Langry APT200 for Curtain Wall and Facade Anchor Pull-Out Testing Malaysia

Langry APT200 for Curtain Wall and Façade Anchor Pull-Out Testing Malaysia   Curtain Wall Anchor Pull-Out Tester Malaysia   The Langry APT200 Anchor Pull-Out Tester is a professional 200kN / 20-ton class hydraulic pull-out testing system suitable for on-site testing of anchors and anchoring components used in construction applications.   One important application is anchor pull-out testing for curtain wall and façade installation projects.   Modern façade systems depend on properly installed anchors, brackets and structural fixings to transfer loads from the façade system to the supporting building structure.   Where specified by the project engineer, consultant or approved inspection procedure, selected anchors may require on-site pull-out testing to verify their installed performance.   For façade contractors, curtain wall installers, QA/QC teams, consultants and testing companies in Malaysia, the Langry APT200 provides up to 200kN measurement capacity for suitable anchor testing applications.   Why Is Anchor Testing Important for Curtain Wall Projects?   Curtain wall and façade systems can involve many structural and non-structural connections.   These connections may support or transfer loads associated with:   Façade panels   Glass systems   Aluminium framing   Steel brackets   Supporting rails   Cladding systems   Secondary support structures   The reliability of the overall system depends partly on the quality of the anchoring connections.   An anchor that is incorrectly installed may not perform as intended even if the specified anchor product itself is suitable.   For this reason, anchor inspection and testing may form part of the project's quality assurance process.   What Is a Curtain Wall Anchor Pull-Out Test?   A curtain wall anchor pull-out test applies a controlled tensile force to a selected installed anchor or fixing.   The purpose is to evaluate the anchor under the specified test conditions.   Depending on the project requirements, the test may be used for:   Installation verification   Proof testing   Quality control   Site investigation   Comparative testing   Anchor system assessment   The required test load and acceptance criteria must be established by the applicable project specification or approved test method.   Langry APT200 Technical Specifications   SpecificationLangry APT200Measurement Range0–200kNApproximate Capacity20 TonCylinder Center Hole35mmCylinder Stroke70mmCylinder WeightApprox. 13kgCommon AnchorageΦ6–Φ25Pull RodM24ConverterM6–M22Data Storage500 RecordsContinuous Working Time>200 HoursAccuracy ClassificationEN ISO 7500-1 Class 1   The APT200 provides a useful balance between portable field operation and relatively high pull-out testing capacity.   Types of Façade Anchors That May Require Testing   Depending on the façade system and project design, testing may involve suitable:   Mechanical anchors   Expansion anchors   Chemical anchors   Anchor rods   Threaded rods   Steel anchoring elements   Post-installed fixings   The correct test configuration depends on the anchor type, geometry, required load and available access.   Chemical Anchors in Façade Installation   Chemical or bonded anchors may be used where threaded rods or other anchoring elements are fixed into concrete using an adhesive anchoring system.   Their installed performance may be influenced by:   Hole diameter   Hole depth   Hole cleaning   Adhesive installation   Adhesive mixing   Embedment depth   Curing time   Temperature   Concrete condition   Workmanship   Where required, pull-out testing can help verify selected completed installations.   Mechanical Anchors in Curtain Wall Projects   Mechanical anchors are also commonly used for façade brackets and supporting components.   Performance may depend on factors such as:   Correct drill diameter   Correct embedment   Installation torque   Expansion setting   Concrete condition   Edge distance   Anchor spacing   Installation workmanship   The appropriate installation and test requirements should follow the anchor manufacturer's instructions and project specification.   Typical Curtain Wall Anchor Pull-Out Test Procedure   A general site procedure may involve the following steps.   Step 1 – Identify the Test Anchor   Record the anchor location, anchor type and relevant project identification.   Step 2 – Confirm the Required Test Load   Determine the specified proof or test load before beginning.   Do not determine the test load based solely on the maximum capacity of the pull-out tester.   Step 3 – Inspect the Anchor   Check the anchor and surrounding substrate for visible damage, cracking or unusual installation conditions.   Step 4 – Select the Correct Adapter   Use a pulling connection suitable for the anchor geometry and test arrangement.   Step 5 – Position the Hydraulic Cylinder   Place the cylinder and reaction arrangement so that the pulling force is applied as axially as practical.   