Why Workpiece Weight and Thickness Matter in Leeb Hardness Testing Malaysia
Why Workpiece Weight and Thickness Matter in Leeb Hardness Testing Malaysia
Understanding Linshang LS251D Workpiece Requirements
One of the most common misunderstandings about portable Leeb hardness testers is that they can measure any metal object simply by placing the impact device on the surface.
In reality, workpiece weight and thickness are critical factors.
The Linshang LS251D Leeb Hardness Tester uses the rebound principle. If the workpiece is too light, too thin or insufficiently supported, vibration and movement during impact can affect the hardness reading.
Why Does Workpiece Weight Matter?
During a Leeb hardness test, the impact body strikes the surface of the material.
A large and heavy workpiece remains relatively stable during this impact.
A lightweight component may move or vibrate.
That movement can affect the rebound behaviour measured by the instrument.
This is why portable Leeb hardness testers are particularly suitable for:
Large shafts
Heavy gears
Large moulds
Castings
Forgings
Machine components
Heavy steel parts
Installed machinery
LS251D Minimum Workpiece Weight
For the Linshang LS251D with its D-type impact device, a workpiece of approximately 5 kg or above can generally be measured directly when the other testing requirements are satisfied.
For lighter workpieces, additional support or coupling may be required.
This is an important specification to understand before purchasing a Leeb hardness tester.
Why Does Thickness Matter?
Thickness affects the rigidity of the measurement area.
If a metal component is too thin, the impact may cause:
Flexing
Vibration
Local movement
This can influence the rebound measurement and result in unstable or misleading readings.
For direct measurement using the D-type impact device, the LS251D is intended for workpieces with sufficient thickness.
The manufacturer's guidance specifies approximately 25 mm minimum thickness for direct testing under the applicable conditions.
What If the Workpiece Is Smaller or Thinner?
A smaller workpiece does not automatically mean that Leeb hardness testing is impossible.
In some cases, the workpiece can be firmly coupled to a heavy and rigid supporting body.
With appropriate coupling, thinner workpieces may be tested under the manufacturer's specified conditions, with minimum thickness potentially around 3 mm.
However, correct coupling technique is essential.
Simply placing a thin piece of metal on a table is not the same as properly coupling it to a heavy support.
What Is Coupling?
Coupling means creating firm contact between a lightweight test piece and a much heavier supporting body so that they behave more like one rigid mass during impact.
The surfaces should be suitable for close contact, and the workpiece must not move during measurement.
The purpose is to reduce vibration and movement caused by the impact.
Example: Large Steel Shaft
Consider a 50 kg steel shaft.
The shaft is:
Heavy
Rigid
Thick
Stable
After preparing an appropriate measurement surface, this type of component is generally much more suitable for Leeb hardness testing.
This is one reason the LS251D is useful for heavy engineering applications.
Example: Thin Steel Plate
Now consider a thin steel plate weighing only a few hundred grams.
If the technician simply holds the plate and performs an impact measurement, the plate may vibrate.
The displayed value may look convincing, but that does not necessarily mean the measurement is reliable.
The workpiece may require proper coupling, or another hardness testing method may be more appropriate.
Don't Confuse “Reading” with “Reliable Reading”
This is an important principle.
A portable hardness tester may display a number even when the workpiece conditions are unsuitable.
The presence of a number on the screen does not automatically mean the test is valid.
Users must first confirm:
Workpiece weight
Thickness
Rigidity
Surface condition
Material selection
Testing position
Only then should the result be interpreted.
Other Factors Still Matter
Even when the workpiece is sufficiently heavy and thick, other conditions can affect measurement quality.
These include:
Surface roughness
Rust and scale
Surface curvature
Test location
Material selection
Probe positioning
Distance from edges
Workpiece weight and thickness are important, but they are only part of correct Leeb hardness testing practice.
Why This Matters When Buying a Hardness Tester
Before purchasing the Linshang LS251D, customers should consider the actual components they intend to measure.
Useful information includes:
Material: Steel, stainless steel, cast iron, aluminium alloy, etc.
Weight: Is the component above or below approximately 5 kg?
Thickness: Is it sufficiently thick for direct measurement?
Size: Is it a large machinery component or a small part?
Hardness Scale: HL, HRC, HB, HV or another required scale?
These details can quickly indicate whether a Leeb hardness tester is suitable.
Linshang LS251D for Large Metal Components
The Linshang LS251D Leeb Hardness Tester is especially relevant for large and heavy metal components where portability provides a major advantage.
Typical users in Malaysia may include:
Machine shops
Steel fabricators
Manufacturing factories
Maintenance departments
Heavy equipment companies
Engineering contractors
Industrial inspection teams
For small, lightweight or very thin components, the testing requirement should be evaluated carefully before selecting the instrument.
Contact MTM Precision
MTM Precision Sdn. Bhd.
Showroom & Service Centre
No. 29-1 & 29-2, Jalan Bandar 18,
Pusat Bandar Puchong,
47160 Puchong, Selangor, Malaysia
🌐 Website: www.mtmpre.com.my
📧 Email: mtmpre@yahoo.com
📱 WhatsApp: +6016-660 7346
15 Aug 2026