Rotating Equipment Preventive Maintenance Checklist Using a Vibration Meter Malaysia
Rotating equipment is essential to almost every factory.
Electric motors drive pumps, fans, compressors, gearboxes, conveyors and production machinery. When one critical machine fails unexpectedly, the result may be production downtime, emergency repair and higher maintenance costs.
A practical preventive maintenance programme should therefore look beyond simply replacing parts according to a calendar.
By adding vibration measurement to routine inspections, maintenance engineers can monitor how machine condition changes over time.
This guide provides a practical rotating equipment preventive maintenance checklist for factories and maintenance teams in Malaysia.
Which Rotating Equipment Should Be Included?
Typical equipment includes:
Electric motors
Pumps
Fans
Blowers
Compressors
Gearboxes
Generators
Cooling tower fans
AHU fans
Conveyors
Production machinery
Start with machines whose failure would have the greatest operational impact.
1. Visual Inspection
Before taking measurements, look at the machine.
Check for:
Loose bolts
Oil leakage
Grease leakage
Damaged guards
Cracked mounting
Corrosion
Damaged belts
Unusual movement
Contamination
Missing components
Simple visual inspection can reveal problems that vibration measurement alone cannot identify.
2. Listen for Abnormal Noise
Listen for changes such as:
Grinding
Rattling
Rumbling
Squealing
Repetitive knocking
Unusual mechanical noise
Do not rely only on hearing.
Use noise as one condition indicator and combine it with vibration and other inspection information.
3. Check Machine Vibration
Use a portable vibration meter at established measurement points.
Depending on the instrument, you may measure:
Velocity → Acceleration → Displacement
For general rotating machinery condition monitoring, vibration velocity in mm/s is commonly used.
Record the measurement instead of relying on comments such as:
“Machine vibration seems okay.”
4. Use Fixed Measurement Points
Consistency is essential.
For an electric motor, points may include:
Drive End — DE
Non-Drive End — NDE
For a motor-driven pump:
Motor NDE → Motor DE → Pump DE → Pump NDE
Use the same locations during future inspections whenever practical.
5. Check Horizontal, Vertical and Axial Vibration
Depending on the machine and monitoring programme, vibration may be measured in:
Horizontal
Vertical
Axial
Create measurement point codes such as:
M01-DE-H
Motor 01 → Drive End → Horizontal
This makes historical data easier to compare.
6. Check Bearing Condition
Bearings are critical components in rotating equipment.
Look for:
Increased vibration
Increased temperature
Abnormal noise
Lubrication problems
Loose bearing housings
Remember:
High vibration near a bearing does not automatically mean bearing failure.
The vibration may originate elsewhere.
7. Check Lubrication
Inspect lubrication according to equipment requirements.
Possible issues include:
Insufficient lubrication
Excessive lubrication
Incorrect lubricant
Contamination
Leakage
Deteriorated lubricant
Lubrication condition can influence bearing and gearbox reliability.
8. Check Alignment
For coupled machinery such as:
Motor → Pump
or:
Motor → Gearbox
shaft alignment is important.
Possible signs of alignment-related problems may include:
Increased vibration
Coupling wear
Bearing problems
Seal problems
If vibration increases after motor, pump or coupling work, alignment should be included in the investigation.
9. Check Mechanical Looseness
Inspect:
Mounting bolts
Motor feet
Pump mounting
Bearing housings
Base plates
Foundations
Guards
Frames
Looseness can produce or amplify machine vibration.
Sometimes a high vibration problem can be related to the installation rather than an expensive internal component.
10. Check for Imbalance
Rotating components can become unbalanced because of:
Dust
Dirt
Deposits
Corrosion
Damage
Uneven wear
Fans and blowers are common examples.
A dirty fan wheel may develop increasing vibration even though its bearings are still functional.
11. Check Belts and Pulleys
For belt-driven equipment, inspect:
Belt condition
Belt tension
Cracks
Wear
Pulley condition
Pulley alignment
The entire drive system should be considered:
Motor → Pulley → Belt → Driven Pulley → Machine
12. Check Couplings
Couplings transmit power between rotating shafts.
Inspect for:
Wear
Damage
Loose components
Alignment issues
A coupling problem can affect vibration at both the driving and driven machine.
13. Check Bearing Temperature
Temperature measurement complements vibration monitoring.
Maintenance teams can use:
Vibration Meter + Infrared Thermometer
or:
Vibration Meter + Thermal Imager
to check machine condition.
Increasing vibration together with increasing bearing temperature may justify further investigation.
14. Record Machine Speed
RPM can significantly affect vibration behaviour.
Record speed where practical.
This is particularly important for:
Variable-speed motors
VFD-controlled equipment
Fans
Pumps
Production machinery
Comparing measurements taken at very different speeds can be misleading.
15. Record Operating Load
Machine vibration may change according to operating condition.
