How to Check Hot Mix Asphalt Delivery Temperature with Myzox AST-10 Malaysia

How to Check Hot Mix Asphalt Delivery Temperature with Myzox AST-10 Malaysia

 

Hot mix asphalt can begin losing heat during transportation from the asphalt plant to the road construction site. For this reason, checking asphalt temperature at delivery can be an important part of pavement construction and QA/QC procedures.

 

The Myzox AST-10 Digital Asphalt Thermometer provides road contractors, site engineers and quality-control personnel with a practical method for measuring asphalt temperature when material arrives at site.

 

With the Myzox SE-IN 200 mm needle probe, contractors can perform direct penetration temperature measurements within the asphalt material.

 

Why Check Asphalt Temperature When It Arrives?

 

Asphalt may travel a considerable distance between the production plant and the construction site.

 

During transportation, the material is affected by factors such as:

 

Travel distance

 

Travel time

 

Traffic delays

 

Truck waiting time

 

Ambient temperature

 

Wind

 

Rain

 

Load condition

 

By checking temperature when the asphalt arrives, the site team obtains an actual measurement of the material condition at that point in the construction process.

 

Where Does Temperature Monitoring Fit into Asphalt Paving?

 

Temperature monitoring can take place at several stages:

 

Asphalt Plant → Transportation → Site Delivery → Paving → Compaction

 

Delivery temperature measurement sits between production and actual pavement placement.

 

It provides information that can be recorded before the material proceeds further into the paving operation.

 

Myzox AST-10 for Asphalt Delivery Inspection

 

The Myzox AST-10 is designed for pavement temperature control.

 

It uses Type-K thermocouple probes and supports a main instrument measurement range of:

 

-200°C to +1,370°C

 

The actual usable range depends on the probe connected.

 

For hot mix asphalt, the SE-IN Needle Probe is particularly relevant.

 

200 mm Penetration Probe for Hot Asphalt

 

The Myzox SE-IN provides:

 

200 mm probe length

 

-50°C to +650°C measurement range

 

Type-K thermocouple measurement

 

Penetration-type design

 

Suitability for asphalt measurement

 

Instead of measuring only the outside surface of the material, the probe can be inserted into the asphalt at an appropriate measurement point.

 

How to Check Asphalt Delivery Temperature

 

The exact inspection procedure should always follow the project's approved QA/QC plan and safety requirements.

 

A typical measurement process may include the following steps.

 

Step 1: Prepare the AST-10

 

Connect the SE-IN Type-K thermocouple probe securely to the AST-10.

 

Check that the instrument is operating normally before beginning the inspection.

 

Step 2: Identify the Asphalt Load

 

Before taking a reading, record the relevant truck, batch or delivery information according to the project's documentation procedure.

 

This makes it possible to associate the temperature reading with the correct asphalt delivery.

 

Step 3: Select an Appropriate Measurement Point

 

Choose a suitable and safe measurement location according to the approved inspection method.

 

The measurement point should be selected to provide useful information about the asphalt being inspected.

 

Step 4: Insert the Probe

 

Carefully insert the SE-IN needle probe into the asphalt according to the required measurement procedure.

 

The penetration probe allows temperature to be measured within the material.

 

Step 5: Wait for the Reading to Stabilize

 

Allow the displayed temperature to stabilize before recording the result.

 

Removing the probe too quickly can reduce the usefulness of the measurement.

 

Step 6: Use Data Hold if Required

 

The AST-10 provides a Data Hold function.

 

This allows the displayed reading to be retained, which can make it easier to record the measurement after removing the probe.

 

Step 7: Record the Result

 

Record the temperature together with the relevant delivery information.

 

Depending on the project, this may include:

 

Date

 

Time

 

Truck number

 

Asphalt batch

 

Mix identification

 

Delivery location

 

Temperature

 

Weather condition

 

Inspector

 

Remarks

 

Should Every Asphalt Truck Be Checked?

 

The required inspection frequency depends on the project's specification and QA/QC procedure.

 

Some projects may require more frequent measurements than others.

 

The AST-10 provides the measurement capability, while the number of loads or locations to be tested should be determined by the applicable project requirements.

 

Why Not Judge Asphalt Temperature by Appearance?

 

Visual inspection is useful for many aspects of construction, but it cannot provide an exact numerical temperature.

 

Two asphalt loads may appear similar while having different temperatures.

 

Using a digital asphalt thermometer gives the contractor a measurable value that can be recorded.

 

Why Not Rely Only on Travel Time?

