Anchor Pull-Out Tester for Testing Laboratory and Inspection Company Malaysia

Anchor Pull-Out Tester for Testing Laboratory and Inspection Company Malaysia

 

Professional Anchor Pull-Out Testing Equipment Malaysia

 

Testing laboratories and inspection companies often require more flexibility from an anchor pull-out tester than a contractor purchasing equipment for one specific project.

 

A professional testing company may receive enquiries involving different anchor types, diameters, applications and required test loads.

 

These can include:

 

Chemical anchors

 

Mechanical anchors

 

Expansion bolts

 

Anchor rods

 

Threaded rods

 

Post-installed steel bars

 

Façade anchors

 

Curtain wall anchors

 

Structural fixings

 

For this type of professional field testing, the Langry APT200 Anchor Pull-Out Tester provides a maximum measurement range of 0–200kN, approximately equivalent to a 20-ton class pull-out testing system.

 

Why Testing Companies Need Flexible Pull-Out Testing Equipment

 

A contractor may know exactly what anchor system is used on a particular project.

 

An independent testing company has a different challenge.

 

Today, the customer may request testing of an expansion bolt.

 

Tomorrow, another project may involve a chemical anchor.

 

The next enquiry may involve façade anchors or post-installed steel bars.

 

This means testing companies should consider not only today's application but also the range of work they expect to accept in the future.

 

Langry APT200 – 200kN Testing Capacity

 

The Langry APT200 provides:

 

Measurement Range: 0–200kN

 

This corresponds to approximately:

 

20-ton class capacity

 

The 200kN range can provide useful flexibility for laboratories and inspection companies whose test requirements may exceed the capacity of a smaller 100kN system.

 

Langry APT200 Technical Specifications

 

SpecificationLangry APT200Measurement Range0–200kNApproximate Capacity20 TonCylinder Centre Hole35mmCylinder Stroke70mmCylinder WeightApprox. 13kgCommon AnchorageΦ6–Φ25Pull RodM24ConverterM6–M22Data Storage500 RecordsContinuous Working Time>200 HoursAccuracy ClassificationEN ISO 7500-1 Class 1

 

These characteristics make the APT200 relevant to professional on-site anchor testing applications.

 

Why 200kN Can Be a Useful Range for Inspection Companies

 

An inspection company should consider the maximum test load it is likely to encounter.

 

A 100kN tester can be sufficient for lower-load applications.

 

However, once a customer's required test exceeds 100kN, that equipment no longer provides sufficient range.

 

The 200kN APT200 provides additional capacity without immediately moving to a 300kN system.

 

For companies serving multiple customers, this can expand the range of projects they are able to consider.

 

When Is 100kN Enough?

 

The Langry APT100 may be suitable when:

 

All expected test loads remain below 100kN

 

The company mainly handles lighter anchors

 

Portability is a high priority

 

Higher-load testing is rarely requested

 

If the testing laboratory knows its work will remain comfortably within this range, a 100kN model may be sufficient.

 

When Should a Testing Company Consider 300kN?

 

The Langry APT300 should be considered when the company's work can require test loads above 200kN.

 

This may apply to specialist companies handling heavier anchoring applications.

 

However, additional capacity should be purchased because it is genuinely required—not simply because 300kN is the largest option.

 

APT100 vs APT200 vs APT300 for Testing Companies

 

ModelMaximum RangeApproximate CapacityGeneral PositionAPT100100kN10 TonLower-load applicationsAPT200200kN20 TonBroad middle rangeAPT300300kN30 TonHigher-load applications

 

A laboratory should review its existing and anticipated customer requirements before choosing.

 

Chemical Anchor Testing Services

 

Testing companies may receive requests to verify chemical or bonded anchor installations.

 

The performance of these anchors can depend on:

 

Drilling

 

Hole diameter

 

Hole cleaning

 

Embedment depth

 

Adhesive installation

 

Adhesive curing

 

Concrete condition

 

Workmanship

 

Where required by the project, the tester can be used to apply the specified tensile test load to selected anchors.

 

Mechanical Anchor and Expansion Bolt Testing

 

Mechanical anchors may also require field verification.

 

Potential factors affecting performance include:

 

Hole diameter

 

Embedment

 

Installation torque

 

Expansion setting

 

Concrete condition

 

Edge distance

 

Anchor spacing

 

Installation workmanship

 

The Langry APT200 can be used for suitable pull-out testing configurations where the required load remains within 200kN.

