Pump Cavitation and Vibration: How to Identify Cavitation Problems Malaysia
A pump suddenly becomes noisy and vibration starts increasing.
Is the bearing damaged? Is the motor misaligned? Or could the pump be experiencing cavitation?
Pump cavitation is an important condition to consider when troubleshooting centrifugal pumps. It can produce abnormal noise, vibration and reduced pump performance, and prolonged severe cavitation may damage pump components.
For maintenance engineers, HVAC technicians, water treatment operators and factory maintenance teams in Malaysia, vibration measurement can provide useful supporting information when investigating pump problems.
What Is Pump Cavitation?
Cavitation occurs when local pressure in the liquid falls sufficiently for vapour bubbles to form.
As these bubbles move into regions of higher pressure, they collapse.
Repeated bubble formation and collapse can create:
Noise
Vibration
Pressure fluctuations
Surface damage
Reduced pump performance
Cavitation is therefore not simply a vibration problem.
It is related to the hydraulic operating condition of the pump.
What Does Pump Cavitation Sound Like?
Technicians often describe severe cavitation as sounding similar to:
Gravel → Stones → Crackling → Rattling
inside the pump.
The exact sound varies according to the pump and operating condition.
If a normally smooth-running pump suddenly develops unusual noise together with increased vibration, cavitation should be one of the conditions considered.
However, noise alone should not be used to confirm the diagnosis.
What Causes Pump Cavitation?
Possible contributing conditions include:
Insufficient suction pressure
Excessive suction lift
Restricted suction piping
Blocked strainer
Partially closed suction valve
High liquid temperature
Excessive pump speed
Incorrect operating point
Inadequate available NPSH
Poor suction piping design
The actual cause should be investigated from the hydraulic system rather than only the pump itself.
What Is NPSH?
NPSH means:
Net Positive Suction Head
It is an important concept in pump cavitation.
In simplified terms, the pump installation must provide adequate pressure at the suction side to reduce the risk of the liquid vaporizing where it should remain liquid.
Pump manufacturers commonly provide NPSH-related information for their equipment.
When investigating suspected cavitation, the actual system operating condition should be compared with the pump requirements.
Can Cavitation Cause High Vibration?
Yes.
Bubble collapse and unstable hydraulic conditions can contribute to pump vibration.
Depending on severity, vibration may be detected around the:
Pump casing
Pump bearings
Motor-pump assembly
Connected structure
However, high pump vibration does not automatically mean cavitation.
Other possible causes include:
Bearing Wear → Misalignment → Impeller Imbalance → Mechanical Looseness → Pipe Strain → Foundation Problems
A structured troubleshooting process is required.
How Can a Vibration Meter Help?
A portable vibration meter allows maintenance personnel to quantify machine vibration.
Instead of saying:
“The pump seems to be vibrating more.”
the technician can record:
Pump DE Horizontal: 4.2 mm/s
and compare it with previous measurements.
Depending on the vibration meter, parameters may include:
Vibration velocity
Vibration acceleration
Vibration displacement
For general rotating machinery condition trending, vibration velocity in mm/s is commonly encountered.
Where Should Pump Vibration Be Measured?
For a typical motor-driven pump, establish repeatable measurement locations such as:
Motor NDE → Motor DE → Pump DE → Pump NDE
Measurements may be taken in:
Horizontal
Vertical
Axial
The exact measurement method should suit the equipment and monitoring objective.
For trending, use the same locations whenever practical.
Example of a Pump Cavitation Investigation
Suppose a cooling water pump normally records:
Pump DE: 2.0 mm/s
During one inspection, the technician finds:
Pump DE: 4.6 mm/s
The pump also sounds unusually noisy.
Instead of immediately replacing the bearing, the maintenance team checks:
Suction valve position
Suction strainer
Tank level
Suction pressure
Flow condition
Pump operating point
A restricted suction condition is discovered.
After correcting the hydraulic problem, vibration and noise are checked again.
This type of before-and-after measurement can help verify whether machine behaviour improved.
Cavitation vs Bearing Failure
Both conditions can produce noise and vibration.
Possible Cavitation Clues
Noise changes with flow or operating condition
Hydraulic performance may change
Suction conditions may be abnormal
Vibration may change when the operating point changes
Possible Bearing Problem Clues
Bearing temperature may increase
Bearing-related noise may develop
Vibration may trend upward over time
Lubrication condition may be abnormal
These are only clues.
Detailed diagnosis may require additional measurements and inspection.
Cavitation vs Misalignment
Misalignment is a mechanical condition involving connected shafts.
Cavitation is primarily a hydraulic phenomenon.
Both can cause pump vibration.
This is why measuring vibration alone may identify that something is wrong without proving the root cause.
Check both the mechanical and hydraulic sides of the pump system.
