UV LED Curing Machine Not Curing Properly? Troubleshooting with Linshang LS137 Malaysia

UV LED Curing Machine Not Curing Properly? Troubleshooting with Linshang LS137 Malaysia

 

Your UV LED curing machine is running.

 

The UV lamp is ON.

 

The machine settings look normal.

 

But suddenly the product is not curing properly.

 

You may see tacky ink, soft coating, weak adhesive bonding or inconsistent production quality.

 

What should you check first?

 

One of the most important steps is to determine whether the actual UV exposure has changed.

 

The Linshang LS137 UV Energy Meter is designed for UV LED curing systems and can measure UV irradiance, accumulated UV energy and temperature, helping production and maintenance teams investigate curing problems using measurement data instead of guesswork.

 

What Are the Signs of Poor UV Curing?

 

Symptoms depend on the material and production process.

 

Common problems may include:

 

Tacky surface

 

Ink smearing

 

Poor scratch resistance

 

Soft coating

 

Weak adhesion

 

Incomplete adhesive curing

 

Reduced bond strength

 

Uneven curing

 

Inconsistent surface finish

 

Higher rejection rate

 

If these symptoms suddenly appear, do not assume immediately that the UV LED module needs replacement.

 

Several different variables can produce similar problems.

 

Problem 1 – UV LED Output Has Decreased

 

The UV LED lamp may still illuminate even when its measured output has changed.

 

Possible causes can include:

 

UV LED aging

 

Cooling problems

 

Power-system issues

 

Driver problems

 

Optical contamination

 

This is why visual inspection alone cannot confirm UV curing performance.

 

Measure the actual UV output.

 

Problem 2 – Accumulated UV Energy Is Too Low

 

This is an important distinction.

 

A UV LED source can still produce good peak irradiance while the product receives insufficient total UV exposure.

 

How?

 

Because UV curing depends on exposure time as well.

 

For example:

 

Strong UV + sufficient exposure time → adequate accumulated energy

 

but:

 

Strong UV + very short exposure time → potentially lower accumulated energy

 

This is particularly important in conveyor curing systems.

 

Problem 3 – Conveyor Speed Was Increased

 

Production teams naturally want higher output.

 

Suppose the conveyor speed was increased from:

 

20 m/min

 

to:

 

30 m/min

 

The product now spends less time underneath the UV source.

 

If no other parameter is changed, accumulated UV energy can decrease.

 

If curing problems began after increasing production speed, compare UV energy at the old and new conveyor settings.

 

Problem 4 – UV Lamp Distance Changed

 

Has the UV LED module been moved?

 

Has the fixture changed?

 

Is the new product taller or shorter?

 

Working distance can affect the UV irradiance reaching the curing surface.

 

A machine may still display exactly the same UV power percentage while the actual UV exposure at the product has changed.

 

Measure at the relevant production position.

 

Problem 5 – Optical Window Is Dirty

 

Industrial production environments are not always clean.

 

Depending on the process, optical surfaces may become contaminated by:

 

Dust

 

Ink mist

 

Coating residue

 

Oil

 

Process contamination

 

If less UV radiation passes through the optical path, curing performance can decrease.

 

A useful maintenance comparison is:

 

Measure → Clean according to manufacturer procedure → Measure Again

 

If UV output improves significantly, contamination may have contributed to the problem.

 

Problem 6 – Cooling Is Not Working Properly

 

UV LED systems depend on effective thermal management.

 

Cooling arrangements may include:

 

Fans

 

Air cooling

 

Heat sinks

 

Water cooling

 

Chillers

 

If cooling performance deteriorates, UV LED operating conditions may change.

 

Check the curing equipment according to the manufacturer's maintenance procedure.

 

Problem 7 – Wrong UV Power Setting

 

Before investigating complicated technical causes, confirm the basic machine settings.

 

Check whether:

 

The correct production recipe is selected

 

UV power has been changed

 

All required UV modules are enabled

 

The machine returned to the correct settings after maintenance

 

Sometimes the curing system itself is healthy—the production setting is simply wrong.

 

Problem 8 – Exposure Time Changed

 

In stationary curing applications, the product may require a specific exposure duration.

 

If the process changes from:

 

5 seconds

 

to:

 

3 seconds

 

the accumulated UV energy can also change.

