Asphalt Compaction Temperature Problems and Troubleshooting with Myzox AST-10 Malaysia
Asphalt Compaction Temperature Problems and Troubleshooting with Myzox AST-10 Malaysia
Temperature is one of the important conditions that road contractors monitor during asphalt paving and compaction. Once hot mix asphalt is placed, it continues losing heat, while the paving team must complete rolling according to the applicable project and asphalt mix requirements.
When temperature readings appear inconsistent or asphalt cools differently from expected, contractors need to determine whether the issue comes from the material, site conditions, measurement method or equipment.
The Myzox AST-10 Digital Asphalt Thermometer with SE-IN 200 mm needle probe provides a practical method for checking penetration temperature during asphalt paving and compaction in Malaysia.
Problem 1: Asphalt Temperature Drops Faster Than Expected
One common concern is asphalt cooling more quickly than anticipated after paving.
Possible contributing factors can include:
Wind
Ambient conditions
Rain or moisture
Thin asphalt layers
Existing pavement temperature
Delays in paving
Delays before rolling
Rather than estimating the asphalt temperature from elapsed time, contractors can take actual measurements at appropriate locations.
The AST-10 provides a numerical temperature reading that can be compared with the project's requirements.
Problem 2: Different Areas Show Different Temperatures
Temperature may not be uniform across an entire paving area.
One road section may show a different reading from another because of:
Different placement times
Different truck loads
Local cooling conditions
Layer thickness variation
Wind exposure
Paving sequence
Where the QA/QC procedure requires it, take multiple measurements and record the location of each reading.
A single temperature should not automatically be assumed to represent the entire paving area.
Problem 3: Surface Temperature Is Different from Probe Temperature
This does not necessarily mean that one instrument is faulty.
An infrared thermometer generally measures exposed surface temperature.
The Myzox AST-10 with SE-IN probe measures temperature by penetration into the asphalt.
Surface and internal asphalt can cool differently.
Therefore, readings obtained using these two methods should not automatically be expected to match.
Problem 4: Temperature Reading Keeps Changing
If the AST-10 display changes after the probe is inserted, the sensor may still be responding to the asphalt temperature.
Allow sufficient time for the reading to stabilize before recording it.
Removing the probe immediately after insertion can produce an inconsistent measurement procedure.
Problem 5: Reading Looks Unrealistic
If the displayed temperature appears unreasonable, check the measurement setup.
Possible items to inspect include:
Probe connection
Probe condition
Thermocouple cable
Battery condition
Instrument display
Measurement position
Probe temperature range
Repeat the measurement at an appropriate location after checking the equipment.
If the problem continues, the instrument or probe may require further inspection.
Problem 6: Wrong Probe Is Being Used
The AST-10 supports different Type-K thermocouple probes.
For asphalt penetration measurement, the SE-IN Needle Probe is particularly relevant.
Its specifications include:
Probe length: 200 mm
Measurement range: -50掳C to +650掳C
Myzox identifies this probe as suitable for asphalt measurement.
Other probes should be selected according to their intended application and specified temperature range.
Problem 7: Main Instrument Range Is Confused with Probe Range
The Myzox AST-10 main instrument supports Type-K thermocouple measurements from:
-200掳C to +1,370掳C
However, this does not mean the SE-IN probe can be used across that entire range.
The SE-IN range is:
-50掳C to +650掳C
Always consider the temperature rating of the connected probe.
Problem 8: Asphalt Has Cooled During Transportation
Sometimes the issue begins before the material reaches the paver.
Hot mix asphalt can lose heat during transportation because of:
Long delivery distance
Traffic congestion
Waiting time
Weather
Site access delays
Operational interruptions
Temperature measurement at delivery can help the QA/QC team understand the material condition before paving begins.
Problem 9: Paving Has Been Delayed
Construction delays can occur because of:
Equipment issues
Traffic management
Weather
Site coordination
Paver interruptions
During a delay, asphalt continues exchanging heat with the environment.
When work resumes, an actual temperature measurement can provide more useful information than assuming the material remains at its previous temperature.
Problem 10: Rolling Is Delayed
If compaction does not begin as planned, the asphalt may continue cooling.
