4 Gas Detector for Metallurgy & Metal Industry Malaysia Fosensor FS11301

# 4 Gas Detector for Metallurgy & Metal Industry Malaysia Fosensor FS11301 Looking for a professional 4 Gas Detector for Metallurgy or Metal Industry applications in Malaysia? The Fosensor FS11301 Portable 4-in-1 Gas Detector provides simultaneous monitoring of: EX / LEL + H2S + CO + O2 Fosensor specifically lists Metallurgy among the main applications for the FS11301. The detector is available in two configurations: FS11301 Natural Diffusion and FS11301 Pump Suction This gives industrial safety, EHS, maintenance and engineering teams a choice according to their required gas-monitoring and sampling method. ## Why Use a 4 Gas Detector in Metallurgy? Gas-monitoring requirements in metallurgy and metal-industry workplaces depend on the actual process and identified atmospheric hazards. A single-gas detector only measures its specified gas. Where the required monitoring includes: Combustible Gas / LEL Hydrogen Sulphide / H2S Carbon Monoxide / CO Oxygen / O2 the Fosensor FS11301 combines all four parameters into one portable detector. The detector should therefore be selected according to the actual gases that need to be monitored, rather than simply because the workplace belongs to the metal industry. ## What Gases Does Fosensor FS11301 Measure? The standard FS11301 configuration provides: | Gas | Measuring Range | Resolution | |---|---:|---:| | EX / LEL | 0100% LEL | 1% LEL | | H2S | 0100 ppm | 1 ppm | | CO | 01000 ppm | 1 ppm | | O2 | 030% VOL | 0.1% VOL | This allows four gas parameters to be monitored simultaneously. Before purchasing, users should confirm that these gases and measuring ranges correspond to their actual workplace requirements. ## What Are the Standard Alarm Points? Fosensor lists the following alarm points for the standard FS11301 configuration: EX / LEL Low Alarm: 20% LEL High Alarm: 50% LEL H2S Low Alarm: 10 ppm High Alarm: 35 ppm CO Low Alarm: 50 ppm High Alarm: 150 ppm O2 Low Alarm: 19.5% VOL High Alarm: 23.5% VOL These are manufacturer-listed alarm values. Actual alarm requirements should follow the applicable workplace procedures and safety requirements. ## Why Monitor CO in Metal Industry Applications? The FS11301 includes a carbon monoxide channel with a specified measuring range of: 01000 ppm and: 1 ppm resolution Where CO is one of the gases identified for monitoring, the detector allows the user to measure it simultaneously with: LEL + H2S + O2 This can be more practical than carrying a separate CO-only detector when all four parameters are required. ## Why Monitor Oxygen? The FS11301 oxygen channel measures: 030% VOL with: 0.1% VOL resolution The manufacturer lists: 19.5% VOL Low Alarm and: 23.5% VOL High Alarm Where oxygen monitoring is required together with the ther three standard gas channels, the user can view all four measurements through the same detector. ## Why Monitor LEL? The combustible-gas channel provides: 0100% LEL with: 1% LEL resolution This gives users an EX / LEL measurement together with CO, H2S and O2. However, users should not assume that an LEL channel automatically provides gas-specific identification. If a particular combustible gas needs to be confirmed, tell MTM Precision the exact gas before purchasing. ## Can FS11301 Detect Every Gas in a Steel or Metal Plant? No. This is important. Fosensor lists Metallurgy as an application, but that does not mean the standard FS11301 measures every possible gas associated with metallurgical processes. The standard configuration discussed here specifically monitors: EX / LEL + H2S + CO + O2 If the required gas is outside these four channels, another detector or sensor configuration may be necessary. Tell MTM Precision the gas to be measured before ordering. ## Natural Diffusion or Pump Suction? The FS11301 is available in two versions. Both provide the same standard four-gas combination. The main difference is the sampling method. ### FS11301 Natural Diffusion The surrounding atmosphere reaches the detector naturally. Specified dimensions: 135 × 68 × 43 mm This version should be considered when professional four-gas monitoring is required without active sampling. ### FS11301 Pump Suction The Pump version actively draws a gas sample toward the detector. Specified dimensions: 150 × 68 × 60 mm This version should be considered when the