 

Façade and Curtain Wall Inspection

 

Façade projects can create significant demand for anchor inspection and testing.

 

Testing companies may be appointed to verify selected anchors associated with:

 

Curtain wall brackets

 

Façade supports

 

Cladding systems

 

Chemical anchors

 

Expansion anchors

 

Structural fixings

 

Because test points may be spread throughout a building, portable field equipment is important.

 

Post-Installed Steel Bar Testing

 

Some construction and retrofit projects may require suitable post-installed steel bars or anchoring elements to undergo pull-out verification.

 

Before accepting such a job, the testing company should confirm:

 

Bar diameter

 

Required test load

 

Pulling connection

 

Available exposed length

 

Reaction arrangement

 

Project test method

 

The term “rebar pull-out test” can refer to different test objectives, so the exact requirement should always be clarified.

 

Measurement Accuracy Matters

 

Testing companies sell measurement and inspection services.

 

Therefore, equipment accuracy is an important consideration.

 

The Langry APT200 is specified with an:

 

EN ISO 7500-1 Class 1 accuracy classification

 

However, the testing company should still confirm any project-specific calibration and traceability requirements before performing the work.

 

Calibration Requirements for Professional Testing

 

Some customers may ask:

 

“Is your pull-out tester calibrated?”

 

Testing companies should be prepared for this question.

 

Depending on the project, documentation requirements may include:

 

Equipment identification

 

Serial number

 

Calibration certificate

 

Calibration date

 

Calibration validity

 

Measurement traceability

 

The exact requirement depends on the contract, project specification and customer's QA/QC procedure.

 

Why Calibration Records Matter

 

If a test result is challenged later, the testing company should be able to identify which instrument was used.

 

A professional report may therefore record:

 

Equipment manufacturer

 

Model

 

Serial number

 

Measurement range

 

Calibration information

 

Test date

 

This improves traceability.

 

Why Data Storage Is Useful for Testing Companies

 

The Langry APT series supports storage of up to 500 measurement records.

 

This is useful when testing many anchors during a project.

 

However, stored readings should not replace a complete test report.

 

The testing company may still need to record:

 

Project

 

Location

 

Anchor ID

 

Anchor type

 

Required load

 

Maximum applied load

 

Holding time

 

Observations

 

Result

 

Photographs

 

Test Reporting Is Part of the Service

 

A testing company does not simply provide a number.

 

Customers normally need a usable test record.

 

A professional anchor pull-out test report may include:

 

Project Details

 

Project name, location, contractor and test date.

 

Anchor Details

 

Type, diameter, installation and location.

 

Equipment Details

 

Tester model, serial number and calibration information where required.

 

Test Requirement

 

Specified proof load and loading procedure.

 

Results

 

Actual applied force and observations.

 

Acceptance

 

Pass/fail according to the defined project criteria.

 

Force Measurement Is Not the Same as Engineering Acceptance

 

This distinction is especially important for independent testing companies.

 

The instrument measures the force.

 

For example:

 

Maximum Applied Load: 125.6kN

 

But whether that anchor passes depends on the approved acceptance criteria.

 

The testing company should avoid inventing its own acceptance limit unless it is responsible and authorised to define the test method.

 

Proof Testing vs Ultimate Testing

 

Testing companies should establish the required test objective before mobilising to site.

 

Proof Test

 

The anchor is loaded to a predetermined level according to the approved procedure.

 

The objective is normally not to intentionally cause failure.

 

Ultimate Test

 

The test continues according to a defined method until a failure criterion is reached.

 

This may be destructive.

 

The equipment, safety controls and reporting requirements may differ significantly between these two test types.

 

Why Site Setup Matters

 

A laboratory-quality force indicator does not guarantee a good field test if the physical setup is poor.

 

The operator should consider:

 

Pulling alignment

 

Adapter connection

 

Reaction arrangement

 

Concrete condition

 

Anchor location

 

Edge distance

 

Available clearance

 

Safety zone

 

Good testing practice requires both suitable measurement equipment and an appropriate mechanical setup.

 

Importance of Operator Training

 

Professional testing equipment should be operated by personnel who understand:

 

Hydraulic loading

 

Test setup

 

Equipment limitations

 

Anchor connections

 

Force readings

 

Safety precautions

 

Test documentation

 

An experienced operator is particularly important when testing at high loads.