Cavitation vs Impeller Imbalance
An impeller can become unbalanced because of:
Deposits
Corrosion
Erosion
Damage
Foreign material
Impeller imbalance can produce vibration even when suction conditions are normal.
Cavitation itself may also contribute to impeller surface deterioration over time.
A pump can therefore have more than one condition affecting vibration.
Check the Suction Side First
When cavitation is suspected, inspect the suction system.
Possible checks include:
Tank Level → Suction Valve → Strainer → Suction Pipe → Pressure → Liquid Temperature
A partially blocked strainer, for example, may restrict flow and contribute to poor suction conditions.
Replacing the pump bearing would not solve this hydraulic problem.
Check Pump Operating Point
A centrifugal pump should operate within an appropriate range for its design and system.
Operating significantly away from the intended condition can create hydraulic problems and affect vibration.
Maintenance personnel should consider:
Flow
Pressure
Pump curve
System resistance
Speed
when troubleshooting recurring pump vibration.
HVAC Pump Cavitation
Cavitation can be relevant to HVAC systems containing:
Chilled water pumps
Condenser water pumps
Cooling tower pumps
Circulation pumps
Facility teams may notice:
Noise + Vibration + Unstable Performance
Routine vibration trending can help determine when pump behaviour changes.
Water Treatment Pump Cavitation
Water and wastewater facilities use many pumps continuously.
Applications include:
Raw water pumping
Process water
Chemical transfer
Circulation
Treated water
Wastewater pumping
Critical pumps can be included in a vibration condition monitoring route.
This allows operators to track mechanical behaviour alongside process parameters.
Factory Process Pump Vibration
Factories may use pumps for:
Cooling water
Chemicals
Process liquids
Boiler systems
Water treatment
Production processes
Unexpected pump failure can affect production.
A portable vibration meter allows maintenance teams to monitor multiple pump sets using one instrument.
Why Trending Is Important
Consider:
January — 1.8 mm/s
February — 1.9 mm/s
March — 2.0 mm/s
April — 2.1 mm/s
May — 3.0 mm/s
June — 4.3 mm/s
The increasing trend tells maintenance personnel that the machine condition has changed.
The next step is not simply:
“Replace bearing.”
Instead:
Measure → Inspect → Identify Mechanical or Hydraulic Cause → Correct → Re-measure
Combine Vibration with Process Data
Pump condition monitoring becomes more useful when vibration is considered together with:
Suction pressure
Discharge pressure
Flow rate
Temperature
Motor current
Noise
Bearing temperature
For example, high vibration together with abnormal suction pressure may point the investigation in a different direction from high vibration accompanied by increasing bearing temperature.
Can a Basic Vibration Meter Diagnose Cavitation?
A portable vibration meter can detect and quantify vibration changes.
However, a single overall vibration value usually cannot conclusively identify cavitation.
More detailed vibration analysis and hydraulic investigation may be required.
The vibration meter is particularly useful for:
Routine pump inspection
Baseline measurements
Trending
Identifying abnormal pumps
Checking before and after corrective work
Vibration Meter Options from MTM Precision Malaysia
MTM Precision supplies vibration measurement instruments for pump maintenance and industrial machine condition monitoring applications.
Showa Sokki SH-1332B
Suitable for professional industrial vibration measurement and machinery maintenance applications.
Landtek VM6310 / VM6360 / VM6380
Portable vibration meter options for different pump and rotating machinery measurement requirements.
Wintact Vibration Meters
Suitable for routine pump, motor, bearing and general machinery vibration checks.
Benetech Vibration Meters
Additional portable options for industrial vibration measurement and maintenance applications.
The suitable model depends on required measurement parameters and application.
Pump Vibration Troubleshooting Checklist
When a pump shows abnormal vibration, investigate systematically:
1. Confirm the vibration reading
2. Compare historical measurements
3. Check motor and pump bearings
4. Check alignment
5. Inspect mounting and foundation
6. Consider impeller condition
7. Check suction conditions
8. Check flow and pressure
9. Consider cavitation
10. Re-measure after corrective work
This helps avoid unnecessary component replacement.
Looking for a Pump Vibration Meter in Malaysia?
MTM Precision Sdn Bhd supplies vibration meters and industrial testing instruments for factories, HVAC contractors, facility management teams, water treatment operators and maintenance engineers in Malaysia.
Applications include:
Pump → Motor → Bearing → Fan → Compressor → Gearbox → Generator → HVAC → Factory Machinery
Contact MTM Precision for assistance selecting suitable vibration measurement equipment for pump troubleshooting, preventive maintenance and machine condition monitoring.
MTM Precision Sdn Bhd
Website: www.mtmpre.com.my
WhatsApp: +6016-660 7346
Email: mtmpre@yahoo.com
Showroom & Service Centre
No. 29-1 & 29-2, Jalan Bandar 18,
Pusat Bandar Puchong,
47160 Puchong, Selangor, Malaysia.
20 Aug 2026