Strange Smell in Factory What Should You Measure to Find the Source Malaysia

Strange Smell in Factory What Should You Measure to Find the Source Malaysia One of the most difficult factory environmental complaints begins with only one sentence: “There is a strange smell in the factory.” Workers may describe it as: “Chemical smell.” “Burning smell.” “Solvent smell.” “Rotten-egg smell.” “Exhaust smell.” “We don't know what it is, but it happens every afternoon.” The immediate reaction is often: “Which gas detector should we buy?” But this is usually too early. A smell is a clue. It is not a measurement parameter. The better investigation is: Where? → When? → Which Process? → Which Chemical? → Possible Source → What Should Be Measured? Depending on the situation, the solution may involve: VOC → Specific Gas → CO → HS → Combustible Gas / LEL → PM → Airflow → Ventilation The instrument comes after the problem is understood. 1. First Question: Where Is the Smell? Start by identifying the location. For example: Production Line Chemical Storage Room Wastewater Area Boiler Room Painting Area Laboratory Warehouse Loading Bay Drain Utility Room Office Beside Production Location immediately gives useful clues. 2. Second Question: When Does It Happen? This can be even more important. Ask: All day? Only when production starts? Only during cleaning? Only when trucks arrive? Only in the afternoon? Only when a particular machine operates? Only when the exhaust system stops? A time pattern can help connect the complaint to a source. 3. Third Question: What Changed? Many factory problems appear after a change. Ask: Was a new chemical introduced? Was production increased? Was a new machine installed? Was the factory layout changed? Was ventilation modified? Was maintenance recently performed? Did the problem begin after a spill? The change may be more informative than the smell itself. 4. Don't Try to Identify a Chemical From Smell Alone Workers may describe an odour as: Sweet Sharp Burning Sour Rotten But smell alone is not a reliable way to identify or quantify an airborne chemical. Instead:/p> Identify Process ↓ Identify Chemical ↓ Review SDS Where Relevant ↓ Determine Measurement Requirement This is a much stronger approach. 5. Ask for the Chemical List or SDS If chemicals are used near the affected area, MTM should ask: “Can you send us the chemical name or SDS?” This can help determine whether the relevant concern involves: VOC Specific toxic gas Flammable vapour Another chemical hazard Then the correct measurement method can be considered. 6. VOC May Be Relevant for Solvent-Type Complaints Suppose workers report: “There is a strong solvent smell near the coating line.” Where VOC screening is appropriate, a VOC instrument may help compare: Process OFF versus Process ON or: Near Process versus Adjacent Area This can help determine whether conditions change with the process. 7. But VOC Does Not Tell You Everything A general VOC meter does not automatically answer: “Which exact chemical is this?” It also does not mean: Every VOC has been individually measured. Understand the capability of the instrument before interpreting the result. 8. Specific Gas Requires the Correct Sensor Suppose the identified hazard is: Hydrogen Sulfide Then the detector needs an appropriate: HS sensor. If the concern is: Carbon Monoxide the detector needs: CO measurement capability. If another specific gas is identified, the measurement solution must match that gas. 9. Multi-Gas Does Not Mean All Gas This is one of the most important messages for factory buyers. A common four-gas detector may monitor: O LEL CO HS That is four specific measurement channels. It does not automatically measure: CO VOC Formaldehyde or every chemical vapour used in the factory. Always check the sensor configuration. 10. Rotten-Egg Smell Near Wastewater? In certain wastewater or process environments, hydrogen sulfide may be a relevant concern. If HS has been identified as a potential hazard, an appropriate detector can support atmospheric monitoring. But the investigation should still consider: Source Location Ventilation Work Activity not only the gas reading. 