Langry APT100 vs APT200 vs APT300 Which Anchor Pull-Out Tester Should You Choose? Malaysia

Langry APT100 vs APT200 vs APT300 – Which Anchor Pull-Out Tester Should You Choose? Malaysia   Langry Anchor Pull-Out Tester Selection Guide Malaysia   Choosing the correct anchor pull-out tester is not simply a matter of buying the model with the highest capacity.   The appropriate tester should be selected according to the required test load, anchor type, anchor size, test configuration and actual construction application.   Langry offers three main capacities in its APT Anchor Pull-Out Tester series:   Langry APT100 – 100kN / 10 Ton Class   Langry APT200 – 200kN / 20 Ton Class   Langry APT300 – 300kN / 30 Ton Class   For contractors, consultants, inspection companies, testing laboratories and QA/QC teams in Malaysia, understanding the difference between these three models can help avoid purchasing equipment that is either undersized or unnecessarily large for the intended application.   Langry APT100 vs APT200 vs APT300 at a Glance   ModelMaximum RangeApproximate CapacityAPT1000–100kN10 TonAPT2000–200kN20 TonAPT3000–300kN30 Ton   The main difference is the available measurement and loading capacity.   However, capacity alone should not determine the final selection.   What Is an Anchor Pull-Out Tester?   An anchor pull-out tester is used to apply controlled tensile force to an installed anchoring component.   Depending on the test configuration, applications may include suitable:   Anchor bolts   Expansion bolts   Mechanical anchors   Chemical anchors   Anchor rods   Threaded rods   Steel bars   Post-installed anchoring components   The tester allows the operator to monitor the applied tensile force and evaluate the installation according to the specified project test procedure.   Langry APT100 – 100kN / 10 Ton Class   The Langry APT100 provides a maximum measurement range of:   0–100kN   This corresponds to approximately a 10-ton class pull-out tester.   The APT100 can be considered where the anticipated test loads remain comfortably within the 100kN range.   Potential applications may include selected lighter anchor testing requirements and general construction inspection work.   When Should You Consider the APT100?   The APT100 may be appropriate when:   Required test loads are below 100kN   Most work involves lower-load anchors   Portability is an important consideration   Higher 200kN or 300kN capacity is unnecessary   The customer's normal testing scope is clearly defined   For users who know that their maximum required loads are relatively low, purchasing a larger system may provide little practical advantage.   Langry APT200 – 200kN / 20 Ton Class   The Langry APT200 provides a maximum measurement range of:   0–200kN   This corresponds to approximately a 20-ton class pull-out tester.   For many professional users, the APT200 represents a useful middle-capacity option.   It provides substantially more range than the APT100 while avoiding the need to move immediately to a 300kN system.   Why Is the APT200 a Practical Middle Option?   Contractors and testing companies may encounter different anchor sizes and project requirements over time.   A tester selected only for today's smallest application may become limiting when a larger project arrives.   The APT200 provides additional capacity for users handling a wider range of testing requirements.   Potential applications include:   Chemical anchor testing   Mechanical anchor testing   Expansion bolt testing   Anchor rod testing   Suitable steel bar pull-out testing   Façade anchor testing   Curtain wall anchor testing   Construction QA/QC   The actual suitability depends on the required test load and test arrangement.   Langry APT300 – 300kN / 30 Ton Class   The Langry APT300 provides a maximum measurement range of:   0–300kN   This corresponds to approximately a 30-ton class pull-out tester.   The APT300 is intended for applications requiring greater capacity than the APT100 or APT200 can provide.   It may be considered where higher tensile test loads are expected.   When Should You Consider the APT300?   The APT300 may be more appropriate when:   Required test loads can exceed 200kN   Larger anchoring systems are regularly tested   The company handles heavier-duty projects   A 200kN tester would provide insufficient capacity   Higher testing range is specifically required by the project   Buying a 300kN tester only because it is the largest model is not necessarily the best approach.   The tester should match the actual work.   Is a Higher-Capacity Pull-Out Tester Always Better?   No.   A larger-capacity tester can provide more available range, but several other factors should be considered.   These include:   Equipment size   Equipment weight   Site accessibility   Required adapters   Reaction setup   Expected test loads   Frequency of high-load testing   Portability requirements   Budget   The most suitable equipment is the one that correctly matches the user's testing requirements.   