Step 6 – Check the Setup   Confirm that the pulling rod, adapter, hydraulic cylinder and reaction arrangement are secure.   Step 7 – Apply Load Gradually   Increase the tensile load in a controlled manner according to the approved test procedure.   Step 8 – Reach the Required Test Load   Monitor the digital force reading until the specified test level is reached.   Step 9 – Hold the Load if Required   Some project procedures require the proof load to be maintained for a specified period.   Step 10 – Observe the Anchor   Monitor for movement, cracking, deformation, slipping or other abnormal behaviour.   Step 11 – Release the Load Safely   Reduce the hydraulic pressure in a controlled manner after completing the test.   Step 12 – Record the Result   Document the applied load, observations and result according to the project requirements.   200kN Is Maximum Tester Capacity, Not the Curtain Wall Test Load   The Langry APT200 provides a maximum measurement range of:   0–200kN   This does not mean a façade anchor should automatically be tested to 200kN.   The actual test load may be significantly lower.   It should be determined according to:   Anchor specification   Façade design   Design load   Project requirements   Approved testing procedure   Engineer or consultant requirements   The 200kN figure represents the available measurement capacity of the tester.   Proof Testing for Façade Anchors   A proof test normally applies a predetermined load to an installed anchor to verify it against specified acceptance requirements.   The intention is generally not to destroy the anchor.   The test may include:   Controlled loading   Reaching a specified proof load   Holding the load   Monitoring movement or behaviour   Recording the result   Acceptance should be based on the project's defined criteria.   Destructive Anchor Testing   Some projects or engineering investigations may require testing to a failure criterion.   This is different from routine proof testing.   Possible failure modes may include:   Anchor pull-out   Concrete breakout   Bond failure   Anchor steel failure   Excessive displacement   Local concrete damage   Destructive testing should only be performed according to an appropriate engineering test plan and with suitable safety controls.   Common Causes of Façade Anchor Test Problems   Incorrect Anchor Installation   An incorrectly installed anchor may not develop the expected performance.   Poor Hole Cleaning   For bonded anchors, drilling dust and debris may affect the anchoring system if the required cleaning procedure is not followed.   Insufficient Embedment   Incorrect embedment depth can affect anchorage performance.   Incorrect Tightening   Some mechanical anchors require specific installation torque or setting procedures.   Insufficient Adhesive Curing   A chemical anchor should not be tested before the required curing conditions have been achieved.   Weak or Damaged Concrete   The condition of the substrate can significantly affect the test.   Incorrect Anchor Selection   An anchor should be suitable for the substrate, load and application.   Poor Workmanship   Installation quality can affect the final anchoring performance.   Anchor Testing for Glass Curtain Wall Installation   Glass curtain wall systems rely on supporting frames, brackets and connections to transfer loads back to the building structure.   Where post-installed anchors are used, project specifications may require selected anchors to undergo site testing.   The Langry APT200 can provide a portable method of applying and measuring tensile load for suitable testing arrangements.   This makes it relevant to:   High-rise buildings   Commercial buildings   Office towers   Shopping centres   Hotels   Hospitals   Institutional buildings   Mixed-use developments   Anchor Testing for Aluminium Façade Systems   Aluminium façade framing and supporting brackets may also depend on anchoring systems connected to concrete structural elements.   Pull-out testing may be specified to verify selected anchor installations before subsequent façade works proceed.   Anchor Testing for Cladding Systems   External cladding systems may use supporting rails, brackets and anchors.   Depending on the project design and specification, selected anchoring points may require verification.   Pull-out testing can form one part of this inspection process.   Why Façade Contractors Need Portable Pull-Out Testers   Façade installation can involve anchors across many locations and levels of a building.   A portable testing system allows qualified personnel to perform appropriate tests directly at the required location.   Potential advantages include:   On-site testing   Immediate force readings   Testing at selected installation locations   Reduced dependence on transporting specimens   Convenient project QA/QC   Digital test data recording   For contractors regularly handling façade works, having suitable testing equipment available can improve operational flexibility.   Importance of Test Location Identification   Large curtain wall projects may contain hundreds or thousands of anchors.   