Hot Mix Asphalt Temperature Monitoring Before Compaction with Myzox AST-10 Malaysia

Hot Mix Asphalt Temperature Monitoring Before Compaction with Myzox AST-10 Malaysia

 

Temperature monitoring before asphalt compaction is an important part of road paving and pavement quality control. After hot mix asphalt is placed, it begins to cool continuously, while contractors need to carry out rolling and compaction according to the requirements of the asphalt mix and project specification.

 

The Myzox AST-10 Digital Asphalt Thermometer provides road contractors, site engineers and QA/QC personnel with a practical way to measure asphalt temperature during paving operations.

 

With the Myzox SE-IN 200 mm needle probe, temperature can be measured by direct penetration into the asphalt material.

 

Why Check Asphalt Temperature Before Compaction?

 

Fresh asphalt must remain in a suitable condition for compaction.

 

As the material cools, its characteristics change. Contractors therefore need to coordinate paving and rolling operations according to the approved construction procedure.

 

Temperature measurements can provide useful information when managing this process.

 

Instead of relying only on the amount of time that has passed since paving, the site team can obtain an actual temperature reading.

 

What Can Affect Asphalt Cooling?

 

Hot mix asphalt starts losing heat from the time it leaves the production process.

 

The rate of cooling on site can be affected by many factors, including:

 

Ambient temperature

 

Wind speed

 

Rain and moisture

 

Asphalt layer thickness

 

Existing pavement temperature

 

Transportation time

 

Waiting time

 

Paving speed

 

Compaction sequence

 

Because site conditions can change, actual temperature measurement can be more informative than estimating temperature based only on time.

 

Measuring Temperature Within the Asphalt

 

One important consideration is whether the contractor needs to know surface temperature or temperature within the asphalt.

 

The exposed pavement surface can cool differently from the material underneath.

 

The Myzox SE-IN Needle Probe is designed for penetration measurement.

 

Its specifications include:

 

Probe length: 200 mm

Measurement range: -50掳C to +650掳C

 

Myzox identifies the SE-IN as suitable for asphalt measurement.

 

This allows the probe to be inserted into the material at an appropriate measurement position.

 

How to Use Myzox AST-10 Before Compaction

 

The exact procedure should always follow the project's approved method statement and QA/QC requirements.

 

A typical field measurement may involve:

 

Connect the SE-IN Type-K thermocouple probe to the AST-10.

 

Check that the thermometer is operating correctly.

 

Select an appropriate measurement location.

 

Insert the needle probe into the asphalt.

 

Allow the displayed temperature to stabilize.

 

Record the reading.

 

Repeat measurements where required.

 

Measurements can then be considered together with the project's specified temperature requirements.

 

Do Not Rely on Only One Measurement

 

A road section can cover a large area, and asphalt temperature may not be uniform throughout the entire paving operation.

 

For example, temperature may vary between:

 

Different truck loads

 

Different sections behind the paver

 

Edges and central areas

 

Earlier and later paving locations

 

Different compaction stages

 

Where required, taking multiple measurements provides more information than relying on a single reading.

 

Using Data Hold During Field Measurements

 

The AST-10 includes a Data Hold function.

 

After taking a temperature reading, the technician can retain the displayed value for easier viewing or recording.

 

This is particularly useful on active construction sites where the measurement position may not be convenient for writing down the result immediately.

 

MAX and MIN Temperature Functions

 

The instrument also provides MAX and MIN measurement functions.

 

These allow users to view maximum and minimum temperature values recorded during measurement.

 

For technicians performing repeated checks, this provides additional information about temperature variation.

 

Type-K Thermocouple Measurement

 

The AST-10 main instrument supports Type-K thermocouple measurements from:

 

-200掳C to +1,370掳C

 

However, contractors should remember that each probe has its own measurement range.

 

For the supplied SE-IN asphalt needle probe, the relevant range is:

 

-50掳C to +650掳C

 

Always use the instrument and probe within their specified operating limits.

 

When Should Temperature Be Checked?

 

Depending on the road project's requirements, asphalt temperature may be checked at several stages.