 

This can happen because of:

 

PLC changes

 

Operator settings

 

Cycle-time optimization

 

Production-program changes

 

Check actual exposure duration rather than assuming it has remained unchanged.

 

Problem 9 – One UV LED Module Is Different

 

Some production machines use several UV LED modules.

 

For example:

 

Module A → Module B → Module C

 

If one module produces lower output, the overall curing process may change.

 

Where the equipment design and measurement procedure allow, compare the UV performance of the relevant curing zones under controlled conditions.

 

Problem 10 – The UV LED Is Fine, but the Material Changed

 

Not every curing failure is a UV lamp problem.

 

If measured UV conditions remain comparable with your known-good baseline, investigate:

 

Ink batch

 

Coating formulation

 

Adhesive

 

Photoinitiator system

 

Substrate

 

Material thickness

 

Application thickness

 

Surface preparation

 

Material storage condition

 

This is one of the biggest advantages of measurement.

 

A normal UV reading helps prevent unnecessary adjustments to a curing machine that may not be responsible for the defect.

 

What Does Linshang LS137 Measure?

 

The Linshang LS137 provides several parameters useful for troubleshooting:

 

UV Energy

 

UV Irradiance

 

Peak UV Irradiance

 

Measurement Duration

 

Temperature

 

Maximum Temperature

 

Instead of asking only:

 

“Is the UV lamp working?”

 

engineers can ask:

 

“Is the actual UV exposure still comparable with our normal production condition?”

 

LS137 for UV LED Sources

 

The Linshang LS137 is designed for UV LED curing applications.

 

Its spectral response is approximately:

 

340–420 nm

 

and it is calibrated using a:

 

395 nm UV LED source

 

Common industrial UV LED curing wavelengths can include:

 

365 nm

 

385 nm

 

395 nm

 

405 nm

 

Always confirm the actual wavelength of your curing equipment before selecting a UV meter.

 

High-Intensity UV LED Measurement

 

Industrial UV curing systems can produce very high irradiance.

 

The LS137 supports UV irradiance measurement up to:

 

40,000 mW/cm²

 

This makes it relevant to many high-intensity UV LED curing systems within its specified operating conditions.

 

A Better Troubleshooting Sequence

 

When curing quality becomes poor, use a systematic process.

 

Step 1 – Confirm the Defect

 

Identify exactly what has changed.

 

Is the problem:

 

Tackiness?

 

Poor adhesion?

 

Soft coating?

 

Weak bonding?

 

Uneven curing?

 

Do not start adjusting the machine before defining the problem.

 

Step 2 – Check Machine Settings

 

Confirm:

 

UV power

 

Conveyor speed

 

Exposure time

 

Working distance

 

Active UV modules

 

Step 3 – Measure UV Output

 

Use an appropriate UV measurement instrument to record:

 

Peak irradiance

 

Accumulated energy

 

Exposure duration

 

Step 4 – Compare with Historical Data

 

Compare the current measurement against a known-good production baseline.

 

Step 5 – Inspect the Equipment

 

If UV output has changed, investigate:

 

UV LED condition

 

Optical cleanliness

 

Cooling

 

Power system

 

Mechanical setup

 

Step 6 – Check the Material

 

If UV output remains normal, investigate ink, coating, adhesive and substrate variables.

 

Step 7 – Correct and Verify

 

After making a correction:

 

Measure again and test the finished product.

 

Do not assume the problem has been solved until it is verified.

 

Example: UV Printing Machine

 

A printing factory has used the same UV LED machine for months.

 

Suddenly, the printed ink becomes tacky.

 

Possible Reaction

 

Increase UV power immediately.

 

Better Reaction

 

First compare:

 

Current peak UV irradiance

 

Current accumulated UV energy

 

Current conveyor speed

 

against the historical baseline.

 

If peak irradiance is normal but accumulated energy is lower, the problem may be related to exposure time or conveyor speed rather than lamp output.

 

Example: UV Coating Line

 

A manufacturer notices reduced coating hardness.

 

The maintenance department suspects an aging UV LED module.

 

Before replacing it, the team measures the system.

 

If the UV reading improves substantially after cleaning the relevant optical surfaces, an expensive UV module replacement may not be necessary.