The AST-10 can be used to obtain a penetration temperature measurement before rolling where required.
The responsible project personnel should then assess the reading according to the applicable project requirements.
Problem 11: Temperature Varies Between Truck Loads
Different deliveries can arrive under different conditions.
For example, two trucks may experience different:
Travel times
Traffic conditions
Waiting periods
Weather exposure
Recording temperature together with truck or batch identification helps distinguish individual deliveries.
Problem 12: Temperature Records Cannot Be Traced
A number without context has limited QA/QC value.
Instead of recording only:
Temperature: ___掳C
consider recording:
Date
Time
Truck or batch
Road section
Chainage
Measurement stage
Measurement location
Temperature
Weather
Inspector
This makes the measurement easier to review later.
How Myzox AST-10 Helps Troubleshooting
The AST-10 provides several useful functions for field temperature measurement.
Data Hold
Retains the displayed temperature for easier reading and recording.
MAX and MIN
Allows maximum and minimum values to be viewed during measurement.
Relative Measurement
Provides additional flexibility when comparing temperature readings.
Interchangeable Type-K Probes
Different probes can be selected for different contact temperature measurement requirements.
Can AST-10 Measure Surface Temperature?
Yes, with the optional Myzox SE-SU Surface Probe.
The SE-SU has a measurement range of:
-20掳C to +400掳C
This provides contact surface measurement.
For penetration measurement inside asphalt, the SE-IN needle probe is the appropriate option.
What Should You Do When a Temperature Is Outside the Required Range?
Do not make an acceptance decision based solely on a generic temperature value found online.
The appropriate response should follow:
Project specifications
Asphalt mix requirements
Approved method statement
QA/QC procedures
Instructions from responsible engineering personnel
The AST-10 measures the actual temperature; it does not determine whether the pavement passes or fails.
FAQ: Why Does Asphalt Temperature Change So Quickly?
Hot asphalt continuously transfers heat to its surroundings.
Cooling can be influenced by environmental conditions, layer thickness, pavement conditions and construction timing.
Actual cooling behaviour therefore varies between projects.
FAQ: Why Are My Infrared and Probe Readings Different?
They measure different locations.
An infrared thermometer generally measures the surface, while the SE-IN penetration probe measures within the asphalt.
A difference between readings is therefore possible.
FAQ: Should I Take More Than One Reading?
Where required by the project procedure, multiple readings at appropriate locations can provide more information than a single measurement.
Always record where and when the measurement was taken.
FAQ: Can AST-10 Solve Asphalt Compaction Problems?
The AST-10 does not solve compaction problems by itself.
It provides temperature data that helps engineers and contractors understand actual site conditions.
That information can support troubleshooting and construction decisions.
Troubleshooting Asphalt Temperature with Actual Measurements
When asphalt paving conditions do not develop as expected, guessing the temperature is not an effective troubleshooting method.
Actual measurements provide useful evidence.
The Myzox AST-10 Digital Asphalt Thermometer with SE-IN 200 mm needle probe allows Malaysian road contractors to perform penetration temperature checks during delivery, paving and compaction.
Combined with consistent measurement procedures and proper QA/QC records, it can be a valuable tool for investigating asphalt temperature variations on site.
Myzox Authorized Distributor in Malaysia
MTM Precision Sdn. Bhd. is a Myzox Authorized Distributor in Malaysia, supplying Myzox equipment for surveying, civil engineering, road construction and pavement measurement applications.
Contact MTM Precision for information, quotation and availability of the Myzox AST-10 Digital Asphalt Thermometer in Malaysia.
Contact MTM Precision
MTM Precision Sdn. Bhd.
Showroom & Service Centre
No. 29-1 & 29-2, Jalan Bandar 18,
Pusat Bandar Puchong,
47160 Puchong, Selangor, Malaysia.
Website: www.mtmpre.com.my
Email: mtmpre@yahoo.com
WhatsApp: +6016-6607346
Contact us for Myzox AST-10 Digital Asphalt Thermometer Malaysia, asphalt compaction temperature measurement, troubleshooting and road construction QA/QC equipment.
16 Aug 2026