Anchor Pull-Out Tester for M12, M16 & M20 Chemical Anchors Malaysia

Anchor Pull-Out Tester for M12, M16 & M20 Chemical Anchors Malaysia

 

What Pull-Out Tester Do I Need for M12, M16 or M20 Chemical Anchors?

 

Customers looking for an anchor pull-out tester often start with the anchor size:

 

“I need to test M12 chemical anchors.”

 

“Can this tester test M16?”

 

“What tonnage do I need for M20 anchors?”

 

Anchor size is important because it affects the mechanical connection between the anchor and the pull-out tester.

 

However, M12, M16 or M20 alone does not determine the required tester capacity.

 

To select the correct anchor pull-out tester, you should confirm at least:

 

Anchor Size + Required Test Load + Test Application + Connection Configuration

 

For suitable applications requiring up to 200kN measurement range, the Langry APT200 Anchor Pull-Out Tester is one option for professional chemical anchor testing in Malaysia.

 

Quick Answer: M12, M16 and M20

 

A simple equipment-selection approach is:

 

Anchor SizeCan Tester Be Selected from Size Alone?What You Must ConfirmM12NoRequired test load + connectionM16NoRequired test load + connectionM20NoRequired test load + connection

 

Do not automatically assume:

 

M12 = 10 Ton

 

M16 = 20 Ton

 

M20 = 30 Ton

 

There is no universal relationship like this.

 

Why Anchor Diameter Does Not Determine Test Load

 

Consider two M16 chemical anchors.

 

They may have the same nominal threaded-rod diameter but different:

 

Chemical anchoring systems

 

Embedment depths

 

Concrete conditions

 

Design loads

 

Installation configurations

 

Project requirements

 

One project may specify a relatively modest proof load.

 

Another M16 installation may have a substantially different requirement.

 

Therefore:

 

Anchor Diameter ≠ Required Pull-Out Force

 

M12 Chemical Anchor Pull-Out Testing

 

M12 threaded rods are commonly encountered in many construction fixing applications.

 

Potential applications can include:

 

Steel brackets

 

M&E supports

 

Façade components

 

Equipment supports

 

General structural fixings

 

Before testing an M12 chemical anchor, confirm:

 

Exact anchor/thread size

 

Exposed thread length

 

Chemical anchor system

 

Required test load

 

Test objective

 

Test procedure

 

Do not select tester capacity solely because the rod is M12.

 

M16 Chemical Anchor Pull-Out Testing

 

M16 is another commonly encountered size in construction anchoring.

 

Applications may include:

 

Façade brackets

 

Structural steelwork

 

Heavy supports

 

Retrofit installations

 

Equipment anchoring

 

When a customer asks:

 

“Can Langry APT200 test M16?”

 

the answer requires more than the diameter.

 

We need to know:

 

What load does the project require?

 

and:

 

Can the test connection be configured correctly?

 

M20 Chemical Anchor Pull-Out Testing

 

M20 anchors may be used in heavier anchoring applications.

 

However, the same principle applies.

 

Do not assume that every M20 anchor requires 200kN or 300kN testing.

 

The correct load should come from the approved engineering or project requirements.

 

Before testing, check:

 

Required force

 

Thread condition

 

Exposed length

 

Embedment

 

Adapter arrangement

 

Reaction setup

 

What About M6, M8, M10 and M22?

 

The Langry APT200 configuration includes converters covering M6–M22 according to the manufacturer's stated configuration.

 

However, nominal converter availability alone does not establish that every anchor installation can automatically be tested.

 

You must still consider:

 

Required force

 

Thread engagement

 

Exposed length

 

Surrounding clearance

 

Test geometry

 

Reaction arrangement

 

For unusual installations, send photographs and dimensions before testing or purchasing equipment.

 

Langry APT200 Pulling Configuration

 

The Langry APT200 includes:

 

Pull Rod: M24

 

Converters: M6–M22

 

This provides flexibility for a range of supported threaded anchor configurations.

 

For M12, M16 and M20 applications, the actual connection should still be checked before testing.

 

Why Exposed Thread Length Matters

 

Imagine an M16 chemical anchor.

 

The customer confirms:

 

“Yes, it is M16.”

 

But only a very short section of thread remains exposed above the bracket.

 

The adapter may not have sufficient engagement.

 

Therefore, before going to site, ask:

 

How much usable thread is exposed?

 

A photograph with dimensions can be very useful.

