Can You Retest an Anchor After a Failed Pull-Out Test? Malaysia
Can You Retest an Anchor After a Failed Pull-Out Test? Malaysia
Can the Same Anchor Be Tested Again After Failure?
A common question after an anchor pull-out test failure is:
“Can we just test the same anchor again?”
The answer is:
Not automatically.
Whether the same anchor can be retested depends on what happened during the first test, whether the anchor or surrounding concrete was changed or damaged, the approved test procedure, and the responsible engineer or consultant’s requirements.
A second test should not simply be performed because the first result was inconvenient.
Why Retesting the Same Anchor Can Be Problematic
The first pull-out test may already have changed the condition of the anchoring system.
Possible changes include:
Anchor movement
Bond damage
Concrete cracking
Local concrete damage
Thread damage
Plastic deformation
Partial pull-out
Disturbance of the test connection
If the anchor condition has changed, a second test may no longer represent the original installed condition.
Example 1 – Anchor Pulled Out During the First Test
Suppose the required load was:
80kN
but the anchor started pulling out at:
55kN
The anchor has already experienced physical movement.
Simply releasing the load and testing it again does not restore the original installation.
The failed result should be documented and the project’s approved failure procedure should be followed.
Example 2 – Concrete Cracked During Testing
If the surrounding concrete cracks during the first test, the base material condition has changed.
A second test on the same anchor may therefore represent a different condition from the original test.
The responsible project team should review the situation before any retesting.
Example 3 – Test Setup Was Wrong
There are situations where the first result may have been affected by the test setup rather than the anchor itself.
For example:
Wrong adapter
Poor alignment
Unstable reaction arrangement
Slipping connection
Incorrect target load
Equipment problem
In such cases, the project team may determine that a corrected retest is appropriate.
However, the first test should still be documented.
Retest Is Different from Hiding the First Result
A retest should not be used to erase an earlier failure.
A professional record should show:
First test result
Reason the first test was considered invalid or failed
Corrective action
Retest result
Relevant approval or instruction
This maintains traceability.
Who Decides Whether Retesting Is Allowed?
Depending on the project, the decision may come from:
Structural engineer
Façade engineer
Consultant
Main contractor QA/QC team
Approved method statement
Project specification
Approved failure procedure
The test operator should not make the decision independently if the project requires approval.
When Might a Retest Be Considered?
A retest may potentially be considered where the first test was affected by a clearly identified testing issue.
Examples can include:
Incorrect adapter used
Test connection slipped
Reaction setup moved
Wrong anchor identification
Wrong test load used
Measurement issue
Approved procedure not followed
The actual decision should still follow the project requirements.
When Should the Same Anchor Normally Not Be Assumed Suitable for Retesting?
Particular caution is required where the first test caused:
Permanent anchor movement
Partial pull-out
Concrete cracking
Concrete breakout
Bond damage
Steel deformation
Visible anchor damage
In these situations, the original anchoring condition may no longer exist.
What About a Proof Test That Was Stopped Early?
Suppose a proof test was stopped because of an external issue before the required load was reached.
For example:
Site access issue
Safety interruption
Equipment setup problem
Witness requested the test to stop
Whether the anchor can be retested depends on the approved procedure and whether the first loading changed the anchor condition.
Do not assume automatically.
What If the Adapter Slipped?
If the pulling adapter slips before the anchor is properly loaded, the event may be a connection failure rather than an anchor failure.
The operator should:
Stop the test
Inspect the thread
Inspect the adapter
Confirm whether the anchor was damaged
Record the event
Follow the approved procedure before retesting
Do not simply tighten the adapter and continue without checking.
What If the Tester Was Misaligned?
Poor alignment can introduce side loading or bending.
If misalignment is discovered, the test should be stopped and the setup reviewed.
Whether the same anchor can then be retested depends on:
Maximum force already applied
Anchor movement
Concrete condition
Project procedure
Engineering instruction
What If the Wrong Test Load Was Used?
Suppose the project required:
60kN
but the operator mistakenly loaded the anchor to:
90kN
This is not simply a matter of resetting the tester and repeating at 60kN.
The anchor has already experienced a higher load.
The event should be documented and reviewed by the responsible project team.
What If the First Test Was Below the Required Load?
Suppose:
Required Load: 80kN
First Test Stopped at: 40kN
If there was no damage or abnormal behaviour, can the test continue or be repeated?
Possibly, depending on the approved procedure and reason for stopping.
The key point is that the operator should not decide solely based on convenience.
Failed Anchor vs Invalid Test
These two situations should be distinguished.
Failed Anchor Test
The anchor does not satisfy the defined acceptance criteria.
Invalid Test
The test itself is not considered valid because of a setup, equipment or procedural issue.
This distinction is important when deciding whether a retest is appropriate.
Example of an Invalid Test
Possible invalid-test situations may include:
Wrong adapter caused slipping
Reaction fixture moved
Force reading malfunctioned
Wrong anchor was connected
Test setup did not follow the approved method
The project team may permit a corrected retest.
