OTYWELL G10S CO Gas Detector for Boiler Room & Factory Safety Malaysia
OTYWELL G10S CO Gas Detector for Boiler Room & Factory Safety Malaysia
Carbon monoxide (CO) is a major gas-safety concern in workplaces where fuel is burned or combustion equipment is operated. Because CO is colourless and odourless, workers may not notice its presence without a suitable gas detector.
The OTYWELL G10S-CO Portable Single Gas Detector provides dedicated carbon monoxide monitoring for industrial and workplace safety applications in Malaysia.
Where Can Carbon Monoxide Be Found?
CO can be produced when fuels do not burn completely. Potential applications for CO monitoring include:
Boiler rooms
Generator rooms
Factories and workshops
Engine maintenance areas
Plant rooms
Warehouses using combustion equipment
Confined spaces
Mechanical rooms
Industrial maintenance work
For personnel who specifically need to monitor carbon monoxide, a single-gas CO detector can be a practical alternative to carrying a multi-gas detector when other gases do not need to be measured.
OTYWELL G10S-CO Measuring Range
The G10S-CO configuration supplied for this application has a carbon monoxide measuring range of:
CO: 0–1000 ppm
This makes the instrument suitable for portable CO monitoring across many industrial safety and maintenance applications.
Why Use a Dedicated CO Gas Detector?
A dedicated detector has a straightforward purpose: continuously monitor the target gas and alert the user when the measured concentration reaches the configured alarm conditions.
For technicians who mainly work around combustion equipment, generators or boilers, this can be simpler than purchasing a multi-gas instrument when only CO monitoring is required.
Boiler Room CO Monitoring
Boiler rooms are an important application for CO detection because combustion is part of normal operation.
A portable CO detector can be used by maintenance personnel when entering the area, carrying out inspections or troubleshooting combustion-related equipment.
Gas detection should form part of the site's overall safety procedure rather than being treated as a replacement for ventilation, equipment maintenance or established workplace controls.
Factory Maintenance Applications
The G10S-CO can also support technicians performing maintenance around equipment where combustion gases may be present.
Typical users may include:
Factory maintenance teams
M&E contractors
Safety officers
Facility management teams
Boiler technicians
Generator service companies
Industrial service contractors
For companies managing several types of gas hazards, MTM Precision can also advise whether a single-gas detector or multi-gas detector is more appropriate for the intended application.
G10S-CO vs 4-in-1 Gas Detector
The correct choice depends on what needs to be monitored.
If the requirement is specifically carbon monoxide, the G10S-CO provides a dedicated solution.
For confined-space applications where several hazards must be checked—commonly oxygen deficiency together with toxic or combustible gases—a suitable multi-gas configuration may be required instead.
Customers should therefore identify the target gases, measuring ranges and application before selecting a detector.
Calibration and Testing
Gas detectors are safety instruments and should be maintained according to the manufacturer's instructions and the user's workplace procedures.
OTYWELL advises that instruments are calibrated before shipment and can be supplied with the relevant calibration/test documentation.
Users should also understand the difference between a bump test and calibration. A bump test checks whether the detector responds appropriately to test gas, while calibration adjusts the instrument against a known gas concentration where required.
Gas Sensor Life
Gas sensors are consumable components.
For the G10S configurations being introduced by MTM Precision, the expected sensor life is typically around 2–3 years, subject to the sensor type, operating conditions, exposure and maintenance.
Sensor life should therefore be considered when purchasing and maintaining portable gas detectors.
OTYWELL G10S Gas Options
MTM Precision is developing the G10S range in Malaysia around several dedicated gas configurations:
CO — Carbon Monoxide
H₂S — Hydrogen Sulphide
O₂ — Oxygen
NH₃ — Ammonia
SO₂ — Sulphur Dioxide
This allows customers to select the gas relevant to their actual workplace hazard instead of assuming that every application requires the same detector.
Need Help Selecting a Gas Detector?
Tell MTM Precision:
1. Which gas needs to be detected?
2. What is the application?
3. Is the detector for personal protection, inspection or continuous work?
4. Is one gas sufficient, or are multiple gases involved?
5. Is the instrument intended for confined-space work?
Our team can recommend a suitable configuration based on the application.
Contact MTM Precision
MTM Precision Sdn. Bhd. (744811-A)
Telephone: +603-8080 7172
WhatsApp: +6016-660 7346
Email: mtmpre@yahoo.com / enquiry@mtmpre.com.my
Website: www.mtmpre.com.my
Showroom & Service Centre:
No. 29-1 & 29-2, Jalan Bandar 18,
Pusat Bandar Puchong,
47160 Puchong, Selangor, Malaysia.
MTM Precision supplies gas detection and industrial testing instruments for customers throughout Selangor, Kuala Lumpur, Johor, Penang, Melaka, Negeri Sembilan, Perak, Pahang, Kedah, Perlis, Terengganu, Sarawak and Sabah, Malaysia.
16 Sep 2026
