Anchor Pull-Out Test vs Torque Test What Is the Difference? Malaysia

Anchor Pull-Out Test vs Torque Test What Is the Difference? Malaysia Is an Anchor Pull-Out Test the Same as a Torque Test? No. Anchor pull-out testing and torque testing are not the same test. Although both may be used in construction QA/QC involving anchors, bolts and fixings, they measure different things and require different equipment. In simple terms: Pull-Out Test → Measures tensile force, commonly in kN Torque Test → Measures rotational torque, commonly in Nm Using a torque wrench does not automatically replace a pull-out tester, and performing a pull-out test does not automatically satisfy a specified torque requirement. The correct test depends on the anchor system, installation procedure and project specification. Quick Comparison ItemAnchor Pull-Out TestTorque TestMain MeasurementTensile forceRotational torqueCommon UnitkNNmTypical EquipmentHydraulic pull-out testerTorque wrench / torque testerForce DirectionPulling / tensileRotationalTypical PurposeVerify anchor under specified tensile loadVerify specified tightening torqueSame Test?NoNo Understanding this distinction helps contractors avoid using the wrong equipment on site. What Is an Anchor Pull-Out Test? An anchor pull-out test applies tensile force to an installed anchor. Depending on the approved test procedure, the test may be used as: Proof-load testing Verification testing Ultimate or failure testing The force is commonly measured in: kN kilonewtons For example: Required Proof Load: 80kN The pull-out testing equipment applies and measures the required tensile force according to the approved procedure. What Is a Torque Test? A torque test involves applying or checking rotational torque. Torque is commonly expressed in: Nm newton metres Depending on the application, a specified installation torque may be required for certain mechanical anchor or bolted systems. A suitable torque wrench or torque-measurement device is normally used. kN and Nm Are Different This is important. kN measures force. Nm measures torque. They are not interchangeable. You should not say: “80kN equals how many Nm?” without a specific mechanical model and geometry. There is no universal direct conversion between an anchor pull-out force and installation torque. Why Contractors Sometimes Confuse the Two Both tests may involve: Anchors Bolts Construction QA/QC Installation verification Engineering specifications However, they assess different aspects of the installation. One measures tensile loading. The other measures rotational torque. Example Mechanical Anchor Installation Suppose a mechanical anchor installation procedure specifies a tightening torque. The installer may need to use an appropriate torque wrench during installation. Later, the project may separately require selected anchors to undergo proof-load testing. These are two different requirements. Completing one does not automatically satisfy the other. Example Chemical Anhor A chemical anchor may consist of: Chemical adhesive Threaded rod Concrete substrate The installation and testing requirements may involve factors such as: Hole diameter Hole cleaning Embedment Adhesive installation Curing Required proof load A pull-out tester may then be used where the project requires tensile testing. Do not assume that simply tightening the nut to a high torque proves the chemical anchorage's tensile performance. Can a Torque Wrench Perform an Anchor Pull-Out Test? No. A torque wrench measures or applies torque. It does not directly apply and measure the same tensile pull-out loading produced by a hydraulic anchor pull-out tester. If the specification requires: Anchor Proof Load: 100kN use the appropriate testing system and approved method. Can a Pull-Out Tester Check Bolt Tightening Torque? No. An anchor pull-out tester measures tensile force. If the project requires a bolt to be tightened or verified to a specified torque, suitable torque equipment is required. What Equipment Is Used for Pull-Out Testing? A typical professional anchor pull-out testing system may include: Hydraulic cylinder Hydraulic pump Force measurement/display system Pull rod Anchor adapters Reaction arrangement For suitable applications, the Langry APT200 Anchor Pull-Out Tester provides a measurement range up to: 200kN approximately a 20-ton class capacity. What Equipment Is Used for Torque Testing? Depending on the requirement, equipment may include: Manual torque wrench Digital torque wrench Torque tester Torque calibration equipment The correct instrument depends on the required torque range and procedure. What Is Proof-Load Testing? Proof-load testing generally involves applying a predetermined tensile load to an installed anchor according to an approved procedure. For example: Required Proof Load: 60kN The operator applies the required tensile force and assesses the anchor according to the specified acceptance criteria. This is not a torque measurement. What Is Installation Torque? Installation torque is a rotational tightening requirement associated with certain fasteners or anchoring systems. For example, a manufacturer may specify a tightening torque for a particular anchor installation. That value should be followed according to the approved installation instructions. It should not be replaced with a guessed pull-out force. Does Higher Torque Mean Higher Pull-Out Strength? Do not make this assumption. Anchor performance depends on many factors, including: Anchor design Installation method Concrete Embedment Edge distance Spacing Hole condition Anchor type Torque and pull-out force should be treated according to their respective engineering requirements. Does a High Pull-Out Result Mean the Bolt Was Tightened Correctly? Not necessarily. A pull-out test measures tensile behaviour under the defined test conditions. It does not automatically verify that every installation step, including any specified tightening torque, was performed correctly. Mechanical Anchor QA/QC For mechanical anchor installations, QA/QC may involve checks