 

Measurement can therefore support better maintenance decisions.

 

Example: UV Adhesive Bonding

 

An electronics factory reports weaker bonding.

 

UV measurements are compared against the qualified production baseline.

 

If the curing conditions remain stable, engineers can investigate:

 

Adhesive storage

 

Dispensing volume

 

Bond-line thickness

 

Component cleanliness

 

Surface preparation

 

This avoids changing a stable UV curing process unnecessarily.

 

Why You Need a Known-Good Baseline

 

Imagine you measure your UV machine today for the first time.

 

You obtain a UV energy value.

 

Is it correct?

 

Maybe.

 

But without historical data, comparison is difficult.

 

The best time to establish a baseline is when production quality is good.

 

Record:

 

Machine ID:

UV wavelength:

UV power setting:

Conveyor speed:

Working distance:

Peak UV irradiance:

Accumulated UV energy:

Exposure duration:

Maximum temperature:

Product quality: PASS

 

Now you have a reference for future troubleshooting.

 

Don't Replace the UV LED Too Quickly

 

When curing quality drops, replacing the UV LED module may be expensive.

 

Before doing so, check:

 

Has measured UV output actually decreased?

 

Is the optical path clean?

 

Is cooling operating correctly?

 

Has the working distance changed?

 

Has conveyor speed changed?

 

Has exposure time changed?

 

Are all UV modules active?

 

Has the material changed?

 

Measurement helps maintenance teams make decisions based on evidence.

 

Don't Increase UV Power Blindly Either

 

Increasing UV power may appear to solve under-curing, but it can also hide the actual cause.

 

For example, the real problem may be:

 

Incorrect conveyor speed

 

Dirty optics

 

Wrong lamp distance

 

Changed material

 

A better approach is:

 

Measure → Identify Cause → Correct → Measure Again → Verify Quality

 

LS137 or LS136?

 

First identify the UV source technology.

 

For:

 

UV LED curing system

 

→ Consider Linshang LS137

 

For:

 

Traditional high-pressure mercury UV curing lamp

 

→ Consider Linshang LS136

 

The detector should be suitable for the spectral characteristics of the UV source.

 

Industries That Can Use LS137 for Troubleshooting

 

The LS137 can be relevant to:

 

UV printing

 

Packaging printing

 

Label printing

 

UV coating

 

Electronics manufacturing

 

PCB production

 

UV adhesive bonding

 

Optical manufacturing

 

Automated assembly

 

Industrial production lines

 

Potential users include:

 

Maintenance Engineers

 

Process Engineers

 

Production Engineers

 

QA/QC Personnel

 

Equipment Engineers

 

Turn Troubleshooting into Data

 

Without measurement, UV curing troubleshooting often sounds like this:

 

“Maybe the lamp is old.”

 

“Maybe we should increase the power.”

 

“Maybe the ink has a problem.”

 

With measurement data, the discussion becomes:

 

“Peak irradiance has changed.”

 

“UV energy dropped after the conveyor-speed increase.”

 

“UV output is still consistent with our baseline, so we should investigate the material.”

 

That is a much stronger way to troubleshoot an industrial process.

 

Looking for a UV LED Curing Tester in Malaysia?

 

MTM Precision supplies industrial testing and measurement instruments for manufacturing, engineering, maintenance and quality-control applications in Malaysia.

 

If your UV LED curing machine is not curing properly, provide us with:

 

UV wavelength

 

UV source type

 

Curing machine model

 

Application

 

Conveyor speed or exposure time

 

Expected UV intensity

 

We can assist you in determining whether the Linshang LS137 UV Energy Meter is suitable for troubleshooting your UV LED curing process.

 

Contact MTM Precision

 

MTM Precision Sdn. Bhd.

 

Showroom & Service Centre

 

No. 29-1 & 29-2, Jalan Bandar 18,

Pusat Bandar Puchong,

47160 Puchong, Selangor, Malaysia

 

🌐 Website: www.mtmpre.com.my

📧 Email: mtmpre@yahoo.com

📱 WhatsApp: +6016-660 7346

 

Contact MTM Precision for Linshang LS137 UV Energy Meter enquiries, technical information and quotation in Malaysia.


 

13 Aug 2026