Motor Bearing Vibration: Warning Signs, Measurement & Troubleshooting Malaysia
Electric motor bearings are among the most important components to monitor in factory maintenance.
When a motor bearing begins to deteriorate, the motor may continue operating for some time. During this period, maintenance personnel may notice changes in vibration, temperature, noise or operating behaviour.
A portable vibration meter provides a practical method for checking motor vibration and establishing a condition trend.
For factories, HVAC systems, facility management teams and industrial maintenance engineers in Malaysia, motor bearing vibration monitoring can become part of a preventive or predictive maintenance programme.
Why Monitor Electric Motor Bearings?
Electric motors are used almost everywhere in industrial facilities.
They drive equipment such as:
Pumps → Fans → Blowers → Compressors → Gearboxes → Conveyors → Production Machines
A bearing problem in the motor can eventually affect the entire driven system.
Routine monitoring gives maintenance teams an opportunity to detect changing behaviour before the problem develops into an unexpected shutdown.
What Causes Motor Bearing Problems?
Possible causes include:
Normal wear
Lubrication problems
Contamination
Incorrect bearing installation
Misalignment
Excessive mechanical loading
Shaft problems
Electrical effects in some applications
Mechanical looseness
Poor operating environment
A bearing should therefore not be viewed in isolation.
The condition of the entire motor and driven machine can affect bearing life.
What Are the Warning Signs of Motor Bearing Problems?
Possible warning signs include:
Increasing vibration
Unusual bearing noise
Increasing bearing temperature
Rough running
Lubrication changes
Repeated bearing failures
Sometimes more than one symptom appears together.
For example:
Increasing Vibration + Increasing Temperature + Abnormal Noise
may justify more urgent inspection than a single observation alone.
Can You Detect a Bad Motor Bearing with a Vibration Meter?
A vibration meter can help identify changes in machine vibration.
For example, if the same motor bearing location normally measures:
1.5 mm/s
and later measurements show:
1.7 → 2.1 → 2.8 → 3.6 mm/s
the trend indicates that machine behaviour has changed.
However, this does not automatically prove that the bearing itself is defective.
Other mechanical conditions can also increase vibration.
Where Should Motor Vibration Be Measured?
Electric motors commonly have two main bearing areas:
Drive End — DE
The end connected to the driven equipment.
Non-Drive End — NDE
The opposite end.
For routine condition monitoring, both locations can be checked.
A simple route is:
Motor NDE → Motor DE
For a motor-driven pump:
Motor NDE → Motor DE → Pump DE → Pump NDE
This provides more information about the complete machine train.
Horizontal, Vertical and Axial Measurements
Depending on the maintenance programme, measurements may be taken in:
Horizontal
Vertical
Axial
For example:
M01-DE-H
Motor 01 → Drive End → Horizontal
M01-DE-V
Motor 01 → Drive End → Vertical
M01-DE-A
Motor 01 → Drive End → Axial
Using fixed point codes makes historical comparison easier.
Why Measurement Location Matters
Avoid measuring wherever it is convenient each time.
If one measurement is taken from a rigid bearing housing and the next is taken from a thin motor cover, the readings may not be comparable.
For condition monitoring:
Same Machine + Same Point + Same Direction + Similar Operating Condition
provides more useful trend data.
Which Vibration Parameter Should You Measure?
Portable vibration meters may provide several parameters.
Vibration Velocity
Usually expressed in:
mm/s
Commonly used for overall rotating machinery vibration assessment and trending.
Vibration Acceleration
Usually expressed in:
m/s² or g
Can provide useful information for higher-frequency vibration and certain bearing-related conditions.
Vibration Displacement
Often expressed in:
µm
Used for particular machinery and lower-frequency vibration applications.
The appropriate parameter depends on the motor, application and monitoring objective.
Why Acceleration Can Be Useful for Bearings
Rolling-element bearing defects can generate higher-frequency vibration components.
Acceleration measurement can therefore provide useful additional information in certain bearing applications.
However, detailed bearing diagnosis can require techniques beyond a basic overall acceleration reading.
Advanced diagnosis may involve:
Frequency analysis
Bearing defect frequencies
Envelope analysis
Time waveform analysis
A portable vibration meter is particularly useful as a first-line screening instrument.
Motor Bearing Vibration Example
Consider Motor 05.
Monthly Drive End horizontal readings are:
January — 1.4 mm/s
February — 1.5 mm/s
March — 1.5 mm/s
April — 1.8 mm/s
May — 2.4 mm/s
June — 3.2 mm/s
The maintenance engineer should not simply wait until the motor fails.
The increasing trend provides a reason to investigate.
What Should You Check When Motor Bearing Vibration Increases?
A useful inspection sequence includes:
Bearing Condition
↓
Lubrication
↓
Alignment
↓
Rotor / Driven Equipment Balance
↓
Motor Mounting
↓
Coupling
↓
Foundation
The actual source may not be inside the bearing.
Motor Bearing vs Misalignment
Poor alignment between a motor and driven machine can place additional forces on the bearings.
For example:
Motor → Coupling → Pump
If the shafts are misaligned, vibration may increase around both motor and pump bearing locations.
Replacing the motor bearing without correcting alignment may result in the same problem returning.
Motor Bearing vs Imbalance
Rotor or driven-equipment imbalance can also create vibration at the motor bearings.
For example, an unbalanced fan can transmit vibration through the drive system.