such as: Correct anchor product Correct hole diameter Correct embedment Proper setting Specified tightening procedure Concrete condition Anchor position Where required, pull-out testing may provide an additional verification step. Chemical Anchor QA/QC Chemical anchor QA/QC may involve: Correct drilling Correct hole diameter Hole cleaning Correct embedment Adhesive installation Curing Anchor identification Where specified, selected anchors may then undergo pull-out or proof-load testing. Which Test Does My Project Need? Check the project documentation. Possible sources include: Structural drawings Project specification Approved method statement Anchor manufacturer's requirements Consultant instructions Engineer requirements Do not choose the test simply because you already own the equipment. What If the Specification Says “Torque Test”? Use the specified torque-testing method and appropriate equipment. Do not replace it with an anchor pull-out test unless the responsible project authority approves a revised procedure. What If the Specification Says “Pull-Out Test”? Confirm: Required load in kN Anchor type Anchor size Test quantity Holding time where required Acceptance criteria Reporting requirements Then select the appropriate pull-out tester. What If the Specification Requires Both? Then both requirements should be addressed. For example: Installation Stage Specified torque is applied to the mechanical anchor. Verification Stage Selected anchors undergo proof-load testing according to the approved procedure. One requirement does not automatically cancel the other. Pull-Out Test vs Torque Test for Faade Anchors Faade systems may use: Chemical anchors Mechanical anchors Curtain wall brackets Steel fixing plates The required inspection and testing method depends on the approved faade design and project specification. Do not assume every faade anchor requires the same test. Pull-Out Test vs Torque Test for Structural Steel Structural steel installations may involve: Base plates Brackets Support frames Post-installed anchors Bolted connections Different connections can have different inspection requirements. A structural steel contractor should identify whether the specification refers to: Anchor tensile testing or Bolt tightening / torque control or both. Common Mistake 1 Using Torque as Proof of Pull-Out Capacity A contractor tightens an anchor and says: “Very tight, so the anchor is strong.” This is not a substitute for a specified tensile proof-load test. Common Mistake 2 Converting kN Directly to Nm There is no simple universal conversion. They represent different physical quantities. Common Mistake 3 Performing the Test You Have Equipment For The correct approach is: Requirement → Test Method → Equipment not: Equipment Available → Invent a Test Common Mistake 4 Not Checking Units Before testing, verify whether the specification states: kN or Nm Confusing these units can lead to major site errors. Langry APT200 for Pull-Out Testing The Langry APT200 is designed for force measurement in anchor pull-out testing applications. Key specifications include: SpecificationLangry APT200Measurement Range0200kNApproximate Capacity20 TonCylinder Centre Hole35mmCylinder Stroke70mmCommon AnchorageΦ6Φ25Pull RodM24ConverterM6M22Data Storage500 RecordsAccuracy ClassificationEN ISO 7500-1 Class 1 It should not be confused with a torque-measuring instrument. Which Langry Capacity Do I Need? For pull-out testing, Langry offers different measurement ranges: ModelMaximum RangeAPT100100kNAPT200200kNAPT300300kN Choose according to the required tensile test load and actual anchor configuration. What Information Should You Send MTM Precision? If you are unsure whether you need a pull-out tester or torque equipment, send: Application + Anchor Type + Anchor Size + Required Test Specification For pull-out tester selection, also provide: Required kN + Site Photo For example: M16 Chemical Anchor + Required Proof Load 120kN + Faade Bracket + Photo This allows the requirement to be understood more accurately. Frequently Asked Questions Is pull-out testing the same as torque testing? No. Pull-out testing measures tensile force, while torque testing measures rotational torque. What unit is used for an anchor pull-out test? Force is commonly measured in kN. What unit is used for torque? Torque is commonly expressed in Nm. Can I convert kN directly to Nm? No universal direct conversion applies because force and torque are different physical quantities. Can a torque wrench perform a pull-out test? No. A suitable pull-out testing system is required for tensile anchor testing. Can Langry APT200 measure torque? No. APT200 is an anchor pull-out testing system measuring tensile force. Can a project require both torque and pull-out testing? Yes, depending on the anchor system and project requirements. How do I know which test is required? Check the approved project specification, method statement, anchor system requirements and engineer or consultant instructions. Where can I buy an anchor pull-out tester in Malaysia? Contact MTM Precision Sdn. Bhd. for Langry APT-series model selection and current quotation. Anchor Pull-Out Testing & Construction QA/QC Equipment Malaysia MTM Precision supplies professional testing equipment for: Main contractors Faade contractors Structural steel contractors M&E contractors QA/QC departments Inspection companies Testing laboratories For anchor pull-out tester selection, provide: Anchor Type + Anchor Size + Required Test Load + Application + Site Photo This helps determine whether the Langry APT100, APT200 or APT300 is suitable for the required testing range. Contact MTM Precision MTM Precision Sdn. Bhd. Showroom & Service Centre No. 29-1 & 29-2, Jalan Bandar 18, Pusat Bandar Puchong, 47160 Puchong, Selangor, Malaysia 🌐 Website: www.mtmpre.com.my 📧 Email: mtmpre@yahoo.com 📱 WhatsApp: +6016-660 7346 For Anchor Pull-Out Test vs Torque Test Malaysia, Langry APT-series anchor testing equipment, model selection and current quotation enquiries, contact MTM Precision.

12 Aug 2026