Linshang LS173 Colorimeter for Plastic Color Measurement Malaysia

Linshang LS173 Colorimeter for Plastic Color Measurement Malaysia

 

Color consistency is a major quality requirement in plastic manufacturing. Injection-molded parts, plastic housings, sheets, panels and consumer products may look similar at first glance, but even small color variations between production batches can create quality issues.

 

The Linshang LS173 D/8 Touch Screen Colorimeter provides plastic manufacturers and quality control teams with an objective method for measuring product color and evaluating color differences.

 

For Malaysian manufacturers that currently rely mainly on visual comparison, the LS173 can help establish a more consistent and measurable color inspection process.

 

Why Does Plastic Color Vary?

 

Plastic color can be affected by many factors throughout the manufacturing process.

 

Common causes include:

 

Different raw material batches

 

Resin variation

 

Pigment concentration

 

Masterbatch variation

 

Mixing ratio

 

Processing temperature

 

Injection molding parameters

 

Different material suppliers

 

Recycled material content

 

Production conditions

 

Even when the same color specification is used, the finished components may not always appear identical.

 

This is why instrumental color measurement can be valuable for plastic manufacturing QC.

 

From Visual Comparison to Measurable Data

 

A common plastic QC method is to place a production sample beside an approved sample and visually compare them.

 

This is simple, but the result can depend on the operator and inspection environment.

 

One inspector may say:

 

“The color is acceptable.”

 

Another may say:

 

“This batch looks slightly darker.”

 

The Linshang LS173 allows the QC team to obtain numerical color measurement data and evaluate the difference between the reference and production sample.

 

This reduces dependence on subjective descriptions.

 

Using a Master Plastic Sample

 

A practical QC procedure begins with an approved master sample.

 

For example, a plastic manufacturer may keep a customer-approved injection-molded component as the reference.

 

Production samples can then be measured and compared against this standard.

 

The workflow can be:

 

Approved Master Sample → Measure Production Sample → Compare Color Data → Check Color Difference → Accept or Investigate

 

This creates a repeatable inspection process for different production batches.

 

Delta E Measurement for Plastic Products

 

Delta E (ΔE) is commonly used to express the difference between two measured colors.

 

In general:

 

Lower ΔE = smaller color difference

 

Higher ΔE = larger color difference

 

Manufacturers can use this information when comparing a plastic sample against an approved standard.

 

However, the acceptable Delta E tolerance depends on the product and customer requirements.

 

A company producing decorative consumer products, for example, may establish different acceptance criteria from a manufacturer producing hidden internal components.

 

Therefore, Delta E should be used together with an appropriate QC specification.

 

Plastic Injection Molding Applications

 

Injection molding companies may produce thousands of components in a single production run.

 

Color variation can become costly if the problem is discovered only after the entire batch has been completed.

 

The LS173 can be incorporated into routine production inspection for suitable plastic components such as:

 

Electrical housings

 

Appliance components

 

Automotive plastic parts

 

Plastic covers

 

Plastic panels

 

Consumer product housings

 

Industrial plastic components

 

Molded accessories

 

Periodic measurement can help identify color changes earlier during production.

 

Incoming Raw Material Inspection

 

Color control can begin before molding.

 

If a manufacturer receives colored materials or components from suppliers, the incoming QC team can compare suitable samples against approved references.

 

This may help identify supplier or batch variation before the material is released to production.

 

For companies working with multiple suppliers, objective color measurement can also improve supplier quality management.

 

Masterbatch and Pigment Quality Control

 

Pigment and masterbatch selection directly affects the appearance of finished plastic products.

 

When trial samples are produced, color measurement can provide useful numerical information for comparing different formulations or batches.

 

Instead of relying only on statements such as:

 

“Add slightly more blue.”

 

or:

 

“This sample is almost correct.”

 

the development and QC teams can use measured color differences to support their evaluation.

 

Production Process Monitoring

 

Color measurement can also become part of In-Process Quality Control (IPQC).

 

Rather than measuring only the first and last pieces of a production run, samples can be checked periodically.

 

For example:

 

Start of Production → Sample Measurement → Mid-Batch Check → Sample Measurement → Final Batch Check

 

If color variation begins increasing during production, the team can investigate possible causes before producing a large quantity of non-conforming components.

 

Supplier-to-Supplier Color Comparison

 

Some manufacturers purchase similar plastic parts from several suppliers.

 

Although every supplier may receive the same color specification, the actual products can still show variation.

 

The LS173 can help purchasing and supplier quality teams compare samples from Supplier A, Supplier B and Supplier C against the same approved reference.

 

This creates a more objective basis for supplier evaluation.

 

Why D/8 Geometry Matters

 

The Linshang LS173 uses D/8 measurement geometry, referring to diffuse illumination with 8-degree viewing.

 

Controlled optical geometry helps provide a more standardized approach to color measurement.

 

For plastic manufacturers, this is useful when measurements need to be repeated by different operators or across different production batches.

 

Touch Screen Operation for Routine QC

 

A colorimeter used in manufacturing should not be unnecessarily complicated for everyday inspection.

 

The LS173's touch screen design provides convenient access to measurement information and supports routine color comparison work.

 

This makes it suitable for QC personnel who need to perform repeated measurements throughout the working day.

 

Reduce Rework and Rejection

 

A color problem discovered early may involve only a small quantity of material.

 

The same problem discovered after thousands of components have been produced can become much more expensive.

 

Routine color measurement can therefore support efforts to reduce:

 

Rejected batches

 

Customer complaints

 

Sorting work

 

Rework

 

Scrap

 

Material wastage

 

Production delays

 

The objective is not simply to measure color—it is to detect variation before it becomes a larger production problem.

 

Applications in Malaysian Plastic Manufacturing

 

The Linshang LS173 may be considered by companies involved in:

 

Plastic injection molding

 

Plastic component manufacturing

 

Consumer products

 

Electrical and electronic housings

 

Automotive components

 

Packaging

 

Plastic sheets and panels

 

Industrial plastic products

 

Supplier quality inspection

 

Manufacturing QC

 

Is the Linshang LS173 Suitable for Your Plastic Sample?

 

Before selecting a colorimeter, it is important to consider the actual sample being measured.

 

Factors such as surface characteristics, sample shape, measurement area and required QC criteria can affect instrument selection.

 

If possible, provide information about your sample and measurement requirement before purchasing.

 

This allows the appropriate color measurement solution to be evaluated for the application.

 

Linshang LS173 Colorimeter Supplier for Plastic Industry Malaysia

 

MTM Precision supplies industrial testing and measurement instruments for manufacturers, engineering companies and quality control departments in Malaysia.

 

If you are looking for a colorimeter for plastic color measurement, Delta E inspection, masterbatch comparison, injection molding QC or batch color consistency, contact MTM Precision to discuss your application.

 

Contact MTM Precision

 

MTM Precision Sdn. Bhd.

 

Showroom & Service Centre

 

No. 29-1 & 29-2, Jalan Bandar 18,

Pusat Bandar Puchong,

47160 Puchong, Selangor, Malaysia

 

🌐 Website: www.mtmpre.com.my

📧 Email: mtmpre@yahoo.com

📱 WhatsApp: +6016-660 7346

 

Need a Linshang LS173 Colorimeter for plastic color measurement in Malaysia? Contact MTM Precision for quotation, product information and application enquiries.


 

12 Aug 2026