 

Existing Nuts and Brackets Can Affect Testing

 

Some installed chemical anchors already contain:

 

Nuts

 

Washers

 

Steel plates

 

Façade brackets

 

Structural brackets

 

These components can affect how the pull-out tester is connected.

 

Do not assume the test setup from anchor diameter alone.

 

Check the Area Around the Anchor

 

The hydraulic cylinder needs physical clearance.

 

Potential obstructions include:

 

Nearby anchors

 

Steel plates

 

Concrete upstands

 

Walls

 

Façade profiles

 

Machinery bases

 

For complicated locations, send MTM Precision a photograph before purchasing or mobilising equipment.

 

How Do I Choose Tester Capacity for M12?

 

First ask:

 

What is the maximum required test load?

 

For example, if an approved M12 anchor test requires a load well within 100kN, a 100kN-class tester may potentially provide sufficient capacity, subject to the complete testing requirements.

 

If the required load exceeds 100kN, a higher-range model should be considered.

 

The anchor being M12 does not determine this by itself.

 

How Do I Choose Tester Capacity for M16?

 

The same process applies.

 

If the required load is:

 

Below or within 100kN

 

APT100 may potentially be considered.

 

If the requirement is:

 

Above 100kN but within 200kN

 

APT200 may be considered.

 

The exact selection should account for the test method and connection.

 

How Do I Choose Tester Capacity for M20?

 

Again, use the actual required load.

 

If the required test exceeds the APT200's maximum range, a higher-capacity model such as APT300 may need to be considered.

 

Do not buy APT300 simply because the anchor says M20.

 

Langry APT100 vs APT200 vs APT300

 

ModelMaximum Measurement RangeApproximate CapacityAPT100100kN10 TonAPT200200kN20 TonAPT300300kN30 Ton

 

The best model depends primarily on the required test range and actual test configuration.

 

Example 1 – M12 Anchor, Required Load 45kN

 

Suppose the project information is:

 

Anchor: M12 Chemical Anchor

 

Required Proof Load: 45kN

 

The first conclusion is:

 

A tester must be suitable for at least the required testing range.

 

Then check:

 

Adapter compatibility

 

Exposed thread

 

Reaction setup

 

Project procedure

 

There is no reason to assume 200kN is required simply because APT200 is available.

 

Example 2 – M16 Anchor, Required Load 120kN

 

Suppose:

 

Anchor: M16

 

Required Test Load: 120kN

 

A 100kN tester does not provide sufficient range for a 120kN requirement.

 

A 200kN-class system such as the Langry APT200 may therefore be considered, subject to the complete test configuration.

 

Example 3 – M20 Anchor, Required Load 180kN

 

Suppose:

 

Anchor: M20

 

Required Test Load: 180kN

 

The requirement is within the APT200's 200kN measurement range.

 

The next questions are:

 

Is the connection suitable?

 

Is the reaction arrangement appropriate?

 

Is there sufficient clearance?

 

Does the approved procedure require any additional measurement?

 

Capacity alone does not complete equipment selection.

 

Example 4 – M16 Anchor, Required Load 220kN

 

Suppose:

 

Anchor: M16

 

Required Test Load: 220kN

 

The APT200 has a maximum range of 200kN.

 

Therefore, it does not provide sufficient measurement range for a 220kN requirement.

 

A higher-capacity tester such as the APT300 should be evaluated.

 

Notice that this is still an M16 anchor.

 

This clearly demonstrates why anchor diameter and tester capacity are not directly interchangeable.

 

Chemical Anchor Type Also Matters

 

Different chemical anchoring systems may have different:

 

Installation requirements

 

Hole dimensions

 

Embedment requirements

 

Curing conditions

 

Approved applications

 

Always follow the relevant anchor system requirements.

 

Concrete Condition Matters

 

The base material forms part of the anchoring system.

 

Testing behaviour can be influenced by:

 

Concrete condition

 

Cracking

 

Local defects

 

Edge location

 

Installation quality

 

The test result should therefore be interpreted within the actual project context.

 

Chemical Anchor Curing Before Testing

 

Before testing M12, M16 or M20 chemical anchors, confirm that the applicable curing requirement has been achieved.

 

Do not test simply because:

 

“The resin looks dry.”

 

Use the approved chemical anchor installation information and project requirements.

 

Proof Test or Failure Test?

 

Before selecting equipment, clarify the test objective.

