Common Leeb Hardness Testing Errors and How to Avoid Them Malaysia

Common Leeb Hardness Testing Errors and How to Avoid Them Malaysia

 

Linshang LS251D Troubleshooting Guide for More Reliable Measurements

 

Portable Leeb hardness testers are convenient for checking large metal components, but incorrect testing conditions can produce inconsistent or misleading results.

 

When using the Linshang LS251D Leeb Hardness Tester, understanding common measurement errors is just as important as knowing how to operate the instrument.

 

Below are some of the most common problems encountered during portable hardness testing and how to avoid them.

 

1. Testing a Workpiece That Is Too Light

 

Leeb hardness testing uses an impact and rebound principle.

 

If the workpiece is too light, it may move or vibrate when the impact body strikes the surface.

 

Possible Result

 

Readings may fluctuate significantly even when measurements are taken close together.

 

What to Do

 

Check whether the workpiece has sufficient mass for direct measurement.

 

For lighter components, proper coupling to a heavy and rigid supporting body may be required.

 

2. Testing Material That Is Too Thin

 

Thin materials can flex during impact.

 

Even a small amount of movement can influence the rebound measurement.

 

Possible Result

 

The instrument displays a value, but repeated readings may not be stable or representative.

 

What to Do

 

Confirm that the material meets the applicable thickness requirement.

 

If permitted, use the correct coupling method. For very thin components, consider another hardness testing method.

 

3. Measuring on a Rough Surface

 

Surface roughness is one of the most common causes of inconsistent Leeb hardness readings.

 

Possible Result

 

Results may vary widely between nearby measurement points.

 

What to Do

 

Prepare a sufficiently smooth measurement area according to the applicable testing requirements.

 

Do not simply select the cleanest-looking area if the surface is still too rough.

 

4. Testing Over Rust or Scale

 

Industrial components may have rust, oxide scale or other surface contamination.

 

These layers are not necessarily representative of the underlying base material.

 

What to Do

 

Prepare the actual metal surface before testing where required and permitted.

 

Avoid taking measurements directly on loose rust or heavy scale.

 

5. Testing Through Paint or Coating

 

A Leeb hardness tester is intended to evaluate the hardness of the underlying suitable metallic material.

 

Paint and other coatings can interfere with impact behaviour.

 

What to Do

 

Use a properly prepared test area where the base metal can be measured according to the required procedure.

 

Do not assume that the LS251D can simply measure through every coating.

 

6. Selecting the Wrong Material

 

This mistake is especially important when using converted hardness scales.

 

The LS251D supports different metallic materials, and the conversion relationship depends on the selected material.

 

Possible Result

 

The HL measurement may be converted into an inappropriate HRC, HB or HV value.

 

What to Do

 

Confirm the actual material before selecting the corresponding setting.

 

If the material is unknown, hardness testing alone may not be sufficient to identify it.

 

7. Relying on Only One Reading

 

One impact should not normally be used to represent an entire component.

 

Local surface conditions can affect an individual measurement.

 

What to Do

 

Take multiple readings at suitable positions.

 

Look for consistency rather than focusing on one number.

 

8. Measuring Too Close to an Edge

 

The area near an edge may not provide the same support as the main body of the component.

 

Possible Result

 

Readings can become less consistent.

 

What to Do

 

Select a test location that meets the applicable distance and geometry requirements.

 

9. Ignoring Surface Curvature

 

Large shafts, pipes and other cylindrical components have curved surfaces.

 

If the curvature is significant, the impact device may not sit correctly.

 

What to Do

 

Evaluate the radius of curvature and use the appropriate support arrangement or accessories where required.

 

For very small diameters, another testing method may be more appropriate.

 

10. Allowing the Workpiece to Move

 

Even a sufficiently heavy component can sometimes be unstable.

 

For example, a loose component resting on an uneven surface may shift during impact.

 

What to Do

 

Make sure the workpiece is stable before measurement.

 

Do not hold lightweight components by hand while testing.

 

11. Incorrect Impact Device Positioning

 

The impact device should be positioned firmly and consistently against the test surface.

 

Tilting or moving the probe during impact can affect measurement quality.

 

The LS251D provides automatic impact direction recognition and compensation, but the probe still needs proper physical contact with the workpiece.

 

12. Confusing Converted HRC with Direct Rockwell Testing

 

The LS251D can display HRC.

 

However, the instrument performs a Leeb rebound test and converts the result into an equivalent HRC value where applicable.

 

It is not physically performing a conventional Rockwell indentation test.

 

Why This Matters

 

If an engineering specification specifically requires direct Rockwell testing, a converted Leeb value may not satisfy the requirement.

 

Always check the applicable standard or inspection procedure.

 

13. Ignoring Abnormal Readings

 

Suppose five measurements are:

 

42 HRC – 43 HRC – 42 HRC – 57 HRC – 43 HRC

 

The 57 HRC result should not automatically be accepted or averaged without investigation.

 

Check the measurement location, surface and probe positioning, then repeat the test.

 

An abnormal result may indicate either a real material difference or a measurement problem.

 

14. Poor Impact Device Maintenance

 

Dust, contamination or damage to the impact device can affect operation.

 

What to Do

 

Keep the impact device clean and store the instrument properly after use.

 

Follow the manufacturer's maintenance instructions and avoid unnecessary disassembly.

 

15. Not Checking the Instrument Before Important Measurements

 

For important QC or inspection work, instrument verification should be part of good measurement practice.

 

Use the appropriate reference hardness block and follow the recommended verification procedure.

 

If the readings are consistently outside the expected range, investigate before testing production components.

 

Quick Troubleshooting Checklist

 

If LS251D readings are inconsistent, check:

 

Is the workpiece heavy enough?

 

Is the material thick enough?

 

Is the component stable?

 

Is the surface smooth and clean?

 

Is the correct material selected?

 

Is the test location suitable?

 

Is curvature affecting probe contact?

 

Are multiple readings being taken?

 

Is the impact device clean?

 

Has the instrument been verified?

 

These checks can solve many common Leeb hardness testing problems.

 

Reliable Results Depend on the Entire Testing Process

 

The Linshang LS251D Leeb Hardness Tester can provide convenient portable hardness measurement for suitable metal components.

 

However, reliable testing depends on more than the instrument itself.

 

Correct workpiece + correct surface + correct material setting + correct technique = more reliable hardness results.

 

For Malaysian engineering workshops, factories and maintenance departments, understanding these testing fundamentals can help users get much more value from a portable hardness tester.

 

Contact MTM Precision

 

MTM Precision Sdn. Bhd.

Showroom & Service Centre

No. 29-1 & 29-2, Jalan Bandar 18,

Pusat Bandar Puchong,

47160 Puchong, Selangor, Malaysia

 

🌐 Website: www.mtmpre.com.my

📧 Email: mtmpre@yahoo.com

📱 WhatsApp: +6016-660 7346


 

15 Aug 2026