Heavy-Duty High-Current Power Diagnostics Without the Bulk: PEAKMETER 35mm Jaw AC Digital Clamp Meters for Malaysian Contractors
Walk into any main electrical switchroom, industrial plant room, or commercial chiller deck in Malaysia, and you quickly run into two competing challenges: thick main feeder cables carrying hundreds of amperes that small pocket clamps cannot physically wrap around, and heavy, oversized clamp meters that tire out your wrist after a full day of panel inspections. Worse still, trying to troubleshoot variable-speed chillers or factory conveyor drives with a standard clamp meter often leaves you staring at erratic, noise-distorted numbers.
Weighing an astonishingly light 189 grams while packing a generous 35mm jaw opening, the patented PEAKMETER PM2017A and PEAKMETER PM2017B AC Digital Clamp Meters give electrical contractors, HVAC specialists, and industrial maintenance engineers heavy-duty current capacity, CAT III 1000V safety protection, and specialized drive diagnostics in a slim, easy-handling frame.
High-Capacity 1000A Feeder & Panel Troubleshooting: The PEAKMETER PM2017A
When commissioning main incoming distribution boards, checking commercial generator outputs, or verifying heavy building loads, standard 400A or 600A clamp meters quickly run out of headroom. Built with a wide 35mm clamp jaw that closes cleanly around thick power cables, the PEAKMETER PM2017A delivers serious high-current muscle without weighing down your tool pouch:
-
Full 1000A AC Current & 1000V AC/DC Diagnostic Power: Accurately measures AC current across 20A, 200A, and 1000A ranges alongside True RMS accuracy, 1000V AC and DC voltage, 20MΩ resistance, 2mF capacitance, and 20kHz frequency—covering everything from main switchgear loads to motor run capacitors in one handheld instrument.
-
Frontline Safety Screening in Crowded Switchrooms: Certified to IEC 61010-1 and IEC 61010-2-032 (Shell CAT III 1000V / Clamp Shell CAT III 600V), the PM2017A pairs Non-Contact Voltage (NCV)detection with single-probe live-wire identification, a bright backlight, MAX/MIN capture, and Data Hold—helping technicians verify live conductors safely before clamping onto congested busbars.
Built for Variable Frequency Drives, Large Motor Capacitors & Thermal Checks: The PEAKMETER PM2017B
Across Malaysia’s manufacturing lines and modern commercial HVAC systems, Variable Frequency Drives (VFDs) and high-capacity motor starters are everywhere. When a chiller pump or factory exhaust fan trips,technicians need a clamp meter that filters out inverter harmonics, tests large motor capacitors, and checks for overheating lugs—without swapping tools mid-job.
Upgraded with a 6000-count backlit display in the exact same 189g, 35mm-jaw body, the PEAKMETER PM2017B AC Digital Clamp Meter turns complex industrial troubleshooting into a single-tool workflow:
-
Dedicated VFD Filtering for Clean Inverter & Motor Readings: Equipped with specialized VFD measurement mode alongside True RMS sensing, the PM2017B strips away high-frequency drive noise so engineers get stable, accurate voltage and current readings on variable-speed motors up to 600A AC.
-
Expanded 60mF Capacitance & K-Type Thermal Troubleshooting: Goes far beyond ordinary clamp meters by measuring capacitance up to 60 millifarads (60mF) and frequency up to 1MHz, while adding K-type thermocouple temperature measurement from -20°C to 1000°C—letting HVAC and plant engineers verify compressor capacitors and spot hot breaker terminals on the same service call.
Equip Your Team with Lightweight, High-Capacity PEAKMETER Clamp Meters
Whether your contractors need full 1000A AC feeder capacity with the PEAKMETER PM2017A, or VFD filtering, 60mF capacitance, and 1000°C thermal diagnostics with the PEAKMETER PM2017B, PEAKMETER delivers patented, safety-certified performance built for real-world Malaysian job sites.
For electrical contractors, HVAC specialists, industrial maintenance teams, and resellers across Malaysia looking for genuine PEAKMETER instruments, practical product recommendations, and responsive local support, MTM Precision Sdn. Bhd. is ready to assist your operations.
Contact MTM Precision
MTM Precision Sdn. Bhd.
Showroom & Service Centre
No. 29-1 & 29-2, Jalan Bandar 18,
Pusat Bandar Puchong,
47160 Puchong, Selangor, Malaysia
Email: mtmpre@yahoo.com
WhatsApp: +6016-660 7346
Office Tel: +603-80807172