 

Proof Load Test

 

The anchor is tested to a predetermined load according to the approved procedure without intentionally loading it to ultimate failure.

 

Ultimate / Failure Test

 

The test may continue toward a defined failure condition according to the applicable test method.

 

This distinction can affect equipment selection, site preparation and safety controls.

 

Common Mistake: Asking Only for “20 Ton”

 

Customers sometimes request:

 

“Give me one 20-ton pull-out tester.”

 

A better enquiry is:

 

“We test M16 chemical anchors. Maximum required test load is 135kN.”

 

This gives the supplier useful engineering information for equipment selection.

 

What Information Should You Send MTM Precision?

 

For faster model selection, send:

 

1. Anchor Size

 

Example: M16.

 

2. Anchor Type

 

Example: chemical anchor with threaded rod.

 

3. Required Test Load

 

Example: 120kN.

 

4. Exposed Thread Length

 

Provide dimensions if possible.

 

5. Application

 

Example: façade bracket.

 

6. Photograph

 

Especially useful for unusual installations.

 

With this information, equipment selection becomes much easier.

 

Langry APT200 Key Specifications

 

For suitable M12, M16, M20 and other supported anchor configurations, the APT200 provides:

 

SpecificationLangry APT200Measurement Range0–200kNApproximate Capacity20 TonCylinder Centre Hole35mmCylinder Stroke70mmCommon AnchorageΦ6–Φ25Pull RodM24ConverterM6–M22Data Storage500 RecordsAccuracy ClassificationEN ISO 7500-1 Class 1

 

Actual suitability should be confirmed for each application.

 

Who Typically Needs This Equipment?

 

Potential users include:

 

Anchor installation contractors

 

Façade contractors

 

Structural steel contractors

 

Main contractors

 

QA/QC teams

 

M&E contractors

 

Inspection companies

 

Testing laboratories

 

Companies working across many anchor sizes may benefit from equipment that supports multiple adapter configurations.

 

Frequently Asked Questions

 

Can Langry APT200 test M12 chemical anchors?

 

Potentially yes, for suitable configurations within the equipment's range. Confirm the required test load, thread engagement and test setup.

 

Can APT200 test M16 anchors?

 

M16 can fall within supported converter configurations, but the actual test load and connection must still be confirmed.

 

Can APT200 test M20 anchors?

 

Potentially yes for suitable configurations within the 200kN range. Confirm the complete test setup before testing.

 

Does M20 automatically require a 20-ton tester?

 

No. Anchor size alone does not determine tester capacity.

 

Does M16 automatically require 100kN?

 

No. The required load comes from the project requirements.

 

What happens if my required load is 220kN?

 

A 200kN tester does not provide sufficient range. A higher-capacity model should be considered.

 

What if I do not know the required load?

 

Obtain it from the appropriate project engineer, consultant or approved project documentation before selecting equipment.

 

Should I send a photo before buying?

 

For unusual installations, yes. A photograph together with dimensions can help identify connection and clearance issues.

 

Where can I buy M12, M16 and M20 chemical anchor pull-out testing equipment in Malaysia?

 

Contact MTM Precision Sdn. Bhd. for Langry APT-series model selection and quotation in Malaysia.

 

M12, M16 & M20 Chemical Anchor Pull-Out Tester Supplier Malaysia

 

MTM Precision supplies professional construction and civil engineering testing equipment for anchor testing applications throughout Malaysia.

 

Instead of sending only:

 

“Need pull-out tester price.”

 

send us:

 

Anchor Size + Anchor Type + Required Test Load + Application + Photo

 

For example:

 

M16 Chemical Anchor + 120kN + Curtain Wall Bracket + Site Photo

 

This allows us to recommend the appropriate Langry capacity and configuration more accurately.

 

Contact MTM Precision

 

MTM Precision Sdn. Bhd.

 

Showroom & Service Centre

 

No. 29-1 & 29-2, Jalan Bandar 18,

Pusat Bandar Puchong,

47160 Puchong, Selangor, Malaysia

 

🌐 Website: www.mtmpre.com.my

📧 Email: mtmpre@yahoo.com

📱 WhatsApp: +6016-660 7346

 

For M12, M16 & M20 Chemical Anchor Pull-Out Tester Malaysia, Langry APT100, APT200 and APT300 model selection, current quotation and professional construction testing equipment enquiries, contact MTM Precision.


 

12 Aug 2026