 

Safety for Professional Pull-Out Testing

 

A 200kN pull-out system can generate substantial tensile force.

 

Testing companies should establish appropriate safety procedures.

 

These may include:

 

Equipment inspection

 

Correct PPE

 

Controlled test area

 

Secure adapters

 

Proper alignment

 

Stable reaction setup

 

Exclusion from the potential failure path

 

Controlled pressure release

 

Safety should be considered during every test, regardless of whether the required load is below the maximum equipment capacity.

 

Building an Anchor Pull-Out Testing Service

 

For an inspection company considering adding anchor pull-out testing to its services, equipment selection is only one part of the setup.

 

The company should also consider:

 

Testing equipment

 

Required capacities

 

Adapters and accessories

 

Calibration

 

Operator training

 

Method statements

 

Safety procedures

 

Test report templates

 

Equipment maintenance

 

Customer application review

 

This creates a more professional service than simply purchasing a hydraulic tester.

 

Why APT200 May Be a Good Starting Point

 

For a testing company that expects a variety of normal construction anchor applications, the APT200 can be an attractive middle-capacity model.

 

It provides:

 

Up to 200kN measurement range

 

Approximately 20-ton class capacity

 

Digital force measurement

 

Data storage

 

Portable field use

 

More range than a 100kN system

 

However, companies expecting regular loads above 200kN should consider the APT300.

 

Can Anchor Pull-Out Testing Become a Service Business?

 

For inspection companies, the equipment can support paid testing services across different industries and projects.

 

Potential customers include:

 

Main contractors

 

Façade contractors

 

Structural contractors

 

M&E contractors

 

Anchor installers

 

Engineering consultants

 

Building owners

 

Infrastructure contractors

 

Companies that already provide construction inspection services may be able to integrate anchor pull-out testing into their existing QA/QC offering.

 

Questions to Ask a Customer Before Accepting a Test Job

 

Before mobilising equipment, ask:

 

What type of anchor is being tested?

 

What is the anchor diameter?

 

What is the required test load?

 

Is this proof testing or destructive testing?

 

What is the test method?

 

What are the acceptance criteria?

 

How many anchors need testing?

 

Where are the anchors located?

 

Is working at height required?

 

What report and calibration documents are required?

 

These questions can prevent major problems at the site.

 

Frequently Asked Questions

 

Is the Langry APT200 suitable for testing companies?

 

It can be a practical option for professional users requiring suitable anchor pull-out testing up to 200kN.

 

Why might a testing laboratory choose 200kN instead of 100kN?

 

The additional range allows the company to consider projects requiring loads above 100kN.

 

Does the APT200 store test readings?

 

The Langry APT series supports storage of up to 500 measurement records.

 

Is calibration important?

 

For professional testing services, calibration and measurement traceability may be required depending on the project or customer.

 

Can the APT200 test chemical anchors?

 

Yes, for suitable chemical anchor testing configurations within its capacity.

 

Can it be used for curtain wall inspection?

 

Yes. Pull-out testing can be applicable to suitable façade and curtain wall anchoring systems where specified.

 

Can a testing company decide whether an anchor passes?

 

The result should be evaluated against the approved project acceptance criteria. The force reading alone does not define pass or fail.

 

Where can a testing company buy the Langry APT200 in Malaysia?

 

Contact MTM Precision Sdn. Bhd. for Langry anchor pull-out testing equipment, quotations and model-selection assistance in Malaysia.

 

Anchor Pull-Out Testing Equipment Supplier Malaysia

 

MTM Precision supplies professional testing and measurement instruments for construction, civil engineering, inspection and industrial applications.

 

For testing laboratories and inspection companies, we recommend providing:

 

Anchor Type + Diameter + Maximum Required Test Load + Typical Application

 

This helps determine whether APT100, APT200 or APT300 provides the appropriate testing range.

 

Contact MTM Precision

 

MTM Precision Sdn. Bhd.

 

Showroom & Service Centre

 

No. 29-1 & 29-2, Jalan Bandar 18,

Pusat Bandar Puchong,

47160 Puchong, Selangor, Malaysia

 

🌐 Website: www.mtmpre.com.my

📧 Email: mtmpre@yahoo.com

📱 WhatsApp: +6016-660 7346

 

For Langry APT200 Anchor Pull-Out Tester for Testing Laboratory and Inspection Company Malaysia, current quotation, model selection and professional construction testing equipment enquiries, contact MTM Precision.


 

11 Aug 2026