How to Measure Solar Irradiance with TENMARS TM-751 Malaysia

How to Measure Solar Irradiance with TENMARS TM-751 Malaysia

 

Solar irradiance measurement is useful for solar PV installation, site inspection, panel positioning, maintenance and general solar energy assessment.

 

Instead of estimating sunlight intensity based only on weather conditions or visual observation, technicians can use a solar power meter such as the TENMARS TM-751 to obtain an actual solar radiation reading in W/m².

 

For solar contractors and engineers in Malaysia, understanding how to take consistent solar irradiance measurements can help improve site evaluation and troubleshooting.

 

What Is Solar Irradiance?

 

Solar irradiance describes the amount of solar power received over a particular surface area.

 

It is commonly expressed in:

 

W/m² — watts per square metre

 

The reading can change significantly depending on environmental and measurement conditions.

 

For example, solar irradiance measured under strong direct sunlight will normally be considerably higher than a measurement taken under heavy cloud cover.

 

Other factors such as panel orientation, shading and sensor angle can also affect the measurement.

 

Why Measure Solar Irradiance?

 

Solar PV systems depend on incoming solar energy.

 

When evaluating a photovoltaic installation, technicians may therefore need to understand whether the available sunlight at the time of inspection is sufficient for meaningful performance assessment.

 

Solar irradiance measurement can be useful for:

 

Solar PV site surveys

 

Installation checks

 

Panel orientation comparisons

 

Maintenance inspections

 

Performance troubleshooting

 

Shading investigation

 

Solar radiation surveys

 

Training and demonstration

 

Instead of simply recording that the weather is "sunny", the technician can record an actual irradiance value.

 

Using the TENMARS TM-751

 

The TENMARS TM-751 Solar Power Meter is designed for portable solar radiation measurements.

 

It offers a measurement range of up to:

 

2000 W/m²

 

with a resolution of:

 

0.1 W/m²

 

Its approximately 0.25-second sampling rate also allows technicians to observe changes in solar radiation relatively quickly while adjusting the measurement position.

 

This is particularly useful when comparing different panel angles or locations.

 

Step 1: Select a Suitable Measurement Location

 

Before taking the reading, identify the location that represents the condition you want to evaluate.

 

For solar PV applications, this will normally be near the solar panel array or installation area.

 

Avoid unintentionally positioning the meter where nearby structures create shadows that are not representative of the panel conditions.

 

Possible sources of shading include:

 

Roof structures

 

Water tanks

 

Trees

 

Utility poles

 

Antennas

 

Adjacent buildings

 

HVAC equipment

 

If shading itself is what you are investigating, take measurements at both shaded and unshaded locations for comparison.

 

Step 2: Position the Sensor Correctly

 

Sensor orientation is important when measuring solar radiation.

 

For a general sunlight measurement, expose the sensor directly to the sunlight according to the instrument's operating requirements.

 

For solar PV comparison work, positioning the sensor in approximately the same plane as the solar panel can provide a more relevant comparison with the radiation reaching the panel surface.

 

Small changes in angle may produce different readings.

 

Therefore, technicians should maintain consistent sensor positioning when comparing multiple locations or panels.

 

Step 3: Allow the Reading to Stabilise

 

Once the sensor is positioned, observe the display.

 

Sunlight can fluctuate because of moving clouds, atmospheric conditions and shadows.

 

Rather than recording a rapidly changing instantaneous value without context, allow the measurement to stabilise sufficiently for the application.

 

If conditions are changing quickly, record several readings.

 

For example:

 

Measurement 1: 820 W/m²

Measurement 2: 845 W/m²

Measurement 3: 831 W/m²

 

This provides more useful information than simply describing the conditions as "bright sunlight".

 

Step 4: Record the Measurement Conditions

 

A W/m² reading becomes more valuable when accompanied by basic site information.

 

Consider recording:

 

Solar irradiance reading

 

Date

 

Time

 

Location

 

Weather condition

 

Panel orientation

 

Panel angle

 

Shading condition

 

Relevant system measurements

 

This allows technicians to compare measurements taken during future maintenance visits.

 

Step 5: Compare Different Solar Panel Positions

 

One useful application of the TENMARS TM-751 is comparing solar radiation at different angles.

 

For example, a technician can measure irradiance at one panel orientation and then repeat the measurement at another orientation.

 

If the first position measures:

 

650 W/m²

 

and another position measures:

 

890 W/m²

 

under otherwise similar conditions, the difference indicates that the second orientation is receiving greater solar radiation at that particular time.