 

When Asphalt Arrives

 

A measurement can be taken after the hot mix asphalt reaches the project site.

 

During Paving

 

Additional readings can be obtained while asphalt is being placed.

 

Before Rolling

 

Temperature can be checked before compaction begins.

 

During Compaction

 

Further measurements may be taken as rolling progresses and the pavement continues to cool.

 

This creates a clearer picture of temperature changes during the paving operation.

 

Does AST-10 Tell the Contractor When to Start Rolling?

 

No.

 

The Myzox AST-10 is a temperature measurement instrument.

 

It provides an actual temperature reading but does not determine the required compaction temperature.

 

The correct rolling temperature depends on the asphalt mix, construction procedure and project specification.

 

The site engineer or responsible QA/QC personnel should interpret the measurement according to the applicable requirements.

 

Why Is This Important for Malaysian Road Projects?

 

Malaysia's road construction environment can include changing weather conditions, high ambient temperatures and sudden rain.

 

Transportation distances and site delays can also vary between projects.

 

Actual temperature measurements help contractors understand the asphalt condition under the specific circumstances occurring at the construction site.

 

Applications Beyond New Road Construction

 

Compaction temperature monitoring is relevant to more than new highways.

 

The Myzox AST-10 can also be used during:

 

Road resurfacing

 

Pavement rehabilitation

 

Asphalt overlay

 

Road widening

 

Pothole repair

 

Car park resurfacing

 

Industrial road construction

 

Access road maintenance

 

Any operation involving hot asphalt placement and compaction may benefit from temperature monitoring.

 

FAQ: What Temperature Should Asphalt Be Compacted At?

 

There is no single temperature that should automatically be applied to every asphalt project.

 

The appropriate temperature depends on factors such as asphalt mix design, material characteristics and project requirements.

 

Always refer to the approved project specification and method statement.

 

The AST-10 provides the temperature measurement needed to compare actual site conditions against those requirements.

 

FAQ: Can an Infrared Thermometer Be Used Before Compaction?

 

An infrared thermometer can provide a surface temperature reading.

 

The AST-10 with SE-IN penetration probe measures temperature within the asphalt material.

 

The appropriate measurement method depends on the project's requirements.

 

FAQ: Why Use a 200 mm Probe?

 

The SE-IN's 200 mm length provides useful reach for penetration measurements.

 

It allows the sensor to make contact with asphalt below the immediate exposed surface, subject to the appropriate measurement procedure.

 

FAQ: Is Myzox AST-10 Suitable for Asphalt QA/QC?

 

Yes.

 

The AST-10 is designed for pavement temperature control and its SE-IN needle probe is suitable for asphalt measurement.

 

It can therefore be incorporated into asphalt temperature inspection and QA/QC procedures where appropriate.

 

Better Temperature Monitoring During Asphalt Compaction

 

Effective road paving requires coordination between asphalt delivery, placement and rolling.

 

Temperature measurement gives contractors additional information for managing this process.

 

The Myzox AST-10 Digital Asphalt Thermometer with SE-IN 200 mm penetration probe provides a portable solution for checking hot mix asphalt temperature before and during compaction.

 

For highway contractors, road construction companies and civil engineering teams in Malaysia, it is a practical instrument for routine pavement temperature control.

 

Myzox Authorized Distributor in Malaysia

 

MTM Precision Sdn. Bhd. is a Myzox Authorized Distributor in Malaysia, supplying Myzox instruments for surveying, civil engineering, highway construction and road maintenance.

 

Contact MTM Precision for information, quotation and availability of the Myzox AST-10 Digital Asphalt Thermometer in Malaysia.

 

Contact MTM Precision

 

MTM Precision Sdn. Bhd.

Showroom & Service Centre

No. 29-1 & 29-2, Jalan Bandar 18,

Pusat Bandar Puchong,

47160 Puchong, Selangor, Malaysia.

 

Website: www.mtmpre.com.my

Email: mtmpre@yahoo.com

WhatsApp: +6016-6607346

 

Contact us for Myzox AST-10 Digital Asphalt Thermometer Malaysia, hot mix asphalt temperature measurement and road construction equipment.


 

16 Aug 2026