How Much Capacity Do You Actually Need?   Before purchasing an anchor pull-out tester, determine the maximum anticipated test load.   For example:   If your projects normally require testing well below 100kN, an APT100 may provide sufficient range.   If your projects can require loads above 100kN but remain below 200kN, the APT200 may provide greater flexibility.   If your work genuinely requires loads beyond 200kN, the APT300 should be considered.   Do not select the tester solely from anchor diameter.   Tester Capacity Is Not the Same as Anchor Test Load   This is an important distinction.   If you purchase an APT200, it does not mean every anchor should be tested to 200kN.   Likewise, buying an APT300 does not mean anchors should be loaded to 300kN.   The instrument rating indicates its available measurement range.   The actual test load is determined by factors such as:   Anchor specification   Design requirements   Anchor system   Base material   Project specification   Approved test method   Engineer or consultant requirements   Should You Leave Some Capacity Margin?   When selecting testing equipment, it can be useful to consider not only today's required load but also the range of projects the company expects to handle.   For example, if normal testing requirements are already close to the upper range of a 100kN tester, a 200kN model may offer more flexibility for future work.   However, this does not mean customers should automatically buy the largest available model.   Selection should remain application-based.   Which Model Is Best for Chemical Anchor Testing?   There is no single capacity that is correct for every chemical anchor.   Chemical anchor testing requirements depend on:   Threaded rod or rebar size   Anchor system   Embedment depth   Base material   Required proof load   Engineering specification   For lower test loads, the APT100 may be sufficient.   For users handling a wider range of projects, the APT200 may offer more flexibility.   Higher-load applications may require the APT300.   Which Model Is Best for Expansion Bolt Testing?   Again, the correct selection depends on the required test load rather than simply the fact that the anchor is an expansion bolt.   Before choosing a tester, determine:   Anchor diameter   Anchor type   Required test load   Substrate   Test configuration   For contractors working with multiple mechanical anchor sizes, having additional capacity can be useful.   Which Model Is Best for Rebar Pull-Out Testing?   For suitable post-installed steel bar testing applications, expected tensile load is particularly important.   The bar diameter alone is not sufficient to select the tester.   Consider:   Bar diameter   Steel properties   Embedment   Anchoring system   Required test load   Pulling connection   Reaction setup   Where the anticipated load can exceed 100kN, an APT100 would not provide sufficient range.   In such cases, an APT200 or APT300 may need to be considered.   Which Model Is Best for Curtain Wall and Façade Contractors?   Façade contractors may test different anchor types across different projects.   These may include:   Chemical anchors   Expansion anchors   Threaded rods   Mechanical anchors   Façade bracket fixings   Because project requirements can vary, some contractors may prefer the broader capacity of the APT200.   However, the final choice should still be based on actual anticipated test loads.   Which Model Is Best for Testing Laboratories?   Testing companies and inspection laboratories often serve multiple customers.   Their required test range may therefore be broader than that of a contractor working with only one anchor system.   A laboratory or inspection company should review:   Typical customer requirements   Historical test loads   Maximum expected test load   Future service scope   Portability requirements   A wider-capacity model may provide more flexibility if different project types are expected.   Which Model Is Best for Contractors?   A contractor should select equipment according to the normal project scope.   For example:   Mainly lighter anchor testing   Consider APT100 if the required loads remain within its range.   Mixed construction anchor testing   Consider APT200 where additional capacity and flexibility are useful.   Regular high-load anchor testing   Consider APT300 where the project requires capacity beyond 200kN.   APT100 vs APT200 – Which Should You Buy?   The key question is:   Can your expected testing requirement exceed 100kN?   If the answer is clearly no, APT100 may be sufficient.   If the answer is yes—or future projects may require higher loads—the APT200 provides up to 200kN capacity.   For companies that perform anchor testing as an ongoing service, this additional range can be useful.   