Linshang LS173 Colorimeter for Furniture and Wood Coating Color Quality Control Malaysia
Linshang LS173 Colorimeter for Furniture and Wood Coating Color Quality Control Malaysia
Color consistency can be an important quality requirement in furniture manufacturing, particularly for painted, coated and finished components that need to maintain a uniform appearance across the same product range.
A cabinet door, furniture panel or coated component may appear acceptable when inspected individually, yet a color difference can become much more obvious when several pieces are assembled or installed next to each other.
The Linshang LS173 Portable Colorimeter provides furniture manufacturers and quality control teams with an objective method for measuring suitable surface colors and comparing production samples against an approved reference.
For furniture and manufacturing companies in Malaysia, this can support incoming inspection, production QC, supplier quality control and finished product inspection.
Why Is Color Consistency Important in Furniture?
Furniture products often consist of several components produced at different times.
For example:
Panel A → Production Batch 1
Panel B → Production Batch 2
Door → Production Batch 3
Drawer Front → Production Batch 4
Each component may appear acceptable individually.
After assembly, however, differences between the components can become noticeable.
This is one reason why maintaining batch-to-batch color consistency can be important.
What Can Cause Furniture Color Variation?
Possible causes include:
Coating batch differences
Paint formulation
Pigment variation
Substrate differences
Application conditions
Curing conditions
Supplier variation
Production parameters
Surface preparation
Different production batches
Natural materials such as wood may also have inherent variation.
Therefore, the suitability of instrumental measurement and the interpretation of results should always be considered according to the actual material and surface.
Visual Inspection vs Color Measurement
Visual inspection remains important for furniture because customers evaluate the complete appearance of the finished product.
However, human color judgement can be affected by:
Lighting conditions
Viewing angle
Surrounding colors
Inspector experience
Eye fatigue
Individual perception
The LS173 can provide numerical color information as an additional QC reference.
Rather than replacing visual inspection, instrumental measurement can complement it.
Establishing an Approved Master Sample
For repeat manufacturing, companies can establish an approved reference sample.
This might be:
Customer-approved panel
Golden sample
Standard painted component
Approved coated sample
Production reference
Master color sample
Future production samples can then be compared against this reference.
A simple process may be:
Approved Master → Measure
Production Sample → Measure
Compare → Review Color Difference → QC Decision
Delta E for Furniture Color Comparison
Delta E (ΔE) is commonly used to represent the measured difference between two colors.
Generally:
Lower ΔE = smaller measured color difference
Higher ΔE = greater measured color difference
For suitable furniture and coating applications, this can provide QC teams with a more objective method of comparing samples.
However, the acceptable Delta E tolerance should be established according to the product, surface, customer requirements and internal QC specifications.
There is no universal Delta E acceptance limit suitable for every furniture material.
Painted Furniture Components
Painted furniture provides a straightforward example of where color consistency may matter.
Suitable applications may include:
Cabinet doors
Furniture panels
Shelving
Painted wooden components
MDF panels
Manufactured furniture parts
If components from different production batches are assembled into the same finished product, visible color differences may result in rejection.
Periodic color measurement can help monitor consistency.
Coated Panels and Components
Furniture manufacturers may also use coated or laminated components.
When suitable for instrumental measurement, the LS173 can help compare samples against an approved master.
This may be useful for both incoming supplier inspection and internal production QC.
Incoming Quality Control
Furniture manufacturers frequently purchase panels, painted parts or other finished components from external suppliers.
Incoming inspection can include:
Receive Material → Visual Inspection → Color Measurement → Compare Against Master → Accept / Hold / Investigate
Detecting a color issue before the component enters assembly can help avoid more expensive rework later.
Production Quality Control
Color measurement can also be performed during production.
For example:
First-Off Sample → Measure
Mid-Batch Sample → Measure
Final Sample → Measure
If measurements begin moving away from the approved reference, the production team can investigate before completing the entire batch.
