Hot Wire Anemometer for Cleanroom Airflow Testing – TENMARS TM-4002 Malaysia
Hot Wire Anemometer for Cleanroom Airflow Testing – TENMARS TM-4002 Malaysia
Airflow is an important parameter in controlled environments. Cleanroom operators, facility teams and HVAC professionals may need to measure air velocity to evaluate ventilation performance, investigate airflow conditions or support routine maintenance activities.
The TENMARS TM-4002 Hot Wire Anemometer measures air velocity from 0.01 to 25.00 m/s and features a slim telescopic probe, making it suitable for relatively low air velocity measurements in cleanroom and controlled-environment applications.
Why Measure Airflow in a Cleanroom?
Cleanrooms rely on controlled air movement as part of their environmental management systems.
Air velocity measurements may be required when:
Checking ventilation performance
Comparing airflow between locations
Performing HVAC maintenance
Investigating changes in airflow
Checking air supply conditions
Supporting commissioning work
Conducting routine facility inspections
Actual requirements depend on the cleanroom design, applicable standards and the customer's validation procedures.
The TM-4002 provides measurement data that can support these activities, but it should not be assumed to replace any specific certified cleanroom validation procedure.
Why Use a Hot Wire Anemometer?
Hot wire anemometers are useful when relatively low air velocities need to be measured.
Instead of using a rotating vane, a hot wire instrument uses a small thermal sensing element.
The compact sensing design provides an advantage when the measurement point is restricted or when a slim probe is preferred.
The TENMARS TM-4002 measures:
0.01 to 25.00 m/s
with selectable air velocity units including:
m/s
ft/min
km/hr
mph
knots
Telescopic Probe for Difficult Measurement Points
The TM-4002 features a telescopic probe extending approximately from:
400 mm to 1020 mm
This additional reach can be useful when airflow needs to be measured at locations that are difficult to access with a conventional handheld vane anemometer.
It is also useful for measurements inside suitable HVAC and ventilation ducts serving controlled environments.
Measure Airflow at Multiple Locations
Air velocity may vary from one measurement point to another.
Depending on the required testing method, technicians may need to take measurements at multiple positions rather than rely on one reading.
Typical locations may include:
Air supply points
HVAC ducts
Ventilation outlets
Different areas within the controlled space
Return air locations
Multiple readings provide more information about how airflow varies across the system.
CFM and CMM Air Volume Measurement
In addition to air velocity, the TM-4002 supports air volume measurement in:
CFM – Cubic Feet per Minute
CMM – Cubic Metres per Minute
Where the relevant measurement area is known, air volume information can be useful for evaluating ventilation and HVAC performance.
This makes the TM-4002 suitable for broader HVAC work beyond basic air velocity measurement.
Temperature Measurement
Temperature is another important environmental parameter in many controlled facilities.
The TM-4002 provides air temperature measurement together with airflow data.
This allows technicians to observe both the movement and temperature of air at the measurement location.
Relative Humidity Measurement
The TM-4002 also measures relative humidity.
Humidity control can be important in environments such as:
Pharmaceutical facilities
Electronics manufacturing
Laboratories
Controlled production areas
Research facilities
Requirements vary according to the process and facility, so measurements should always be interpreted against the relevant operating specifications.
Dew Point and Wet Bulb Temperature
The TENMARS TM-4002 additionally provides:
Dew point
Wet bulb temperature
These parameters give HVAC and facility professionals additional information about air moisture conditions.
The result is a combination of:
Air Velocity + Air Volume + Temperature + Humidity + Dew Point + Wet Bulb
in one portable instrument.
99 Sets of Manual Data Memory
Controlled-environment inspections may involve multiple measurement locations.
The TM-4002 provides 99 sets of manual data memory, allowing users to retain readings during field work.
This can be useful when comparing:
Multiple air supply points
Different HVAC zones
Several duct locations
Different rooms
Different measurement positions
MAX, MIN and HOLD functions are also available.
Cleanroom and Controlled-Environment Applications
Potential applications for the TM-4002 include:
Pharmaceutical Facilities
Airflow and environmental measurements can support HVAC inspection and facility maintenance activities.
Electronics Manufacturing
Controlled production environments may require monitoring of airflow, temperature and humidity conditions.
Laboratories
The instrument can be used for ventilation and environmental measurement applications.
Medical and Healthcare Facilities
HVAC and facility teams may use airflow instruments when inspecting ventilation systems, subject to the facility's required procedures.
Precision Manufacturing
Controlled manufacturing areas may require stable environmental conditions for certain production processes.
TM-4002 Is Not Only for Cleanrooms
One advantage of choosing the TM-4002 is its versatility.
The same instrument can also be used for:
HVAC duct testing
Air balancing
Air-conditioning maintenance
Building ventilation
Facility management
Industrial ventilation
Laboratory HVAC inspection
This can make the instrument particularly useful for HVAC contractors and facility teams who work across different applications.
Who Should Consider the TM-4002?
Potential users include:
Cleanroom contractors
HVAC contractors
M&E contractors
Facility management companies
Pharmaceutical facility teams
Electronics manufacturing facilities
Laboratories
Testing and commissioning companies
Engineering consultants
Industrial maintenance departments
Why Choose TENMARS TM-4002 for Low Airflow Testing?
The TM-4002 combines several useful characteristics:
Hot wire sensing technology
0.01–25.00 m/s air velocity measurement
400–1020 mm telescopic probe
CFM and CMM air volume measurement
Temperature measurement
Relative humidity measurement
Dew point
Wet bulb temperature
99 sets of manual data memory
For professionals who require relatively low airflow measurement together with HVAC environmental parameters, this combination makes the TM-4002 a practical instrument to consider.
TENMARS TM-4002 Hot Wire Anemometer Malaysia
For cleanroom airflow testing, HVAC inspection, controlled-environment measurement and ventilation applications, the TENMARS TM-4002 provides a useful combination of airflow and environmental measurement functions.
For enquiries regarding the TENMARS TM-4002 Hot Wire Anemometer in Malaysia, contact MTM Precision.
Contact MTM Precision
MTM Precision Sdn. Bhd.
Showroom & Service Centre
No. 29-1 & 29-2, Jalan Bandar 18,
Pusat Bandar Puchong,
47160 Puchong, Selangor, Malaysia
🌐 Website: www.mtmpre.com.my
📧 Email: mtmpre@yahoo.com
📱 WhatsApp: +6016-660 7346
15 Aug 2026