APT200 vs APT300 – Which Should You Buy?   The key question becomes:   Do you realistically need more than 200kN?   If normal testing remains below 200kN, the APT200 may provide adequate capacity.   If projects require loads above 200kN, the APT300 should be considered.   There is little benefit in carrying additional capacity if it is never required.   Simple Langry APT Selection Guide   Your RequirementModel to ConsiderMaximum test requirement below 100kNAPT100Need more than 100kN but up to 200kNAPT200Need more than 200kN but up to 300kNAPT300Unsure of required test loadCheck project specification firstMultiple project typesReview maximum anticipated loadSpecial anchor configurationConfirm setup and accessories   This table is a general selection guide only.   Final equipment selection should be based on the actual test requirements.   Questions to Ask Before Buying an Anchor Pull-Out Tester   Before requesting a quotation, prepare the following information:   What are you testing?   Is it a chemical or mechanical anchor?   What is the anchor diameter?   What is the required proof load?   What is the maximum expected load?   What base material is involved?   How much anchor or thread is exposed?   What connection or adapter is required?   Is testing performed on site?   Is the test location difficult to access?   Providing this information makes model selection much easier.   Common Mistake: Selecting by “Ton” Only   Customers often ask:   “I need a 10-ton pull-out tester.”   or:   “Do you have a 20-ton anchor tester?”   Capacity is important, but it is only part of the selection process.   A proper selection should consider the complete test configuration.   For example, a tester may have sufficient force capacity but the required connection, access or reaction arrangement may still need to be addressed.   Why the APT200 Is Worth Considering   For users who do not want to be limited to 100kN but also do not regularly require 300kN, the Langry APT200 provides a practical middle range.   Its key specifications include:   0–200kN measurement range   Approximately 20-ton capacity   35mm cylinder centre hole   70mm cylinder stroke   M24 pull rod   M6–M22 converters   Up to 500 stored records   More than 200 hours continuous working time   EN ISO 7500-1 Class 1 accuracy classification   This makes the APT200 particularly relevant to professional contractors, QA/QC teams and testing companies requiring a versatile field pull-out tester.   Frequently Asked Questions   What is the difference between APT100, APT200 and APT300?   The primary difference is maximum measurement capacity: 100kN, 200kN and 300kN respectively.   Is APT200 a 20-ton pull-out tester?   Yes. Its 200kN maximum range corresponds to approximately 20.4 metric tonnes-force, so it is commonly described as a 20-ton class tester.   Is APT300 always better than APT200?   No. APT300 provides higher capacity, but the best model depends on the actual required test range and site application.   Is APT100 enough for anchor testing?   It can be sufficient where the maximum required test load remains within 100kN and the test configuration is suitable.   Which Langry model should I choose if I don't know the required load?   Check the project's test specification or obtain the required proof/test load from the responsible engineer before selecting the equipment.   Can one APT200 test both chemical and mechanical anchors?   It can be used for suitable testing applications involving different anchoring systems when the required load, adapters and test arrangement are compatible.   Should I choose the tester according to anchor diameter?   Not by diameter alone. Required load, connection method, base material, reaction setup and project requirements should also be considered.   Where can I buy Langry APT100, APT200 or APT300 in Malaysia?   MTM Precision Sdn. Bhd. supplies construction testing and anchor pull-out testing equipment in Malaysia and can assist with model selection according to the customer's application.   Langry Anchor Pull-Out Tester Supplier Malaysia   MTM Precision supplies professional testing and measurement equipment for construction, civil engineering, industrial and inspection applications.   For customers considering a Langry anchor pull-out tester, providing the anchor type, anchor diameter and required test load allows us to better identify whether the APT100, APT200 or APT300 is appropriate.   Contact MTM Precision   MTM Precision Sdn. Bhd.   Showroom & Service Centre   No. 29-1 & 29-2, Jalan Bandar 18, Pusat Bandar Puchong, 47160 Puchong, Selangor, Malaysia   馃寪 Website: www.mtmpre.com.my 馃摟 Email: mtmpre@yahoo.com 馃摫 WhatsApp: +6016-660 7346   For Langry APT100, APT200 and APT300 Anchor Pull-Out Tester Malaysia, quotations, model selection and construction testing equipment enquiries, contact MTM Precision.  

11 Aug 2026