Linshang LS173 Colorimeter for Electronics and Electrical Product Color Inspection Malaysia
Linshang LS173 Colorimeter for Electronics and Electrical Product Color Inspection Malaysia
Color consistency can be an important quality requirement for electrical and electronic products, particularly when multiple plastic housings, buttons, covers, panels or accessories are assembled into the same finished product.
A component may look acceptable when inspected individually, but a shade difference can become obvious once it is installed next to another component.
The Linshang LS173 Portable Colorimeter provides manufacturers and quality control teams with an objective method for measuring suitable product colors and comparing samples against an approved reference.
For electronics and electrical manufacturers in Malaysia, portable color measurement can support IQC, IPQC, OQC, supplier comparison and batch color consistency control.
Why Does Color Matter for Electrical and Electronic Products?
Product appearance influences how customers perceive manufacturing quality.
Consider a product consisting of:
Main Housing + Front Panel + Button + Battery Cover + Accessory
If all components are intended to be the same black, white, grey or another specified color, differences between them can make the finished product look inconsistent.
This can happen even when every component meets its dimensional and functional requirements.
Common Color Problems
Electrical and electronic manufacturers may encounter issues such as:
Plastic housing shade variation
Different colors between molded parts
Supplier-to-supplier differences
Batch-to-batch color changes
Painted enclosure color variation
Button and housing mismatch
Cover and body mismatch
Packaging color variation
These problems can become especially noticeable when components are assembled side by side.
Why Can Plastic Housings Change Color?
Plastic components can vary because of:
Resin batches
Pigment concentration
Masterbatch
Mixing ratios
Processing temperature
Injection molding parameters
Raw material suppliers
Recycled material content
Production conditions
Therefore, using the same nominal color specification does not always guarantee identical finished appearance.
Establish a Golden Sample
A useful color QC process begins with an approved reference.
This may be called:
Golden sample
Master sample
Customer-approved sample
Reference component
Approved production part
Future components can then be measured against the same master.
For example:
Golden Sample → Supplier A Housing
Golden Sample → Supplier B Housing
Golden Sample → Current Production Batch
This provides a common reference for comparison.
Delta E for Electronic Component QC
Delta E (ΔE) represents the measured difference between two colors.
In general:
Lower ΔE = smaller color difference
Higher ΔE = greater color difference
This allows QC personnel to quantify color difference rather than relying entirely on descriptions such as:
“Almost the same black.”
“Slightly more grey.”
“A little yellowish.”
“The new batch looks different.”
The acceptable Delta E tolerance should be established according to the company's actual product and customer requirements.
Incoming Quality Control – IQC
Electronics manufacturers often purchase molded parts and other components from external suppliers.
The LS173 can support incoming color inspection before the components enter assembly.
A possible workflow is:
Receive Components → Sampling → Visual Inspection → LS173 Measurement → Compare Against Golden Sample → Release / Hold
This can help identify questionable components before additional manufacturing costs are added.
Supplier A vs Supplier B
Multiple sourcing is common in manufacturing.
Suppose two injection molding suppliers produce the same white plastic enclosure.
Both use the same drawing and color specification, but their finished components appear slightly different.
Instead of deciding only by eye:
Golden Sample → Measure Supplier A
Golden Sample → Measure Supplier B
Both suppliers are evaluated against the same approved reference.
This can improve supplier quality discussions.
First-Off Production Inspection
Color measurement can also be incorporated into first-off approval.
Before mass production begins:
Machine Setup → First Sample → Visual Check → Color Measurement → Compare → Production Approval
If the first sample does not meet the established requirements, adjustments can be made before producing a large quantity.
In-Process Quality Control – IPQC
Even when the first sample passes, color may change during a long production run.
Periodic measurements can be performed:
Start → Measure
Mid-Production → Measure
Later Production → Measure
Final Sample → Measure
This can help identify color drift earlier.
Outgoing Quality Control – OQC
Before finished products are shipped, the color of suitable visible components can be checked again.
For products with strict appearance requirements, this adds another level of final quality assurance.