 

Travel time can indicate how long the asphalt has been away from the plant, but it does not directly tell the contractor its current temperature.

 

Two deliveries with similar travel times may experience different conditions because of:

 

Traffic

 

Weather

 

Truck condition

 

Waiting time

 

Initial material temperature

 

Direct measurement provides information about the actual temperature at the time of inspection.

 

Penetration Measurement vs Surface Measurement

 

This distinction is important during asphalt delivery inspection.

 

An infrared thermometer generally measures the exposed surface.

 

The AST-10 with SE-IN probe measures temperature by direct contact within the asphalt.

 

Because the surface and internal material may cool differently, these two measurement methods should not automatically be considered interchangeable.

 

Can AST-10 Also Measure Surface Temperature?

 

Yes, when paired with the optional Myzox SE-SU Surface Probe.

 

The SE-SU has a measurement range of:

 

-20°C to +400°C

 

This allows the AST-10 platform to support contact surface measurements in addition to penetration measurements.

 

What Happens if the Asphalt Temperature Is Outside the Project Requirement?

 

The AST-10 only provides the temperature measurement.

 

It does not determine whether a load should be accepted or rejected.

 

Any acceptance decision should follow:

 

Project specifications

 

Approved method statements

 

Asphalt mix requirements

 

QA/QC procedures

 

Instructions from the responsible project personnel

 

The instrument provides objective temperature data to support this process.

 

MAX and MIN Measurement Functions

 

In addition to Data Hold, the AST-10 includes:

 

MAX measurement

 

MIN measurement

 

Relative measurement mode

 

These functions can be useful when performing repeated temperature checks during delivery and paving operations.

 

Who Can Use AST-10 for Asphalt Delivery Inspection?

 

Potential users include:

 

Road contractors

 

Highway contractors

 

Asphalt paving companies

 

Civil engineering contractors

 

QA/QC engineers

 

Site engineers

 

Construction consultants

 

Site supervisors

 

Field technicians

 

Road maintenance teams

 

FAQ: Can Myzox AST-10 Measure Hot Mix Asphalt in a Truck?

 

The AST-10 with SE-IN needle probe is suitable for asphalt penetration temperature measurement.

 

The actual measurement location and procedure should follow the project's approved safety and QA/QC requirements.

 

Personnel should never enter unsafe positions or approach operating equipment contrary to site safety procedures simply to obtain a temperature reading.

 

FAQ: What Is the SE-IN Probe Temperature Range?

 

The Myzox SE-IN needle probe has a specified measurement range of:

 

-50°C to +650°C

 

It is approximately 200 mm long and is suitable for asphalt measurement.

 

FAQ: Does AST-10 Record the Asphalt Batch Number?

 

No.

 

The AST-10 measures temperature.

 

Batch, truck, location and other QA/QC information should be recorded separately according to the project's documentation system.

 

FAQ: Can the Same AST-10 Be Used Later During Paving?

 

Yes.

 

The AST-10 can also be used for temperature checking during asphalt placement, before compaction and during other stages of road construction where appropriate.

 

This allows one portable thermometer to support multiple temperature inspection points throughout the paving process.

 

Digital Asphalt Thermometer for Asphalt Delivery Malaysia

 

Checking hot mix asphalt temperature when it arrives at site provides contractors with useful information before paving begins.

 

The Myzox AST-10 Digital Asphalt Thermometer with SE-IN 200 mm needle probe offers a practical penetration measurement solution for this application.

 

From asphalt delivery through paving and compaction, the AST-10 can support temperature monitoring throughout the road construction workflow.

 

Myzox Authorized Distributor in Malaysia

 

MTM Precision Sdn. Bhd. is a Myzox Authorized Distributor in Malaysia, supplying Myzox surveying, civil engineering and road construction equipment.

 

Contact MTM Precision for product information, quotation and availability of the Myzox AST-10 Digital Asphalt Thermometer in Malaysia.

 

Contact MTM Precision

 

MTM Precision Sdn. Bhd.

Showroom & Service Centre

No. 29-1 & 29-2, Jalan Bandar 18,

Pusat Bandar Puchong,

47160 Puchong, Selangor, Malaysia.

 

Website: www.mtmpre.com.my

Email: mtmpre@yahoo.com

WhatsApp: +6016-6607346

 

Contact us for Myzox AST-10 Digital Asphalt Thermometer Malaysia, hot mix asphalt temperature measurement, asphalt QA/QC and road construction equipment.


 

16 Aug 2026