testing procedure requires: Active Gas Sampling ## Is Pump Suction Always Better? No. Pump Suction provides an additional sampling capability, but this does not automatically make it the correct choice for every metallurgical application. If active sampling is not required: FS11301 Natural Diffusion may be sufficient. If active sampling is required: FS11301 Pump Suction should be considered. The correct detector is the one that matches the work procedure. ## Can the Pump Version Convert to Natural Diffusion? Yes. According to the Fosensor operating instructions, the Pump Suction module can be removed and replaced with the Natural Diffusion front cover. The basic procedure is: 1. Remove the four rear screws. 2. Remove the Pump Suction module. 3. Install the Natural Diffusion front cover. 4. Tighten the four screws. The detector can then operate in Natural Diffusion mode. This provides additional flexibility for professional industrial users. ## What Makes FS11301 More Professional? The FS11301 provides more than four current concentration readings. Its alarm-setting functions include: - Low Alarm - High Alarm - STEL - TWA - MAX The detector also provides: - Gas Alarm Records - Curve Graph These functions give users additional monitoring information and help differentiate the FS11301 from a basic economical four-gas detector. ## Does FS11301 HaveSTEL and TWA? Yes. The FS11301 alarm-setting menu includes: STEL and TWA together with Low Alarm, High Alarm and MAX. The appropriate values and interpretation should follow the applicable workplace requirements. ## Multiple Alarm Indications The FS11301 provides several alarm methods: - Audible Alarm - LED Warning - Vibration - Backlight - LCD Alarm Information When an alarm condition occurs, the detector can activate its buzzer, flashing red indicator, backlight and vibration. This gives the operator several simultaneous warning indications. ## Does FS11301 Store Alarm Records? Yes. The detector includes a: Gas Alarm Record function. Users can select the required gas channel and view its corresponding record through the instrument interface. ## Does FS11301 Have a Curve Graph? Yes. The FS11301 provides a: Curve Graph function. Users can browse changes in measured parameters through the detector interface. Alarm records and curve graphs provide additional functionality beyond simply displaying the current gas concentration. ## Is FS11301 Suitable for Steel Plants? Fosensor specifically lists Metallurgy as one of the main applications for the FS11301. A steel-plant application can therefore be evaluated where the required gas monitoring corresponds to: LEL + H2S + CO + O2 However, “steel plant” alone is not enough information to select a detector. The actual gases, measuring ranges, sampling requirements and site procedures must be considered. ## Is FS11301 Suitable for Metal Processing Factories? It depends on the required gases. If the application requires monitoring of the FS11301's standard four channels: EX / LEL + H2S + CO + O2 the detector can be evaluated against those requirements. If another specific gas is required, a different detector may be more appropriate. ## Is FS11301 Suitable for Furnace Areas? Do not select the detector based only on the name of the work area. First identify: Which gases need to be monitored? What measuring ranges are required? Is Natural Diffusion sufficient? Is active sampling required? If the required measurements correspond to the FS11301 specification, the appropriate version can then be considered. ## Is FS11301 Suitable for Confined Space Work? The FS11301 provides simultaneous monitoring of: O2 + LEL + H2S + CO and a Pump Suction configuration is available where active sampling is required. These features make it relevant when evaluating equipment for atmospheric-testing procedures requiring these four parameters and the appropriate sampling method. However, a portable gas detector alone does not determine whether a confined space is safe for entry. Users must follow the applicable risk assessment, sampling, testing and entry procedures. ## Battery and Operating Environment The FS11301 uses a: 3000mAh Lithium Battery Fosensor specifies: Standby Time: >8 hours Charging Time: approximately 4 hours Working Voltage: DC 5V Working Temperature: -20°C to 50°C Working Humidity: 095% RH, non-condensing Charging

25 Aug 2026