Good test records should therefore clearly identify each tested location.   Information may include:   Building name   Floor level   Grid reference   Elevation   Façade zone   Anchor number   Anchor type   Anchor diameter   Test date   Required test load   Maximum applied load   Result   Photographs may also be useful as part of the project documentation.   What Should Be Included in a Curtain Wall Anchor Test Report?   Depending on project requirements, a report may include:   Project information   Test date   Test location   Anchor identification   Anchor type   Anchor size   Base material   Installation details   Required test load   Applied load   Holding time   Observations   Visible movement   Substrate condition   Pass/fail result according to specified criteria   Tester identification   Operator information   The Langry APT series can store up to 500 measurement records, assisting with force data management.   Safety During Façade Anchor Pull-Out Testing   Pull-out testing can involve very high tensile forces.   The operator should establish a safe working area and consider:   Working-at-height requirements   Appropriate PPE   Equipment inspection   Secure test connections   Correct alignment   Stable reaction setup   Potential anchor failure direction   Falling-object risk   Restricted access around the test area   Personnel should never position themselves directly in the potential failure path of a highly loaded pulling assembly.   Why Choose Langry APT200 for Curtain Wall Anchor Testing?   The Langry APT200 provides:   0–200kN measurement range   Approximately 20-ton class capacity   Portable hydraulic loading   Digital force measurement   70mm cylinder stroke   35mm centre hole   Data storage for up to 500 records   Long operating time   Its capacity makes it suitable for many professional construction anchor testing requirements where a smaller-capacity tester may not provide sufficient range.   Langry APT100 vs APT200 vs APT300 for Façade Testing   ModelMaximum RangeApproximate CapacityAPT100100kN10 TonAPT200200kN20 TonAPT300300kN30 Ton   The correct tester should be selected according to the anticipated test load and test configuration.   A larger tester is not automatically better if the application does not require the additional capacity.   Who May Use the Langry APT200?   Potential users include:   Curtain wall contractors   Façade contractors   Main contractors   Structural contractors   Anchor installation contractors   QA/QC teams   Engineering consultants   Building inspection companies   Testing laboratories   Civil engineering contractors   Infrastructure contractors   Frequently Asked Questions   Can the Langry APT200 test curtain wall anchors?   Yes. The Langry APT series is intended for suitable anchor pull-out testing applications, including anchoring associated with glass curtain wall installations.   What is the maximum range of the APT200?   The APT200 provides a maximum measurement range of 200kN, approximately a 20-ton class capacity.   Should curtain wall anchors be tested to 200kN?   Not automatically. The required test load must follow the façade design, anchor specification, project requirements and approved test method.   Can it test chemical anchors used for façade brackets?   It can be used in suitable chemical anchor pull-out testing arrangements when the connection, load range and test setup are appropriate.   Can it test expansion anchors?   Suitable expansion bolts and mechanical anchors are among the anchoring applications for this type of pull-out testing equipment.   Is façade anchor pull-out testing destructive?   Not always. Proof testing normally applies a specified test load without intentionally taking the anchor to failure. Destructive testing has a different objective.   Can test data be stored?   The Langry APT series supports storage of up to 500 measurement records.   Where can I buy a curtain wall anchor pull-out tester in Malaysia?   MTM Precision Sdn. Bhd. supplies Langry anchor pull-out testing equipment and construction testing instruments in Malaysia.   Curtain Wall and Façade Testing Equipment Supplier Malaysia   Before selecting a pull-out tester for a façade project, users should identify:   Anchor type   Anchor diameter   Required proof load   Maximum anticipated test load   Available anchor connection   Test location   Access restrictions   Reaction arrangement   Project testing procedure   MTM Precision can assist customers in selecting a suitable Langry pull-out tester according to their testing application.   Contact MTM Precision   MTM Precision Sdn. Bhd.   Showroom & Service Centre   No. 29-1 & 29-2, Jalan Bandar 18, Pusat Bandar Puchong, 47160 Puchong, Selangor, Malaysia   馃寪 Website: www.mtmpre.com.my 馃摟 Email: mtmpre@yahoo.com 馃摫 WhatsApp: +6016-660 7346   For Langry APT200 Curtain Wall and Façade Anchor Pull-Out Tester Malaysia, construction testing equipment and anchor testing enquiries, contact MTM Precision.  

11 Aug 2026