 

However, a single measurement should not be treated as the complete basis for designing a solar PV system.

 

Solar position changes throughout the day and year.

 

Professional system design should also consider long-term solar data, site geometry, shading and other engineering factors.

 

Using Irradiance Measurements for Solar PV Troubleshooting

 

Solar irradiance measurements can also provide useful context during photovoltaic troubleshooting.

 

Imagine a technician measures lower-than-expected PV output.

 

Without measuring sunlight, it may be difficult to determine whether the lower output is associated with:

 

Low solar radiation

 

Cloud cover

 

Shading

 

Dirty panels

 

Electrical problems

 

Panel problems

 

Inverter issues

 

System configuration

 

Measuring solar irradiance does not identify every fault automatically.

 

However, it provides an important environmental reference.

 

If solar irradiance is low, reduced PV output may be expected.

 

If solar irradiance is strong but system output is unexpectedly poor, further electrical and system investigation may be required.

 

Irradiance and Shading Inspection

 

Partial shading can significantly influence solar PV performance.

 

The TENMARS TM-751 can be used to compare solar radiation between different positions around an installation.

 

For example, technicians can compare:

 

Unshaded location → W/m²

 

versus

 

Partially shaded location → W/m²

 

This provides measurable evidence of the difference in solar exposure.

 

It can be useful when investigating roofs affected by trees, nearby buildings or rooftop equipment.

 

Why Time of Measurement Matters

 

Solar irradiance changes throughout the day.

 

A reading taken at 9:00 AM cannot automatically be compared directly with another reading taken at 1:00 PM without considering the different solar conditions.

 

For better comparative measurements, technicians should try to keep test conditions as consistent as practical.

 

This is especially important when comparing:

 

Different panels

 

Different roof areas

 

Different panel angles

 

Different solar films

 

Different glass samples

 

Consistent testing produces more meaningful results.

 

Can a Lux Meter Measure Solar Irradiance?

 

A lux meter and a solar power meter measure different quantities.

 

A lux meter measures illuminance, normally expressed in lux.

 

The TENMARS TM-751 measures solar radiation intensity in W/m².

 

Therefore, users evaluating solar energy should select an instrument designed for solar radiation measurement rather than assuming that a lux value can directly replace an irradiance measurement.

 

Applications Beyond Solar Panels

 

Although solar PV is an important application, the TENMARS TM-751 can also be used for comparative solar measurements involving:

 

Automotive windows

 

Window tint

 

Solar control films

 

Building glass

 

Transparent glass

 

Coated glass

 

Solar transmission demonstrations

 

For example, readings can be compared before and after solar radiation passes through a piece of treated glass.

 

This makes the instrument relevant beyond the photovoltaic industry.

 

Common Solar Irradiance Measurement Mistakes

 

Several simple mistakes can make measurements less useful.

 

Avoid:

 

Accidentally shading the sensor with your body

 

Changing sensor angles during comparison tests

 

Comparing measurements taken under very different weather conditions

 

Taking readings at different locations without recording them

 

Confusing W/m² with lux

 

Assuming one instantaneous reading represents the entire day's solar conditions

 

Good measurement practice is just as important as selecting the correct instrument.

 

TENMARS TM-751 for Solar Measurement in Malaysia

 

Malaysia's strong sunlight and expanding use of rooftop photovoltaic systems create many applications for portable solar measurement instruments.

 

The TENMARS TM-751 Solar Power Meter provides engineers, technicians and solar contractors with a straightforward method of measuring solar irradiance directly at the work site.

 

For installation, inspection, troubleshooting or solar radiation comparison, recording actual W/m² values provides more useful information than relying on visual judgement alone.

 

Looking for TENMARS TM-751 Solar Power Meter in Malaysia?

 

MTM Precision supplies professional testing and measurement instruments for solar, electrical, environmental and industrial applications.

 

Contact our team for product enquiries and assistance selecting a suitable solar measurement instrument for your application.

 

Contact MTM Precision

 

MTM Precision Sdn. Bhd.

 

Showroom & Service Centre

 

No. 29-1 & 29-2, Jalan Bandar 18,

Pusat Bandar Puchong,

47160 Puchong, Selangor, Malaysia

 

🌐 Website: www.mtmpre.com.my

📧 Email: mtmpre@yahoo.com

📱 WhatsApp: +6016-660 7346


 

13 Aug 2026