Where Should You Place a Temperature & Humidity Data Logger Malaysia?
Where Should You Place a Temperature & Humidity Data Logger Malaysia?
You can buy a good temperature and humidity data logger, configure it correctly and record thousands of readings—but still collect misleading data if the logger is placed in the wrong location.
This is why data logger placement matters.
The correct location depends on what you are trying to measure.
A Benetech GM1365 Temperature & Humidity Data Logger can be used for general environmental monitoring in warehouses, laboratories, food-storage areas, electronics facilities, agriculture, archives and HVAC troubleshooting.
But before placing the logger, ask one question:
“What environment do I actually want this reading to represent?”
There Is No Universal “Best Location”
Customers sometimes ask:
“Where should I put the temperature logger?”
There is no single answer.
If you are investigating:
Warehouse Overall Condition
the location may be different from:
Loading Door Heat
or:
Air-Conditioning Performance
or:
Upper Rack Temperature
or:
Product Storage Condition
The measurement objective determines the logger position.
Mistake #1: Putting the Logger Where It Is Convenient
One common mistake is placing the logger:
“Here, because it is easy to reach.”
Convenience should not be the main reason.
A logger should be positioned where it can provide useful information about the environmental condition being investigated.
Otherwise, you may collect very accurate measurements that answer the wrong question.
Mistake #2: Directly Under the Air-Conditioning Outlet
Suppose you want to know the general temperature of a room.
Placing the logger directly under the air-conditioning outlet may produce a lower reading than the temperature experienced elsewhere.
That reading may correctly represent:
Air near the cooling outlet
but not:
Overall room conditions
If you specifically want to investigate the HVAC outlet, that position may be appropriate.
Again, the objective matters.
Mistake #3: Near a Heat Source
Avoid placing the logger close to:
Motors
Machinery
Lighting
Electrical equipment
Heating equipment
Hot pipes
unless the purpose is specifically to investigate that heat source.
Otherwise, the reading may represent a local hot spot rather than the general environment.
Mistake #4: Direct Sunlight
Direct sunlight can heat the instrument housing and influence the local measurement.
This can be especially relevant in:
Greenhouses
Warehouses near windows
Agricultural facilities
Rooms with strong afternoon sunlight
If you are trying to measure general ambient air conditions, avoid inappropriate direct solar exposure.
Mistake #5: Assuming One Logger Represents a Large Warehouse
Large warehouses can have significant environmental differences.
For example:
Loading Door → Outside air influence
Upper Rack → Potentially warmer
Lower Rack → Different temperature
External Wall → Solar influence
Centre Warehouse → More stable
HVAC Area → Cooler
One logger cannot automatically represent all these locations.
How to Place Data Loggers in a Warehouse
For preliminary warehouse investigation, consider several representative areas.
For example:
Logger A → Loading Area
Logger B → Centre Warehouse
Logger C → Upper Rack
Logger D → Lower Rack
Logger E → Far Corner
The data can then be compared over the same period.
This can reveal whether environmental conditions are relatively uniform or whether hot/cold/humid zones exist.
High vs Low Placement
Temperature can vary vertically.
Warm air and building heat loads may create different conditions at different heights.
In a high-rack warehouse, consider whether the stored products occupy:
Lower Level
Middle Level
Upper Level
If all products are stored across multiple heights, monitoring only at desk level may not tell the full story.
Where to Place a Logger in a Cold Room
Cold rooms can also contain temperature differences.
Potential areas to investigate include:
Near the door
Centre of storage
Near cooling airflow
Far from cooling source
Upper storage
Lower storage
However, placement should follow the actual monitoring objective and applicable storage requirements.
For critical cold-chain applications, formal temperature mapping procedures may be required.
Where to Place a Logger in a Laboratory
Laboratories can have local environmental differences.
Potential monitoring areas include:
Main Working Area
Instrument Area
Near Entrance
Sample Storage Area
Near Heat-Generating Equipment
If the objective is to record general laboratory conditions, avoid a location that is unusually influenced by a local heat or cooling source.
Where to Place a Logger for HVAC Troubleshooting
HVAC troubleshooting is different.
Here you may deliberately want to compare:
Supply Air Area
vs
Occupied Zone
vs
Problem Area
For example:
Logger A → Near HVAC Supply
Logger B → Centre of Room
Logger C → Customer Complaint Area
If Logger A remains cool while Logger C becomes warm every afternoon, this provides useful information for further investigation.
