my Tell us your testing problem. MTM will help you find the right measurement solution.

21 Aug 2026