How to Locate Fiber Optic Cable Fault with Noyafa NF-981 OTDR Malaysia

How to Locate Fiber Optic Cable Fault with Noyafa NF-981 OTDR Malaysia

 

A fiber optic cable can fail even when there is no visible damage from the outside.

 

The problem may be caused by a broken fiber, damaged connector, poor splice, excessive bending or another high-loss event somewhere along the cable route.

 

For technicians in Malaysia, checking a long fiber cable metre by metre is usually impractical.

 

An OTDR (Optical Time Domain Reflectometer) such as the Noyafa NF-981 can help determine approximately where an abnormal event occurs along the fiber.

 

What Can Cause a Fiber Optic Cable Fault?

 

Common causes include:

 

Fiber cable breaks

 

Excessive bending

 

Damaged connectors

 

Dirty connectors

 

Poor fusion splices

 

Mechanical stress

 

Cable crushing

 

Construction damage

 

Water or environmental damage

 

Incorrect installation

 

Damaged patch cords

 

Some problems occur inside buildings and are relatively easy to access.

 

Others may occur hundreds of metres or several kilometres away.

 

This is why distance-based fault location is valuable.

 

Why Use an OTDR?

 

A basic Optical Power Meter can tell you whether optical power is present and help measure received power.

 

However, it normally cannot tell you exactly where along the cable an abnormal event occurs.

 

An OTDR provides another layer of information.

 

It sends optical pulses into the fiber and analyses the returned signal.

 

The resulting OTDR trace can provide information about:

 

Fiber distance

 

Loss events

 

Reflective events

 

Connectors

 

Splices

 

Fiber endpoints

 

Possible breaks

 

This helps technicians narrow down the physical location that requires inspection.

 

Using the Noyafa NF-981 for Fiber Fault Location

 

The Noyafa NF-981 supports OTDR testing at:

 

1310nm and 1550nm

 

Its specified OTDR testing distance reaches up to approximately 60 km, with a specified dynamic range of up to 24/22 dB depending on wavelength.

 

For many FTTH, CCTV, building, campus and industrial fiber networks, this provides a practical portable troubleshooting solution.

 

Step 1: Inspect the Fiber Connection

 

Before performing an OTDR test, inspect the accessible fiber connections.

 

Check for obvious problems such as:

 

Loose connectors

 

Damaged patch cords

 

Excessively bent fiber

 

Contaminated connector interfaces

 

Incorrect connections

 

Fiber connector cleanliness is especially important.

 

A dirty connector can create excessive loss and may also affect the accuracy of the test.

 

Step 2: Connect the Fiber to the OTDR

 

Connect the fiber under test to the appropriate OTDR port.

 

Use the correct fiber connector and adapter.

 

Avoid forcing incompatible connectors together.

 

For more professional testing, a suitable OTDR launch cable can be used between the OTDR and the fiber under test.

 

A launch cable helps the OTDR evaluate events close to the beginning of the link that may otherwise be difficult to analyse because of the OTDR dead zone.

 

Step 3: Select the Test Wavelength

 

The NF-981 supports:

 

1310nm

 

and

 

1550nm

 

For many single-mode fiber troubleshooting jobs, technicians may perform tests at both wavelengths.

 

Why?

 

Certain losses, particularly those related to bending, can behave differently at different wavelengths.

 

Comparing results can therefore provide additional diagnostic information.

 

Step 4: Set the OTDR Test Range

 

Choose a distance range appropriate for the fiber link.

 

If you know that the cable is approximately 2 km long, using a test range reasonably above that distance can help produce a useful trace.

 

If the expected distance is unknown, start with a suitable automatic or larger range and refine the settings after obtaining an initial result.

 

Incorrect range selection can make the trace harder to interpret.

 

Step 5: Start the OTDR Test

 

Run the OTDR measurement.

 

The instrument sends optical pulses through the fiber and analyses the returned backscatter and reflections.

 

After the test, the NF-981 can display information about events detected along the link.

 

Depending on the event, the OTDR may show:

 

Distance

 

Event loss

 

Reflectance

 

Cumulative loss

 

Fiber endpoint

 

These measurements help technicians determine where further physical inspection is required.

 

Step 6: Check the Event Map

 

For technicians who are not yet comfortable interpreting conventional OTDR traces, the intelligent event analysis function can be particularly useful.

 

Instead of relying only on the waveform, the event map presents significant events along the fiber link in a more accessible format.

 

For example, the tester may indicate several events at different distances.

 

A technician can then investigate which event shows abnormal loss or appears to represent the end of the fiber.

 

Example: Fiber Break at 850 Metres

 

Imagine a CCTV network uses approximately 1.2 km of single-mode fiber between two locations.

 

The network suddenly stops communicating.

 

A technician checks the equipment and finds no obvious problem.

 

An OTDR test is then performed from one end.

 

Suppose the trace ends abruptly at approximately:

 

850 metres

 

This strongly suggests that the technician should investigate the cable route around that distance.

