Cold Room & Freezer Temperature Problems What Should You Measure Malaysia

Cold Room & Freezer Temperature Problems What Should You Measure Malaysia A factory cold room or freezer may appear simple: Set the temperature and keep the door closed. But real operating conditions can be much more complicated. Customers may report: “The controller shows the correct temperature, but some products are not cold enough.” “Temperature rises every time the door opens.” “The upper racks are warmer than the lower racks.” “We want a continuous temperature record.” “One corner of the cold room is always warmer.” “The chiller is running, but temperature recovery is getting slower.” These are not simply: “Thermometer problems.” A proper investigation may involve: Temperature → Data Logging → Temperature Mapping → Humidity → Airflow → Surface Temperature → Time / Door Activity The correct question is: What is happening inside the cold room under real operating conditions? 1. Start With What Is Being Stored Before selecting an instrument, understand the application. Ask: What products are stored? What temperature range is required? Is it a chiller or freezer? How long are products stored? How frequently is the door opened? How large is the room? How high are the racks? Is continuous recording required? Is the concern compliance, quality or troubleshooting? The measurement plan should follow the storage requirement. 2. Controller Temperature Is Only One Measurement Point A customer may say: “Our cold-room display says 4°C, so the entire room should be 4°C.” Not necessarily. The controller sensor measures temperature at a particular location. Actual product-storage areas may differ. Possible differences can occur: Near Evaporator Near Door Upper Rack Lower Rack Rear Corner Centre This is why independent temperature measurement can be valuable. 3. One Thermometer Reading Is Only a Snapshot Suppose the technician opens the cold room and measures: 3.8°C That tells you the temperature: at that location and: at that moment. It does not tell you what happened: One hour earlier During loading Overnight During defrost or after repeated door opening. For changing conditions, data logging becomes much more useful. 4. Use a Temperature Data Logger A logger can record temperature continuously. This helps answer: What was the highest temperature? What was the lowest temperatur? When did the temperature rise? How long did the excursion last? How quickly did the room recover? Now the cold-room discussion changes from: “We think it became warm.” to: “Temperature rose at 2:15 PM and recovered 38 minutes later.” 5. Temperature Mapping Can Reveal Hot and Cold Zones One logger may still not represent the entire room. For suitable investigations, multiple measurement points can be used. For example: Front / Middle / Rear combined with: Low / Middle / High This creates a basic temperature map. 6. Don't Put Every Logger Beside the Cooling Unit The coldest location may be near the evaporator. If every sensor is placed there, the data may not represent the product-storage environment. Sensors should be positioned according to the measurement objective and relevant procedure. 7. Door Opening Can Create Temperature Excursions Cold rooms in active factories may be opened repeatedly for: Receiving Picking Loading Production Stock movement Each opening can introduce warmer air. A useful investigation may compare: Low Door Activity versus Peak Loading Period This can help determine whether operational behaviour contributes to temperature fluctuations. 8. Measure Temperature Recovery Suppose the door remains open during loading. The important question may not only be: How high did temperature rise? It may also be: How long did the cold room take to recover? A logger provides the time history needed to investigate this. 9. Airflow Can Explain Uneven Temperature Suppose: Front racks are cold. Rear racks are warm. The refrigeration system may be operating, but air distribution may be poor. Possible causes include: Products blocking airflow Rack arrangement Evaporator condition Ice buildup Fan problems Poor circulation An anemometer can support airflow investigation where appropriate. 10. Check Airflow at Relevant Locations Depending on the system and safe measurement procedure, investigate appropriate: Supply Air Return Air Rack Area Problem Zone The objective is to determine whether the warmer location also has different air movement. 11. Temperature + Airflow Is More Useful Than Guessing Suppose one corner is consistently warmer. You measure: Higher Temperature and Lower Air Velocity than comparable areas. Now maintenance has a much stronger clue for further investigation. This is the value of combining measurement parameters. 12. Humidity May Also Matter Depending on the stored product and cold-room application, humidity may be relevant. Possible concerns include: Condensation Packaging Product quality Frost Moisture A temperature / humidity logger may therefore be appropriate for some applications. 13. Condensation Is a Symptom A customer may report: “Water droplets appear around the doorway.” That can lead to an environmental investigation involving: Temperature Humidity Door Activity Air Movement rather than simply wiping away the condensation. 14. Surface Temperature Can Answer a Different Question Room air temperature and product or surface temperature are not necessarily identical. An infrared or contact temperature instrument may be useful for appropriate surface-temperature checks. For example: Door Surface Wall Product Packaging Equipment Surface However, surface-temperature measurement should not automatically replace internal product-temperature measurement where that is required. 