11. Exhaust Smell Near Loading Bay? Suppose workers inside the warehouse say: “Whenever trucks arrive, exhaust smell enters the building.” Now the investigation may move toward: Vehicle Activity ↓ Relevant Exhaust Parameter ↓ CO Where Appropriate ↓ PM Screening Where Useful ↓ Airflow ↓ Loading Bay / Warehouse Comparison This is a different problem from solvent vapour. 12. Burning Smell Near Machinery? Suppose workers report: “There is a burning smell near the production machine.” Do not automatically search for a gas detector. The source may involve: Electrical equipment Motor overheating Friction Hot surfaces Process material Wiring Lubrication issue The first investigation may involve equipment inspection and appropriate temperature or electrical measurements by qualified personnel. Again: Complaint first. Instrument second. 13. Dusty Smell or Haze? Sometimes workers describe an air problem as: “Smoky” or: “Dusty.” If particulate is suspected, appropriate PM2.5 / PM10 screening may help compare conditions. For example: Machine OFF versus Machine ON or: Near Source versus Worker Area 14. Ventilation Is Often the Missing Piece Imagine a coating process that has operated for years. The same chemical is still used. But workers suddenly start complaining about stronger odour. What changed? Possibly: Extraction performance. This is why an odour investigation should often include ventilation. 15. Measure Air Velocity An anemometer can help investigate appropriate: Local Exhaust Hood Duct Louvre General Ventilation Instead of asking only: “Is the fan running?” ask: “Is the expected airflow actually present?” 16. A Running Exhaust Fan Can Still Perform Poorly Possible causes include: Dirty filter Blocked duct Damaged fan Poor hood position Changed production layout Increased process load Therefore: Fan ON does not automatically mean: Problem solved. 17. Find Out Where the Smell Travels This is a very useful troubleshooting technique. Compare appropriate locations: Source Area ↓ Worker Position ↓ Doorway ↓ Adjacent Production Area ↓ Office / QC Room The question becomes: Where is the contaminant moving? 18. Airflow Direction Can Explain Odour Migration Suppose the chemical process is inside Production Area A. But workers in Area B complain more. Possible reason: Air movement carries the contaminant toward Area B. This means: Source Measurement + Airflow Investigation may be more useful than measuring only one location. 19. Measure When the Smell Actually Happens If workers say: “The smell appears every day around 3 PM.” measurements taken at: 8 AM may miss the problem completely. Try to investigate under the actual operating condition associated with the complaint. 20. Compare Process OFF vs Process ON This can provide powerful troubleshooting information. Process OFF Take appropriate environmental measurements. Process ON Repeat under comparable locations. If conditions change substantially, the process becomes a stronger lead for further investigation. 21. Compare Ventilation OFF vs Normal Operation Only Where Safe and Appropriate Ventilation testing should follow site safety procedures. The goal is not to deliberately create a hazardous environment. Instead, use appropriate measurements and maintenance testing to understand whether the ventilation system is performing as intended. 22. Example: Solvent Smell Near Printing or Coating Process Factory complaint: “Workers smell solvent whenever the coating line operates.” Possible pathway: Identify Chemical ↓ Review SDS ↓ Determine Relevant Vapour / VOC Measurement ↓ Measure Near Process ↓ Compare Adjacent Worker Area ↓ Measure Local Exhaust Air Velocity ↓ Investigate Extraction ↓ Corrective Action ↓ Measure Again Now MTM is solving the process problem. 23. Example: Rotten-Egg Smell Near ETP Customer: “There is a rotten-egg smell near our wastewater area.” Possible pathway: Identify Wastewater Process ↓ Determine Whether HS Is an Identified Hazard ↓ Appropriate HS / Multi-Gas Measurement ↓ Check Work Location ↓ Investigate Ventilation Where Relevant ↓ Corrective Action ↓ Continue Monitoring as Required This connects Water Quality with Safety. 24. Example: Exhaust Smell Inside Warehouse Customer: “Truck exhaust enters the warehouse during loading.” Possible pathway: Identify Vehicle / Fuel ↓ Determine Relevant Parameters ↓ CO Where Appropriate ↓ PM Screening Where Useful ↓ Compare Loading Bay / Warehouse ↓ Measure Airflow ↓ Investigate Idling / Ventilation ↓ Measure Again This connects Logistics with Environmental Monitoring. 