This can be particularly useful for long production runs.
Final Assembly Color Matching
Some color differences are most noticeable only after components are assembled.
For example:
Cabinet Door + Side Panel + Drawer Front
If all three parts are intended to have a uniform appearance, differences between them may become obvious when viewed together.
Color measurement earlier in the production process can help identify potential mismatches before final assembly.
Supplier-to-Supplier Comparison
Furniture manufacturers may purchase similar components from several suppliers.
Instead of comparing Supplier A directly with Supplier B, both can be evaluated against the same approved reference:
Master → Supplier A
Master → Supplier B
Master → Supplier C
This provides a more consistent basis for supplier quality evaluation.
Color and Gloss Are Different
A common issue with surface appearance is that two samples can have similar colors but different gloss levels.
A colorimeter evaluates color characteristics and color differences.
A gloss meter evaluates surface gloss.
Therefore:
Similar Color + Different Gloss = Visually Different Appearance
For furniture manufacturers with strict appearance requirements, both measurements may be relevant.
D/8 Measurement Geometry
The Linshang LS173 uses D/8 optical geometry, referring to diffuse illumination with an 8-degree viewing geometry.
Controlled optical measurement helps provide a more standardized method for evaluating suitable surfaces compared with uncontrolled visual inspection alone.
This can improve repeatability between operators and production batches.
Be Careful with Natural Wood
Natural wood can have substantial variations in:
Grain
Texture
Color
Pattern
Surface structure
Therefore, measuring natural wood should not automatically be treated in the same way as measuring a uniform painted panel.
Multiple measurement locations and an appropriate inspection procedure may be necessary depending on the application.
The QC team should consider the natural variability of the material when interpreting results.
Why Multiple Measurements May Be Useful
For non-uniform surfaces, a single measurement may not represent the entire product.
A company may establish a procedure such as:
Point A → Measure
Point B → Measure
Point C → Measure
The measurement method should be consistent between the approved reference and production samples.
This is especially important for surfaces with natural or process-related variation.
Reduce Rework Before Assembly
Discovering a color mismatch after furniture has been assembled can create additional costs.
The product may need to be:
Disassembled
Refinished
Repainted
Replaced
Sorted
Reworked
Earlier color inspection can help identify questionable components before they reach final assembly.
Who Can Use the Linshang LS173?
The LS173 may be considered by:
Furniture manufacturers
Cabinet manufacturers
Panel manufacturers
Coating companies
Painted component suppliers
QA departments
QC departments
Supplier quality teams
Production engineers
Incoming inspection personnel
It is particularly relevant for suitable surfaces where repeatable color comparison against an approved standard is required.
Building a Furniture Color QC Procedure
A documented procedure may include:
Approved master sample
Measurement location
Number of measurement points
Sample orientation
Required color parameters
Acceptance criteria
Inspection frequency
Visual inspection requirements
Measurement records
Action for non-conforming products
The instrument works best as part of a consistent quality control process.
Linshang LS173 for Furniture Color Measurement Malaysia
MTM Precision supplies industrial testing and measurement instruments for manufacturing, engineering and quality control applications throughout Malaysia.
If your company needs a portable colorimeter for furniture color inspection, painted panel comparison, coating color QC, Delta E measurement or batch color consistency, contact MTM Precision to discuss your application.
Contact MTM Precision
MTM Precision Sdn. Bhd.
Showroom & Service Centre
No. 29-1 & 29-2, Jalan Bandar 18,
Pusat Bandar Puchong,
47160 Puchong, Selangor, Malaysia
🌐 Website: www.mtmpre.com.my
📧 Email: mtmpre@yahoo.com
📱 WhatsApp: +6016-660 7346
Looking for a Linshang LS173 Portable Colorimeter for furniture and wood coating color quality control in Malaysia? Contact MTM Precision for quotation, product information and application enquiries.
12 Aug 2026