15. Infrared Thermometers Need Correct Technique Infrared thermometers are convenient, but users should understand: Distance-to-spot ratio Target size Surface characteristics Instrument range Measurement limitations Pointing an IR thermometer from far away at a small object may not give the intended result. 16. Compare Display Reading With Independent Measurement If a customer suspects the cold-room controller reading is incorrect, a useful first step may be to compare it with an appropriate independent instrument. But make sure the measurements represent comparable: Location Time Conditions A sensor near the evaporator and another beside the door should not be expected to read identically. 17. Calibration Matters Cold-room measurements can affect: Product quality Storage records QA/QC Audit documentation Process decisions Therefore, instrument condition and calibration status can be important depending on the application. A logger should not simply be used indefinitely without considering measurement confidence. 18. Example: Controller Says 4°C but Products Feel Warm Suppose a factory contacts MTM: “Our display shows 4°C, but products on the upper rack don't seem cold enough.” Instead of selling another thermometer: Independent Temperature Measurement ↓ Place Loggers at Different Rack Heights ↓ Monitor Full Operating Cycle ↓ Compare Upper / Lower Rack ↓ Check Airflow ↓ Investigate Product Arrangement / Cooling ↓ Corrective Action ↓ Repeat Monitoring This is a cold-room temperature-mapping solution. 19. Example: Temperature Rises During Loading Another customer says: “Every afternoon we receive goods and the cold-room temperature goes up.” Possible pathway: Data Logger ↓ Record Before / During / After Loading ↓ Identify Maximum Temperature ↓ Measure Recovery Time ↓ Compare Door-Open Duration ↓ Investigate Operating Practice / Cooling Performance ↓ Repeat Now the customer has measurable data for the actual event. 20. Example: One Corner Is Always Warmer Another customer says: “The back-right corner is consistently warmer.” Possible investigation: Temperature Mapping ↓ Compare Air Velocity ↓ Inspect Product / Rack Arrangement ↓ Check Cooling-Air Distribution ↓ Corrective Action ↓ Repeat Temperature Mapping This connects environmental monitoring directly to facility troubleshooting. 21. Example: QA Needs a Continuous Record Another customer says: “Our QA department needs to know the cold-room temperature throughout the day.” This is not a spot-thermometer application. A better solution may involve: Temperature Data Logger ↓ Defined Logging Interval ↓ Continuous Recording ↓ Download / Review Data ↓ Maintain Records Depending on the application, calibration and documentation requirements should also be considered. What Instruments Might Be Needed? Depending on the problem, a cold-room measurement solution may include: Digital Thermometer For appropriate spot-temperature measurements. Temperature Data Logger For continuous temperature monitoring. Temperature & Humidity Data Logger Where both environmental parameters are relevant. Multi-Point Data Logging Solution For suitable temperature-mapping applications. Anemometer For airflow investigation. Infrared Thermometer For appropriate non-contact surface-temperature checks. Contact Temperature Instrument For suitable contact measurements. Not every cold room requires every instrument. The correct combination depends on: Product + Storage Requirement + Room Size + Problem + Monitoring Objective Don't Search Only for a “Cold Room Thermometer” A cold-room problem can involve: Incorrect Display Reading Temperature Excursion Slow Recovery Uneven Temperature Poor Airflow Humidity Condensation Product Temperature Each is a different measurement question. From Cold-Room Complaint to Measurement Solution The better approach is: Identify Storage Requirement ↓ Identify Problem Location / Time ↓ Spot Measurement or Continuous Logging? ↓ Map Temperature Where Needed ↓ Check Airflow ↓ Investigate Humidity / Condensation Where Relevant ↓ Corrective Action ↓ Repeat Monitoring That is much stronger than simply selling a thermometer. One Cold Room Can Connect Three MTM Solution Areas Environmental Monitoring Temperature → Humidity → Data Logging Facility Troubleshooting Airflow → Temperature Mapping → Surface Temperature QA / QC Continuous Records → Trend → Verification → Calibration The customer does not need to know which product catalogue to search. They only need to tell MTM: “We have a cold-room temperature problem.” Then we help determine what needs to be measured. Cold Room, Freezer & Environmental Monitoring Solutions Malaysia MTM Precision supports: Food factories Manufacturing plants Cold rooms Freezers Chiller rooms Warehouses Laboratories QA/QC departments Facility managers Maintenance teams with measurement solutions covering: Temperature Humidity Temperature Data Logging Temperature Mapping Air Velocity Surface Temperature Environmental Monitoring Measurement Verification Calibration Support MTM's value is not: “We have many thermometers.” It is: “Tell us what is happening inside your cold room. We help determine what needs to be measured, where to measure it and whether continuous monitoring is needed.” Need Help Investigating a Cold Room or Freezer? Tell MTM: What product are you storing? What temperature range do you need? Is the problem temperature fluctuation, uneven cooling, slow recovery, airflow or humidity? Where and when does the problem occur? Do you need spot measurement, data logging or temperature mapping? We can help identify suitable measurement options for your application. MTM Precision Sdn Bhd Showroom & Service Centre No. 29-1 & 29-2, Jalan Bandar 18, Pusat Bandar Puchong, 47160 Puchong, Selangor, Malaysia WhatsApp: +6016-660 7346 Email: mtmpre@yahoo.com Website: www.mtmpre.com.my Tell us your testing problem. MTM will help you find the right measurement solution.

21 Aug 2026