 

Instead of inspecting the entire 1.2 km route, the troubleshooting area has been dramatically reduced.

 

The actual physical location must still be correlated with the cable route because OTDR distance represents optical fiber length, not necessarily straight-line geographic distance.

 

Step 7: Use the VFL When Appropriate

 

Once the suspected problem area is identified, the NF-981's built-in Visual Fault Locator can provide additional assistance for accessible fiber sections.

 

A VFL sends visible red light through the fiber.

 

Severe breaks, bends or damaged connections may allow visible red light to escape.

 

This is especially useful for:

 

Patch cords

 

Fiber cabinets

 

Accessible connectors

 

Short fiber sections

 

Fiber identification

 

For long-distance buried cables, the VFL alone is generally not enough.

 

That is where OTDR distance measurement becomes much more valuable.

 

OTDR vs VFL for Fiber Fault Finding

 

Both tools are useful, but they serve different purposes.

 

Visual Fault Locator

 

Best for:

 

Short distances

 

Visible inspection

 

Patch cords

 

Connector problems

 

Accessible fiber

 

OTDR

 

Best for:

 

Long fiber links

 

Distance measurement

 

Hidden cable faults

 

Splice analysis

 

Connector event analysis

 

Fiber break location

 

The Noyafa NF-981 combines both functions in one tester.

 

OTDR vs Optical Power Meter

 

An Optical Power Meter is also an important fiber testing instrument.

 

However, its job is different.

 

An OPM answers:

 

"How much optical power am I receiving?"

 

An OTDR helps answer:

 

"What is happening along the fiber, and approximately where?"

 

For complete troubleshooting, technicians may need both types of information.

 

The NF-981 integrates an Optical Power Meter as well as OTDR functionality.

 

Where Is Fiber Fault Location Useful in Malaysia?

 

FTTH Networks

 

Locate faults between distribution points and subscriber connections.

 

CCTV Systems

 

Troubleshoot long-distance fiber connections used between cameras, network switches and control rooms.

 

Factories

 

Investigate fiber links connecting production areas, control rooms and network infrastructure.

 

Commercial Buildings

 

Check fiber backbone connections between floors and communication rooms.

 

Data Centres

 

Assist with troubleshooting fiber infrastructure between equipment areas.

 

Campus Networks

 

Locate faults on longer fiber links between buildings.

 

Telecommunications

 

Investigate fiber distance, events and abnormal losses during maintenance.

 

Important OTDR Testing Tip: Use a Launch Cable

 

One common mistake is connecting the OTDR directly to the fiber under test and expecting every connector event to be clearly visible.

 

OTDRs have a dead zone after strong reflective events.

 

This can make the first connector difficult to evaluate properly.

 

Using an appropriate launch cable creates additional fiber distance between the OTDR and the first connector of the link.

 

For technicians performing professional acceptance testing, a receive cable at the far end may also be useful for evaluating the final connector.

 

Can the NF-981 Find Every Fiber Fault?

 

No OTDR should be treated as a device that automatically diagnoses every possible network problem.

 

The OTDR provides measurement data.

 

Technicians still need to interpret the results together with:

 

Cable route information

 

Network design

 

Connector locations

 

Splice locations

 

Splitter configuration

 

Expected fiber length

 

Optical power measurements

 

For complex networks, experience and correct OTDR settings remain important.

 

Why the NF-981 Is Useful for Field Technicians

 

The advantage of the Noyafa NF-981 is not simply its maximum test distance.

 

Its value comes from combining several tools that technicians may need during the same troubleshooting job:

 

OTDR → Locate events by distance

 

OPM → Measure optical power

 

VFL → Visually locate accessible faults

 

Laser Source → Support optical testing

 

RJ45 Wire Map → Check basic Ethernet cable wiring

 

For contractors working with both fiber and copper networks, this multifunction design can reduce the number of separate instruments required in the field.

 

Noyafa NF-981 OTDR Malaysia

 

If your fiber troubleshooting work frequently involves long cables, hidden routes or faults that cannot be identified visually, moving from a basic OPM/VFL to an OTDR can significantly improve diagnostic capability.

 

The Noyafa NF-981 provides a portable option for fiber installation, maintenance and fault-location work in Malaysia.

 

Rather than asking only:

 

"Is the fiber working?"

 

OTDR testing allows technicians to ask the more useful question:

 

"Where along the fiber should I investigate?"

 

Contact MTM Precision

 

For Noyafa NF-981 OTDR Fiber Tester Malaysia, fiber optic testing equipment and technical enquiries, contact MTM Precision.

 

MTM Precision Sdn Bhd

No. 29-1 & 29-2, Jalan Bandar 18,

Pusat Bandar Puchong,

47160 Puchong, Selangor, Malaysia.

 

Website: www.mtmpre.com.my

WhatsApp: +6016-660 7346

Email: mtmpre@yahoo.com


 

24 Aug 2026