Example of a Genuine Failure
Possible genuine failure situations include:
Anchor pulls out
Concrete breaks
Bond fails
Required load cannot be reached
Movement exceeds defined criteria
In these cases, simply repeating the test on the same anchor may not be appropriate.
Should You Test a Replacement Anchor Instead?
Sometimes the approved corrective action may involve replacing or reinstalling the anchor and testing the new installation.
However, this should follow the responsible engineer or consultant’s requirements.
The new test should be clearly identified as a new or replacement anchor test.
Should You Test Another Nearby Anchor?
Additional testing may be required to determine whether the problem is isolated or widespread.
But the additional anchor should be selected according to:
Approved sampling plan
Engineer instruction
Consultant requirement
Failure procedure
Do not randomly choose the easiest nearby anchor.
How Should Retests Be Recorded?
A professional report should distinguish between:
Original test
Failed or invalid result
Reason for retest
Corrective action
Retest date
Retest result
For example:
Anchor ID: A-12
Initial Test: Invalid due to adapter slippage
Corrective Action: Adapter replaced and setup reviewed
Retest: Performed following approved instruction
This provides traceability.
Do Not Delete Failed Test Data
If the tester stores measurement records, failed or invalid readings should not simply disappear from the project history without explanation.
Good QA/QC requires honest documentation.
Why Photos Matter Before Retesting
Before any corrective work, take photographs of:
Anchor condition
Concrete condition
Adapter
Reaction setup
Failed connection
Visible movement
This helps the project team understand whether retesting is reasonable.
Chemical Anchor Retesting
Chemical anchors require special attention because the first loading may affect the bonded system.
If the anchor has moved, the bond condition may have changed.
Do not assume that simply allowing additional time for curing will restore the original installation.
Follow the project engineer’s instruction.
Mechanical Anchor Retesting
Mechanical anchors can also be affected by previous loading.
Potential issues include:
Expansion movement
Anchor slip
Concrete damage
Thread damage
Permanent deformation
Again, assess the actual condition before any second test.
What Should Be Checked Before an Approved Retest?
If retesting is authorised, confirm:
Reason for retest
Anchor condition
Concrete condition
Correct adapter
Correct reaction setup
Tester alignment
Required test load
Approved test procedure
Equipment condition
Calibration status where required
The second test should not repeat the same mistake.
Langry APT200 for Anchor Testing
For suitable professional applications, the Langry APT200 provides:
Measurement Range: 0–200kN
approximately:
20-ton class capacity
It can be used for proof-load and pull-out testing applications where the required load and physical test setup fall within the equipment’s capability.
Retesting Does Not Change Capacity Requirements
If the original test requirement is:
150kN
you still need equipment capable of performing the required test.
A 100kN tester does not become suitable simply because the first test failed.
Langry offers:
ModelMaximum RangeAPT100100kNAPT200200kNAPT300300kN
Choose according to the actual requirement.
Frequently Asked Questions
Can I retest the same anchor after it fails?
Not automatically. The first test may have changed or damaged the anchor or surrounding concrete.
Who decides whether retesting is allowed?
The decision should follow the approved project requirements and, where applicable, the responsible engineer or consultant’s instruction.
Can an invalid test be repeated?
Potentially yes, if the project determines the first test was invalid and the anchor condition remains suitable.
What is the difference between a failed test and an invalid test?
A failed test means the anchor did not satisfy the acceptance criteria. An invalid test means the test procedure or setup was not acceptable.
Can I retest after adapter slippage?
Possibly, after checking the anchor and test connection and following the approved procedure.
Can I retest after concrete cracking?
Do not assume so. The concrete condition has changed and engineering review may be required.
Can I test another nearby anchor instead?
Possibly, but the additional test location should follow the approved sampling or failure procedure.
Should the first failed result remain in the report?
Yes. Professional QA/QC should maintain traceability of the original result and any subsequent retest.
Can Langry APT200 be used for approved retesting?
It can be used where the required test falls within its 200kN range and the project permits retesting.
Anchor Pull-Out Testing Equipment Malaysia
MTM Precision supplies professional anchor pull-out testing equipment for:
Contractors
Structural contractors
Façade contractors
QA/QC teams
Inspection companies
Testing laboratories
For equipment selection, provide:
Anchor Type + Anchor Size + Required Test Load + Application + Site Photo
This helps determine whether Langry APT100, APT200 or APT300 is appropriate.
Contact MTM Precision
MTM Precision Sdn. Bhd.
Showroom & Service Centre
No. 29-1 & 29-2, Jalan Bandar 18,
Pusat Bandar Puchong,
47160 Puchong, Selangor, Malaysia
🌐 Website: www.mtmpre.com.my
📧 Email: mtmpre@yahoo.com
📱 WhatsApp: +6016-660 7346
For Langry Anchor Pull-Out Tester Malaysia, model selection, current quotation and professional construction testing equipment enquiries, contact MTM Precision.
12 Aug 2026