Where to Place a Logger in Food Storage
For food-storage applications, the logger location should relate to where the product is actually stored.
Potential factors include:
Storage rack position
Loading door
Air-conditioning
Refrigeration airflow
External wall
Product arrangement
The appropriate location and environmental limits depend on the product and quality requirements.
Where to Place a Logger in Electronics Storage
For electronics or component warehouses, users may want to understand both:
Temperature
and
Relative Humidity
Consider monitoring representative storage locations rather than simply placing the logger in the office area.
If certain racks or rooms are suspected of experiencing higher humidity, additional loggers can be placed there for comparison.
How Many Data Loggers Do You Need?
There is no universal number.
It depends on:
Facility size
Layout
Ceiling height
Number of rooms
HVAC design
Storage arrangement
Environmental variation
Monitoring objective
A small room may require only one monitoring point for a basic investigation.
A large warehouse may require several.
Start With a Preliminary Survey
If you do not know where the problem is, begin with a preliminary survey.
A practical workflow is:
Step 1 → Identify the Area
↓
Step 2 → Identify Possible Hot/Cold/Humid Locations
↓
Step 3 → Deploy Several Loggers
↓
Step 4 → Record Simultaneously
↓
Step 5 → Compare Data
↓
Step 6 → Investigate Abnormal Areas
This is often more effective than guessing.
Why Simultaneous Monitoring Is Better for Comparison
Suppose you use one logger:
Monday → Area A
Tuesday → Area B
But Monday and Tuesday may have different weather, production loads or HVAC conditions.
If the objective is to compare locations, simultaneous monitoring is usually more meaningful.
For example:
Same Monday–Wednesday Period
Logger A → Area A
Logger B → Area B
Logger C → Area C
Now the locations are being compared under the same time period.
Should the Logger Touch the Product?
Not necessarily.
There is an important difference between:
Air Temperature
and
Product Temperature
A GM1365 measuring surrounding environmental conditions does not automatically tell you the internal temperature of a product.
If actual product temperature is required, a different sensor or probe arrangement may be necessary.
Don't Move the Logger During the Monitoring Period
If possible, avoid repeatedly moving the logger after recording begins.
Moving it between locations can make the trend harder to interpret.
For professional monitoring, record:
Logger ID + Location + Start Time + End Time
If the logger must be moved, document when and where it was moved.
Label Multiple Loggers
If several GM1365 units are deployed, use a simple identification system.
For example:
GM1365-01 → Loading Door
GM1365-02 → Upper Rack
GM1365-03 → Lower Rack
GM1365-04 → Centre
This makes later data analysis much easier.
Take a Photo of the Logger Position
A simple but useful practice is to photograph each logger after installation.
The photo provides a record of:
Exact location
Height
Nearby equipment
Rack position
HVAC proximity
When reviewing the data several days later, this context can be extremely useful.
Placement Is Part of Measurement Quality
Measurement quality is not only:
Buy Accurate Instrument
It is:
Correct Instrument + Correct Configuration + Correct Placement + Correct Interpretation
A good logger placed incorrectly can produce misleading conclusions.
A modest logger used correctly can provide very useful information.
Benetech GM1365 for Multi-Point Environmental Investigation
Because GM1365 is reusable, businesses can use multiple units for environmental investigations such as:
Warehouse hot-spot identification
HVAC troubleshooting
Laboratory comparison
Food-storage monitoring
Electronics warehouse monitoring
Agricultural environment studies
Archive monitoring
The objective is not simply to collect data.
The objective is to understand where and when environmental conditions change.
Looking for Temperature Data Logger Placement Advice in Malaysia?
MTM Precision supplies the Benetech GM1365 Temperature & Humidity Data Logger and other environmental monitoring instruments in Malaysia.
If you are unsure how many loggers you need or where they should be positioned, tell us:
Application + Room/Warehouse Size + Monitoring Objective + Temperature/Humidity Requirement
We can help you determine a practical monitoring approach and suitable instrument.
Contact MTM Precision
MTM Precision Sdn Bhd
No. 29-1 & 29-2, Jalan Bandar 18,
Pusat Bandar Puchong,
47160 Puchong, Selangor, Malaysia.
Website: www.mtmpre.com.my
WhatsApp: +6016-660 7346
Email: mtmpre@yahoo.com
Correct Logger + Correct Location + Correct Data = Better Environmental Monitoring
MTM Precision Malaysia
23 Aug 2026