Record information such as:
Production load
Pump flow
Pressure
Compressor load
Generator load
For useful trending, compare readings taken under reasonably similar operating conditions.
16. Compare with Baseline Vibration
A baseline is the vibration level recorded while the machine is operating normally.
Example:
Motor 02 DE-H Baseline = 1.6 mm/s
Later:
1.7 → 1.8 → 2.2 → 2.9 → 3.7 mm/s
The increasing trend provides useful maintenance information.
17. Review the Trend
Do not look only at today's reading.
Ask:
What was the reading last month?
What was it six months ago?
A gradually increasing trend may provide an early indication of changing machine condition.
This is one of the biggest advantages of routine vibration monitoring.
18. Investigate Sudden Changes
Suppose vibration changes from:
1.8 mm/s
to:
4.5 mm/s
First confirm:
Correct measurement point
Correct vibration parameter
Good sensor contact
Similar RPM
Similar operating condition
If the high reading is confirmed, investigate the machine.
19. Check the Driven Equipment
Do not inspect only the motor.
For example:
Motor → Coupling → Pump
The vibration source could be:
Motor
Coupling
Pump
Foundation
Connected piping
Measure across the complete machine train where appropriate.
20. Record Maintenance Actions
When corrective work is performed, record it.
For example:
Date: 20 August
Machine: Exhaust Fan 02
Problem: High vibration
Action: Fan cleaned and mounting corrected
Then take another vibration measurement.
Measure Before and After Maintenance
This is one of the most useful vibration maintenance practices.
Example:
Before maintenance:
4.6 mm/s
After maintenance:
2.1 mm/s
Now you have numerical evidence showing whether the corrective work improved machine behaviour.
Example Preventive Maintenance Record
A simple record can contain:
Machine: Cooling Water Pump 01
Measurement Point: Pump DE Horizontal
Velocity: 2.2 mm/s
RPM: 1450
Bearing Temperature: Normal
Noise: Normal
Lubrication: Checked
Mounting: Checked
Remarks: No significant change
This creates a much more useful equipment history than simply marking:
“PM Completed.”
Preventive Maintenance vs Condition-Based Maintenance
Traditional preventive maintenance may say:
Replace Bearing Every X Months
Condition monitoring adds another question:
What is the actual machine condition?
The two approaches can work together.
A factory may continue scheduled maintenance while using vibration trends to improve maintenance decisions.
What Can a Vibration Meter Detect?
A portable vibration meter can help identify changing machine behaviour associated with conditions such as:
Imbalance
Misalignment
Bearing deterioration
Mechanical looseness
Pump problems
Fan problems
Gearbox problems
However, an overall vibration reading does not automatically identify the exact fault.
Further inspection or advanced vibration analysis may be required.
Vibration Meter vs Vibration Analyzer
For routine preventive maintenance:
Portable Vibration Meter
is useful for:
Screening
Baseline measurements
Trending
Routine routes
For deeper diagnostics:
Vibration Analyzer
may be required for frequency spectrum and advanced fault analysis.
Many factories can begin with portable vibration measurements and escalate abnormal machines for deeper investigation.
Vibration Meter Options from MTM Precision Malaysia
MTM Precision supplies vibration measurement instruments for preventive maintenance and machine condition monitoring applications.
Showa Sokki SH-1332B
Suitable for professional industrial vibration measurement and maintenance work.
Landtek VM6310 / VM6360 / VM6380
Portable vibration meter options for different rotating machinery measurement requirements.
Wintact Vibration Meters
Suitable for routine factory machinery vibration checks.
Benetech Vibration Meters
Additional portable options for general industrial maintenance and vibration measurement.
The appropriate model depends on the required vibration parameters and application.
A Simple Factory Maintenance Strategy
Start with your most critical rotating machines.
For each machine:
Inspect
↓
Measure Vibration
↓
Check Temperature
↓
Record RPM & Load
↓
Compare Historical Data
↓
Investigate Changes
↓
Perform Maintenance
↓
Re-measure
This turns routine preventive maintenance into a more condition-focused process.
Looking for a Vibration Meter for Preventive Maintenance in Malaysia?
MTM Precision Sdn Bhd supplies vibration meters and industrial testing instruments for factories, maintenance contractors, HVAC teams, facility management companies and engineering departments in Malaysia.
Applications include:
Motor → Bearing → Pump → Fan → Compressor → Gearbox → Generator → HVAC → Production Machinery
Contact MTM Precision for assistance selecting suitable vibration measurement equipment for your preventive maintenance and machine condition monitoring programme.
MTM Precision Sdn Bhd
Website: www.mtmpre.com.my
WhatsApp: +6016-660 7346
Email: mtmpre@yahoo.com
Showroom & Service Centre
No. 29-1 & 29-2, Jalan Bandar 18,
Pusat Bandar Puchong,
47160 Puchong, Selangor, Malaysia.
20 Aug 2026