The LS173 can complement visual inspection rather than replace it.
Black Plastic Is Not Always the Same Black
Black is common in electrical and electronic products, but different black plastic components may still have noticeably different appearances.
For example:
Main Housing → Black A
Battery Cover → Black B
Button → Black C
When viewed separately, the differences may appear small.
Once assembled, the mismatch can become more obvious.
Objective color comparison can help manufacturers investigate these differences.
White Plastic Can Also Be Challenging
White components can show subtle differences in tone.
One sample may appear:
Warmer
Cooler
More yellowish
More bluish
Slightly darker
Visual judgement may vary between inspectors.
Instrumental measurement provides additional numerical information when comparing the components.
Painted Electrical Enclosures
The LS173 can also be considered for suitable painted or coated electrical enclosures.
Examples may include:
Control panels
Equipment housings
Electrical cabinets
Metal covers
Industrial enclosures
Where appearance specifications are important, color measurement can complement other QC checks.
Colorimeter vs Gloss Meter
Two black plastic components can have similar colors but still look different because their gloss levels are not the same.
A colorimeter measures color characteristics and color differences.
A gloss meter evaluates surface gloss.
Therefore, if the problem is:
“These two parts have similar colors but one looks shinier,”
gloss may also need to be evaluated.
Colorimeter vs Coating Thickness Gauge
For painted electrical enclosures, color and coating thickness are also separate parameters.
A coating thickness gauge checks the thickness of the applied coating.
A colorimeter evaluates color.
Depending on the specification, both may form part of the QC process.
D/8 Measurement Geometry
The Linshang LS173 uses D/8 optical geometry, referring to diffuse illumination with an 8-degree viewing geometry.
Controlled optical measurement provides a standardized method for evaluating suitable sample colors.
This can improve repeatability when different operators, shifts or suppliers are involved.
Portable Measurement for Factory QC
Because the LS173 is portable, it can be used at different inspection points, such as:
Incoming QC
Production areas
Assembly lines
QC rooms
Supplier facilities
Finished goods inspection
This makes it practical for manufacturers that need color measurement outside a dedicated laboratory.
Reduce Assembly Problems
Detecting a color mismatch before assembly is preferable to discovering it after a finished product has been built.
Once incorrect components enter assembly, the company may face:
Sorting
Disassembly
Rework
Component replacement
Production delays
Customer rejection
Earlier color inspection can help reduce this risk.
Building an Electronics Color QC Procedure
A company can establish a procedure covering:
Golden sample
Measurement position
Sample orientation
Number of measurements
Inspection frequency
Delta E or other criteria
Supplier inspection
Production inspection
OQC inspection
Record keeping
Non-conformance action
A repeatable procedure is essential when measurement results need to remain consistent across departments and production periods.
Who Can Use the Linshang LS173?
The LS173 may be considered by:
Electronics manufacturers
Electrical product manufacturers
Plastic injection molding companies
Electrical enclosure manufacturers
Appliance manufacturers
Contract manufacturers
QA and QC departments
Supplier quality engineers
Production engineers
Incoming inspection teams
It is particularly useful when suitable colored components need to be compared objectively against an approved reference.
Linshang LS173 for Electronics Color Inspection Malaysia
MTM Precision supplies industrial testing and measurement instruments for manufacturing, engineering and quality control applications throughout Malaysia.
If your company needs a portable colorimeter for plastic housing color inspection, electrical enclosure QC, Delta E measurement, supplier comparison or batch color consistency, contact MTM Precision to discuss your application.
Contact MTM Precision
MTM Precision Sdn. Bhd.
Showroom & Service Centre
No. 29-1 & 29-2, Jalan Bandar 18,
Pusat Bandar Puchong,
47160 Puchong, Selangor, Malaysia
🌐 Website: www.mtmpre.com.my
📧 Email: mtmpre@yahoo.com
📱 WhatsApp: +6016-660 7346
Looking for a Linshang LS173 Portable Colorimeter for electronics and electrical product color inspection in Malaysia? Contact MTM Precision for quotation, product information and application enquiries.
12 Aug 2026