Linshang LS173 Colorimeter for Color Difference and Delta E Measurement Malaysia

Linshang LS173 Colorimeter for Color Difference and Delta E Measurement Malaysia

 

Color consistency is an important quality requirement in many manufacturing industries. A product may be dimensionally correct and function properly, but an obvious difference in color can still result in rejection, rework or customer complaints.

 

The Linshang LS173 D/8 Touch Screen Colorimeter provides manufacturers and quality control teams with an objective method for evaluating color differences using measurable color data, including Delta E (ΔE).

 

Instead of relying only on statements such as “the color looks slightly different,” companies can establish a more consistent color inspection process.

 

What Is Delta E (ΔE)?

 

Delta E, commonly written as ΔE, represents the difference between two measured colors.

 

In a typical quality control process, one sample is established as the standard or reference color, while another sample is measured and compared against it.

 

The resulting ΔE value indicates the degree of color difference between the two.

 

In general:

 

A smaller ΔE indicates a smaller color difference.

 

A larger ΔE indicates a greater color difference.

 

However, the acceptable ΔE tolerance should be determined according to the product, material, customer specification and internal quality requirements.

 

There is no single Delta E limit that is suitable for every industry.

 

Why Measure Color Difference?

 

Imagine receiving two production batches from different suppliers.

 

Under normal factory lighting, both may appear similar.

 

However, when the products are placed side by side under another light source, a difference may become more noticeable.

 

Visual inspection can also vary from one person to another.

 

Using the Linshang LS173 allows QC personnel to compare samples using numerical measurement instead of depending entirely on subjective judgement.

 

Standard Sample vs Production Sample

 

A practical way to use the LS173 is to establish an approved product as the standard.

 

The basic workflow can be:

 

Approved Standard → Measure Sample → Compare Color → Review ΔE → Accept or Reject According to QC Criteria

 

For example, a manufacturer may keep an approved plastic component as its master sample.

 

When a new production batch arrives, the QC team can measure the new component and compare its color against the approved standard.

 

This provides a more repeatable inspection method.

 

Color Difference Measurement for Plastic Manufacturing

 

Plastic products are one of the important applications for portable colorimeters.

 

Color variation can occur because of differences in:

 

Raw materials

 

Pigments

 

Masterbatch

 

Production parameters

 

Supplier batches

 

Processing conditions

 

A colorimeter such as the LS173 can help manufacturers monitor these variations.

 

Applications can include plastic housings, injection-molded components, plastic sheets, consumer products and other colored plastic parts.

 

Paint and Coating Color Inspection

 

Painted and coated products can also experience batch-to-batch variation.

 

A color difference may arise from material formulation, coating thickness, production conditions or application processes.

 

The Linshang LS173 can provide measurable color information for comparing a coated sample with an approved reference.

 

This is useful for production QC as well as supplier and incoming inspection.

 

Printing and Packaging Quality Control

 

Brand colors are important in packaging.

 

If different production batches show noticeable color differences, the packaging may appear inconsistent when displayed together.

 

Color measurement can therefore be useful for checking suitable printed and packaging materials against approved samples.

 

Instead of relying entirely on an operator's visual judgement, QC personnel can use measurement data as an additional inspection reference.

 

Delta E for Supplier Quality Control

 

Color measurement can also improve communication between buyers and suppliers.

 

Statements such as:

 

“The color is too different.”

 

or:

 

“This batch is not the same as the previous batch.”

 

can be subjective.

 

If both parties use defined measurement procedures and agreed tolerances, discussions can become more data-driven.

 

This can be particularly valuable for companies purchasing colored components from multiple suppliers.

 

Incoming Material Inspection

 

Incoming Quality Control, or IQC, is another useful application.

 

Before incoming materials are released to production, samples can be compared with the company's approved reference.

 

Potential color deviations can therefore be identified before the material enters the manufacturing process.

 

Early detection may help reduce unnecessary production, rework and material wastage.

 

Production Quality Control

 

The LS173 can also be used during production.

 

Rather than waiting until an entire batch is completed, manufacturers can periodically measure samples during the production process.

 

If color measurements begin to move outside the company's established acceptance criteria, the production team can investigate the cause earlier.

 

This turns color measurement into part of the production control process.

 

Final Product Inspection

 

Before shipment, finished products can be checked again against the required color standard.

 

This is especially useful when appearance is an important acceptance criterion.

 

Measurement records can also provide QC teams with a more consistent method of evaluating different batches over time.

 

Why Not Depend Only on the Human Eye?

 

Human color perception is affected by many factors, including:

 

Lighting

 

Viewing conditions

 

Background color

 

Viewing angle

 

Observer differences

 

Eye fatigue

 

This means two inspectors may not always agree on whether a sample is acceptable.

 

A colorimeter does not eliminate the need for experienced QC personnel, but it provides additional objective information to support their decisions.

 

D/8 Color Measurement

 

The Linshang LS173 uses D/8 optical geometry, referring to diffuse illumination and 8-degree viewing.

 

D/8 geometry is widely associated with instrumental color measurement applications and provides controlled optical conditions for evaluating sample color.

 

For industrial users, this makes the LS173 suitable for establishing a more standardized approach to routine color inspection.

 

Is the Linshang LS173 Suitable for Your Application?

 

The LS173 may be considered by companies involved in:

 

Plastic manufacturing

 

Paint and coating

 

Printing

 

Packaging

 

Consumer products

 

Manufacturing QC

 

Supplier quality control

 

Incoming inspection

 

Production inspection

 

Finished product inspection

 

Before selecting a colorimeter, users should also consider the sample surface, measurement requirements, required color parameters and internal QC specifications.

 

From “Looks Different” to Measurable Color Data

 

The biggest advantage of instrumental color measurement is not simply obtaining another number.

 

It is about improving consistency.

 

Instead of:

 

“This looks slightly darker.”

 

QC personnel can work with measurable color information.

 

Instead of:

 

“I think this batch is acceptable.”

 

companies can establish defined measurement procedures and acceptance criteria.

 

This helps create a more systematic approach to color quality control.

 

Linshang LS173 Colorimeter Malaysia

 

MTM Precision supplies industrial testing and measurement instruments for manufacturing, engineering and quality control applications in Malaysia.

 

If you need a colorimeter for Delta E measurement, color difference inspection, incoming QC or production color control, contact MTM Precision to discuss your application.

 

Contact MTM Precision

 

MTM Precision Sdn. Bhd.

 

Showroom & Service Centre

 

No. 29-1 & 29-2, Jalan Bandar 18,

Pusat Bandar Puchong,

47160 Puchong, Selangor, Malaysia

 

🌐 Website: www.mtmpre.com.my

📧 Email: mtmpre@yahoo.com

📱 WhatsApp: +6016-660 7346

 

Need a Linshang LS173 Colorimeter for Delta E and color difference measurement? Contact MTM Precision for quotation and product enquiries in Malaysia.


 

12 Aug 2026