Refinery 4 Gas Detector Malaysia Fosensor FS11301 Portable Multi Gas Detector

# Refinery 4 Gas Detector Malaysia Fosensor FS11301 Portable Multi Gas Detector Looking for a professional 4 Gas Detector for refinery applications in Malaysia? The Fosensor FS11301 Portable 4-in-1 Gas Detector is designed for simultaneous monitoring of four gas parameters: EX / LEL + H2S + CO + O2 Fosensor specifically lists Refining as one of the main applications for the FS11301. The detector is available in two versions: FS11301 Natural Diffusion and FS11301 Pump Suction For refinery, petroleum and industrial users, this allows the detector to be selected according to the required gas-monitoring and sampling method. ## Why Use a 4 Gas Detector in a Refinery? Gas-monitoring requirements depend on the hazards identified for each work area and task. A single-gas detector only provides information about the gas it is designed to measure. Where the required atmospheric monitoring includes combustible gas, hydrogen sulphide, carbon monoxide and oxygen, the FS11301 combines all four measurements in one portable detector. The four standard channels are: - EX / Combustible Gas - H2S / Hydrogen Sulphide - CO / Carbon Monoxide - O2 / Oxygen This makes the FS11301 relevant to refinery applications where these four parameters correspond to the required monitoring programme. ## Fosensor FS11301 Gas Measuring Ranges The standard FS11301 configuration provides: | Gas | Measuring Range | Resolution | |---|---:|---:| | EX / LEL | 0100% LEL | 1% LEL | | H2S | 0100 ppm | 1 ppm | | CO | 01000 ppm | 1 ppm | | O2 | 030% VOL | 0.1% VOL | Before selecting the detector, users should confirm that the required gases and measuring ranges match the application. ## What Are the FS11301 Alarm Points? The manufacturer lists the following alarm points: EX / LEL Low Alarm: 20% LEL High Alarm: 50% LEL H2S Low Alarm: 10 ppm High Alarm: 35 ppm CO Low Alarm: 50 ppm High Alarm: 150 ppm O2 Low Alarm: 19.5% VOL High Alarm: 23.5% VOL These are the alarm values listed in the manufacturer's documentation. Users should follow their applicable workplace procedures when setting and interpreting alarm limits. ## Why Monitor LEL in Refinery Applications? The FS11301 provides an EX channel with a measuring range of: 0100% LEL and: 1% LEL resolution This channel provides combustible-gas monitoring as part of the four-gas configuration. Importantly, the FS11301 does not monitor LEL alone. At the same time, the user can also monitor: H2S + CO + O2 where these parameters are required. ## Why Monitor H2S? The standard FS11301 includes an H2S channel with: 0100 ppm measuring range and: 1 ppm resolution For refinery applications where H2S has been identified as a gas requiring monitoring, this provides simultaneous H2S measurement together with LEL, CO and O2. ## Why Monitor Oxygen? The FS11301 oxygen channel measures: 030% VOL with: 0.1% VOL resolution The manufacturer lists: 19.5% VOL as the Low Alarm and: 23.5% VOL as the High Alarm This allows oxygen concentration to be monitored together with the other three standard gas channels. ## Why Monitor CO? The FS11301 carbon monoxide channel provides: 01000 ppm measuring range with: 1 ppm resolution The manufacturer-listed alarm points are: 50 ppm Low Alarm 150 ppm High Alarm Where CO monitoring is part of the required atmospheric testing, the user therefore does not need a separate CO-only instrument to obtain this measurement. ## Natural Diffusion or Pump Suction for Refinery Use? This is one of the most important buying decisions when selecting the FS11301. Both versions monitor the same standard four gases. The key difference is the sampling method. ### Fosensor FS11301 Natural Diffusion The surrounding atmosphere reaches the detector naturally. Specified dimensions: 135 × 68 × 43 mm This configuration should be considered when professional four-gas monitoring is required without active pump sampling. ### Fosensor FS11301 Pump Suction The Pump version actively draws a gas sample toward the detector. Specified dimensions: 150 × 68 × 60 mm This version should be considered when: Active Gas Sampling Is Required The Pump model should therefore be selected according to the testing procedure rather than simply because it is the higher-level version. ## Does Every Refinery User Need Pump Suction? No. A refinery application does not automatically mean that every worker needs a pump-equipped detector. The correct sampling method depends on the work procedure. If active sampling is not required: FS11301 Natural Diffusion may be appropriate

25 Aug 2026