How to Use Linshang LS251D Leeb Hardness Tester Correctly Malaysia

How to Use Linshang LS251D Leeb Hardness Tester Correctly Malaysia

 

Practical Guide for Reliable Portable Hardness Testing

 

The Linshang LS251D Leeb Hardness Tester is designed for portable hardness measurement of suitable metal workpieces, especially large and heavy components that are difficult to move to a conventional bench hardness tester.

 

However, accurate hardness testing depends on more than simply placing the probe against the metal and taking a reading.

 

Workpiece condition, surface preparation, material selection and measurement technique can all influence the result.

 

1. Confirm the Workpiece Is Suitable

 

Before testing, check whether the component is suitable for the Leeb rebound method.

 

Important factors include:

 

Workpiece mass

 

Material thickness

 

Surface roughness

 

Surface curvature

 

Component stability

 

Test location

 

Large, heavy and rigid components are generally the most suitable for Leeb hardness testing.

 

Small or lightweight components may require proper coupling to a rigid supporting body.

 

2. Identify the Material

 

Select the correct material setting before measurement.

 

The LS251D supports applicable metallic materials such as:

 

Steel and cast steel

 

Alloy tool steel

 

Stainless steel

 

Grey cast iron

 

Nodular cast iron

 

Cast aluminium alloy

 

Brass

 

Bronze

 

Pure copper

 

Forged steel

 

Correct material selection is particularly important when the instrument is converting the Leeb result into another hardness scale.

 

3. Prepare the Measurement Surface

 

The test surface should be clean and sufficiently smooth.

 

Remove conditions that may interfere with the impact measurement, such as:

 

Loose rust

 

Heavy oxide scale

 

Dirt

 

Paint or unsuitable coatings

 

Excessive roughness

 

Surface contamination

 

Surface preparation is one of the most important steps in obtaining consistent Leeb hardness readings.

 

4. Select the Required Hardness Scale

 

The LS251D supports multiple hardness scales, including:

 

HL, HV, HB, HS, HRA, HRB and HRC.

 

Select the scale required by your engineering specification or inspection procedure.

 

Remember that values such as HRC, HB and HV displayed by a Leeb tester are converted values where applicable.

 

If a standard specifically requires direct Rockwell, Brinell or Vickers testing, follow the required method.

 

5. Position the Impact Device Correctly

 

Place the D-type impact device firmly against the prepared surface.

 

Avoid:

 

Unstable contact

 

Excessive movement

 

Testing too close to an unsuitable edge

 

Poorly supported areas

 

The LS251D digital impact device provides automatic impact direction recognition and compensation, which is useful when testing surfaces at different orientations.

 

6. Perform the Measurement

 

Load the impact device according to the operating procedure and position it firmly on the selected test location.

 

Trigger the measurement while keeping the probe stable.

 

Avoid moving the probe during the impact.

 

The hardness result will then be displayed by the instrument.

 

7. Never Depend on One Reading

 

Take several measurements around the selected test area.

 

Multiple readings help identify abnormal results caused by:

 

Surface roughness

 

Incorrect positioning

 

Local material variation

 

Workpiece movement

 

Poor preparation

 

A group of reasonably consistent readings is generally more meaningful than a single measurement.

 

8. Check Unexpected Results

 

Suppose the expected hardness is around a certain range, but one reading is significantly different.

 

Do not immediately conclude that the component has failed.

 

Check:

 

Was the surface prepared correctly?

 

Is the material setting correct?

 

Is the workpiece sufficiently heavy?

 

Is the test location too close to an edge?

 

Did the component move?

 

Was the impact device positioned correctly?

 

Correct the possible problem and repeat the measurement.

 

9. Keep the Impact Device Clean

 

The impact device is an important part of the Leeb hardness tester.

 

Keep it clean and protect it from:

 

Dust

 

Metal particles

 

Oil contamination

 

Impact damage

 

Improper storage

 

Good instrument care helps maintain reliable operation.

 

10. Verify the Instrument Regularly

 

Before important inspection work, check the instrument using the appropriate reference hardness block and follow the manufacturer's verification procedure.

 

If readings are consistently outside the acceptable range, investigate the instrument, impact device and testing technique before continuing.

 

Common Mistakes to Avoid

 

Some of the most common mistakes when using a Leeb hardness tester include:

 

Testing very thin material directly

 

Testing lightweight parts without coupling

 

Measuring on rust or scale

 

Selecting the wrong material

 

Using only one reading

 

Testing an unstable workpiece

 

Ignoring surface curvature

 

Treating converted HRC as a direct Rockwell test

 

Ignoring the applicable inspection standard

 

Avoiding these mistakes can significantly improve measurement reliability.

 

Example: Testing a Large Machine Shaft

 

For a large steel shaft:

 

Step 1: Confirm the shaft has sufficient mass and thickness.

 

Step 2: Prepare a smooth measurement area.

 

Step 3: Select the appropriate steel material setting.

 

Step 4: Select the required hardness scale.

 

Step 5: Position the LS251D impact device firmly.

 

Step 6: Take several measurements.

 

Step 7: Compare the results against the applicable engineering requirement.

 

This type of application demonstrates the main advantage of portable Leeb hardness testing: the large component does not need to be transported to a laboratory simply for a hardness check.

 

Reliable Hardness Testing Starts with Correct Technique

 

A good hardness tester cannot compensate for every incorrect testing practice.

 

For reliable results, users must combine:

 

Suitable workpiece + proper surface preparation + correct material setting + correct measurement technique + appropriate interpretation.

 

The Linshang LS251D Leeb Hardness Tester provides a convenient solution for Malaysian factories, engineering workshops, maintenance departments and industrial inspection teams that need portable hardness measurement of suitable metal components.

 

Contact MTM Precision

 

MTM Precision Sdn. Bhd.

Showroom & Service Centre

No. 29-1 & 29-2, Jalan Bandar 18,

Pusat Bandar Puchong,

47160 Puchong, Selangor, Malaysia

 

🌐 Website: www.mtmpre.com.my

📧 Email: mtmpre@yahoo.com

📱 WhatsApp: +6016-660 7346


 

15 Aug 2026