25. Example: Smell Appears but Nobody Knows the Source This is one of the most valuable enquiries for MTM. Customer: “We don't know where the smell comes from.” Start with: Location Mapping ↓ Time Pattern ↓ Process Activity ↓ Chemical Inventory ↓ Ventilation ↓ Appropriate Measurements ↓ Narrow Down Source Do not start by selling the most expensive detector. Start by reducing uncertainty. 26. Build a Factory Odour Investigation Map A simple investigation may record: LocationTimeProcess RunningOdour ComplaintMeasurementProduction AMorningNoLowBaselineProduction AAfternoonYesStrongCompareCorridorAfternoonYesMediumCompareQC RoomAfternoonYesMildCompareOutdoorAfternoonNoneReference The exact parameters depend on the suspected source. This turns: “The factory smells bad.” into structured information. What Instruments Might Be Needed? Depending on the suspected source, a solution may include: VOC Meter For suitable VOC screening and comparison. Specific Gas Detector For an identified gas requiring the correct sensor. Multi-Gas Detector Where its installed sensors match the identified hazards. Carbon Monoxide Detector For appropriate CO monitoring. HS Detector Where hydrogen sulfide is an identified concern. Combustible Gas / LEL Detector For appropriate flammable-atmosphere investigations. PM2.5 / PM10 Meter For suitable particulate screening. Anemometer For ventilation and extraction investigation. Temperature Instrument Where overheating or hot equipment may be related to the complaint. Not every odour complaint needs every instrument. The correct combination depends on: Source + Process + Chemical + Location + Time + Ventilation Don't Ask Only “Which Gas Detector Can Detect Smell?” That is the wrong question. There is no universal: Smell Detector for every factory problem. Instead ask: Where does it smell? When? Which process is running? Which chemicals are used? What does the SDS say? Where is the air moving? Then determine what should be measured. From Strange Smell to Measurement Solution The better approach is: Worker Reports Odour ↓ Identify Location ↓ Identify Time Pattern ↓ Identify Process / Chemical ↓ Review SDS Where Relevant ↓ Determine Possible Gas / VOC / PM / Equipment Source ↓ Measure Appropriate Parameters ↓ Check Ventilation ↓ Locate Source / Migration Path ↓ Corrective Action ↓ Measure Again This is a factory environmental investigation. One “Strange Smell” Complaint Can Connect Multiple MTM Solutions Chemical Safety VOC → Specific Gas → LEL Where Relevant Environmental PM → Air Quality → Location Comparison Ventilation Air Velocity → Extraction → Air Movement Industrial Maintenance Equipment Temperature → Overheating Investigation Where Relevant This is exactly why MTM should not present itself as: “A company with hundreds of meters.” The stronger position is: “A company that helps factories determine what needs to be measured.” Factory Odour, Gas & Air Quality Investigation Solutions Malaysia MTM Precision supports: Manufacturing plants Chemical-handling areas Production lines Coating and painting areas Warehouses Loading bays Wastewater facilities Laboratories EHS departments Safety officers Facility managers with measurement solutions covering: VOC Gas Detection CO HS LEL PM2.5 / PM10 Airflow Ventilation Temperature Environmental Monitoring MTM's value is not: “Which gas detector would you like?” It is: “Tell us where the smell occurs, when it happens and what process is running. MTM helps determine what should be measured.” Strange Smell Somewhere in Your Factory? You do not need to know the detector model. Tell MTM: Where is the smell? When does it happen? What process is running? Which chemicals are used nearby? Can you provide the SDS? Does the smell spread to another area? Is ventilation or extraction installed? From there, we can help identify suitable measurement options for the investigation. MTM Precision Sdn Bhd Showroom & Service Centre No. 29-1 & 29-2, Jalan Bandar 18, Pusat Bandar Puchong, 47160 Puchong, Selangor, Malaysia WhatsApp: +6016-660 7346 Email: mtmpre@yahoo.com Website: www.mtmpre.com.my Don't start by guessing the gas. Start with the source. Tell MTM what is happening we'll help you determine what needs to be measured.

21 Aug 2026