The motor bearing may show elevated vibration even though the original source is the fan.
Measure the complete machine where possible.
Motor Bearing vs Mechanical Looseness
Loose motor mounting can produce or amplify vibration.
Check:
Motor feet
Mounting bolts
Base plate
Shims
Foundation
A loose motor should not immediately be diagnosed as a failed bearing.
Lubrication and Motor Bearing Vibration
Bearing lubrication requires the correct:
Lubricant
Quantity
Interval
Application method
Both insufficient and inappropriate lubrication practices can affect bearing operation.
If vibration increases after lubrication work, investigate the complete condition rather than assuming that more grease is automatically the solution.
Motor Bearing Temperature
Temperature monitoring can complement vibration measurement.
Maintenance teams may use:
Vibration Meter + Infrared Thermometer
or:
Vibration Meter + Thermal Imager
to obtain additional information.
If vibration and temperature are both trending upward, further inspection may be justified.
Don't Rely Only on Motor Noise
Experienced technicians often recognize abnormal motor sounds.
But noise assessment can be subjective and affected by surrounding machinery.
A vibration meter provides numerical information.
Instead of:
“Motor 3 sounds worse.”
you can record:
Motor 3 DE-H = 3.4 mm/s
This makes maintenance records more useful.
Compare DE and NDE Readings
Measuring both bearing locations can provide useful clues.
For example:
NDE = 1.6 mm/s
DE = 3.9 mm/s
The significantly higher Drive End reading may help focus the inspection around the drive side, coupling or driven equipment.
It does not by itself prove the exact fault, but it helps guide troubleshooting.
Why RPM Should Be Recorded
Motor speed affects vibration behaviour.
If the motor is controlled by a variable-frequency drive, measurements taken at different speeds may not be directly comparable.
Record RPM or operating frequency where practical.
For trending, compare similar operating conditions.
What Is an Acceptable Motor Bearing Vibration Level?
There is no universal vibration value suitable for every electric motor.
Assessment depends on:
Motor size
Machine type
Speed
Mounting
Measurement location
Operating condition
Manufacturer recommendations
Applicable machinery standards
Relevant standards such as the appropriate ISO 20816 series may be used where applicable.
Always confirm the correct criteria for the specific machine.
Why Trending Is So Important
Suppose two motors both measure:
3.0 mm/s
Motor A historically operates around:
2.8–3.1 mm/s
Motor B historically operates around:
1.0–1.2 mm/s
Although the current numerical value is identical, the significance may be very different.
Motor B has experienced a much larger change from its baseline.
This is why condition monitoring should not rely only on generic alarm numbers.
How Often Should Motor Bearings Be Checked?
Inspection frequency depends on:
Machine criticality
Operating hours
Previous failure history
Production importance
Environment
Maintenance strategy
A critical 24-hour production motor may require more attention than a small non-critical motor used occasionally.
Motor Bearing Predictive Maintenance
A simple programme can follow:
Identify Critical Motors
↓
Create DE/NDE Measurement Points
↓
Record Baseline Vibration
↓
Measure Periodically
↓
Trend Results
↓
Investigate Significant Changes
This can be implemented with a portable vibration meter before investing in more complex permanent monitoring systems.
Vibration Meter vs Vibration Analyzer for Motor Bearings
A vibration meter is useful for:
Routine inspection
Overall vibration
Baseline measurement
Trending
Identifying abnormal motors
A vibration analyzer may be needed for:
Detailed bearing fault diagnosis
Frequency spectrum analysis
Bearing defect frequency analysis
Advanced vibration investigation
A practical strategy is:
Vibration Meter Screening → Advanced Analysis When Needed
Motor Bearing Vibration Meter Options from MTM Precision
MTM Precision supplies vibration measurement equipment for electric motor and bearing maintenance applications in Malaysia.
Showa Sokki SH-1332B
Suitable for professional industrial vibration measurement and machine maintenance applications.
Landtek VM6310 / VM6360 / VM6380
Portable vibration meter options for different motor and machinery vibration measurement requirements.
Wintact Vibration Meters
Suitable for routine motor bearing, pump, fan and general machinery vibration inspection.
Benetech Vibration Meters
Additional portable options for general industrial vibration measurement and maintenance applications.
The appropriate model depends on the required vibration parameters and intended application.
Don't Wait for the Bearing to Fail
The ideal time to begin measuring motor vibration is not after the motor starts making severe noise.
Measure while the motor is healthy.
Establish its normal vibration.
Then monitor:
Normal → Small Change → Increasing Trend → Investigation
This is the foundation of vibration-based machine condition monitoring.
Looking for a Motor Bearing Vibration Meter in Malaysia?
MTM Precision Sdn Bhd supplies vibration meters and industrial testing instruments for factories, maintenance contractors, HVAC teams, facility management and engineering companies in Malaysia.
Applications include:
Electric Motors → Bearings → Pumps → Fans → Compressors → Gearboxes → Generators → Production Machinery
Contact MTM Precision for assistance selecting suitable vibration measurement equipment for motor bearing inspection, troubleshooting and predictive maintenance.
MTM Precision Sdn Bhd
Website: www.mtmpre.com.my
WhatsApp: +6016-660 7346
Email: mtmpre@yahoo.com
Showroom & Service Centre
No. 29-1 & 29-2, Jalan Bandar 18,
Pusat Bandar Puchong,
47160 Puchong, Selangor, Malaysia.
20 Aug 2026