UV Energy Measurement for UV LED Coating Lines – Linshang LS137 Malaysia

UV Energy Measurement for UV LED Coating Lines – Linshang LS137 Malaysia

 

UV LED coating offers manufacturers a fast and efficient way to cure coatings on plastics, metals, electronic components, printed materials and other industrial products.

 

However, a UV coating does not become properly cured simply because it passes underneath a UV LED lamp.

 

The final coating performance can depend on the actual UV exposure received by the surface.

 

If UV irradiance, accumulated UV energy, conveyor speed or working distance changes, coating quality may also change.

 

The Linshang LS137 UV Energy Meter provides a practical way to measure UV LED curing conditions and establish measurable process data for production and quality control.

 

Why UV Measurement Matters in Coating Production

 

A coating may look acceptable immediately after curing but still fail later performance tests.

 

Depending on the coating system, insufficient or inconsistent curing may contribute to:

 

Poor surface hardness

 

Weak adhesion

 

Easy scratching

 

Tacky surfaces

 

Poor wear resistance

 

Inconsistent gloss

 

Poor chemical resistance

 

Surface marking

 

Increased rejection

 

Reduced product durability

 

When these problems occur, the coating material is often blamed first.

 

But the UV curing process should also be checked.

 

What Determines UV Coating Cure?

 

Several variables can influence UV coating performance:

 

UV wavelength

 

UV irradiance

 

Accumulated UV energy

 

Exposure time

 

Conveyor speed

 

UV lamp distance

 

Coating formulation

 

Coating thickness

 

Substrate

 

Process temperature

 

This means UV curing should be treated as a controlled process rather than simply an ON/OFF machine function.

 

What Can Linshang LS137 Measure?

 

The Linshang LS137 provides several measurements useful for UV LED coating applications:

 

UV Energy

 

UV Irradiance

 

Peak UV Irradiance

 

Measurement Duration

 

Temperature

 

Maximum Temperature

 

These parameters can be recorded together with coating-quality results to create a production baseline.

 

UV Irradiance vs UV Energy

 

For coating applications, understanding the difference is important.

 

UV Irradiance

 

UV irradiance indicates how strong the UV radiation is at a particular moment.

 

It is commonly expressed in:

 

mW/cm²

 

UV Energy

 

UV energy indicates the accumulated UV exposure received during the curing cycle.

 

It is commonly expressed in:

 

mJ/cm²

 

A coating line may have good peak irradiance but still deliver insufficient accumulated energy if exposure time becomes too short.

 

Why Conveyor Speed Matters

 

Consider a UV coating line operating at a validated speed.

 

The coating cures correctly.

 

Production wants higher output, so conveyor speed is increased.

 

The UV LED power remains unchanged.

 

However:

 

Higher Conveyor Speed → Shorter Exposure Time

 

This can result in lower accumulated UV energy.

 

If the coating process was already operating close to its required curing threshold, the faster speed may cause quality problems.

 

Example: Coating Hardness Drops After Increasing Speed

 

A manufacturer applies a UV coating to plastic components.

 

At the original conveyor speed, the coating passes hardness and scratch-resistance tests.

 

The conveyor speed is increased by 20%.

 

Production output improves, but QA later finds that the coating scratches more easily.

 

Instead of immediately changing the coating formulation, the process engineer can compare:

 

Original UV energy

 

New UV energy

 

Peak irradiance

 

Exposure duration

 

Conveyor speed

 

If accumulated UV energy has dropped significantly, the curing process becomes an obvious area for investigation.

 

UV Energy and Coating Thickness

 

Coating thickness can also influence curing behaviour.

 

A process qualified for one coating thickness should not automatically be assumed suitable for a significantly different thickness.

 

If the coating application changes, manufacturers should consider re-evaluating:

 

UV exposure

 

Coating quality

 

Production speed

 

Material requirements

 

Measurement provides useful data during this process.

 

UV Energy and Adhesion

 

Poor adhesion can have many possible causes.

 

These include:

 

Surface contamination

 

Incorrect surface preparation

 

Substrate incompatibility

 

Coating formulation

 

Insufficient curing

 

If adhesion suddenly becomes worse, UV measurement can help determine whether curing conditions changed at the same time.

 

If UV measurements remain normal, attention can shift to other variables.

 

UV Energy and Scratch Resistance

 

A UV coating may appear dry but still have inadequate final properties.

 

If the curing reaction is incomplete, surface hardness or scratch resistance may be affected.

 

This is why visual inspection alone is not always sufficient.

 

A better process combines:

 

UV Measurement + Finished Product Testing

 

UV Energy and Gloss

 

Changes in coating appearance or gloss can have many causes, including material application and curing conditions.

 

A UV energy meter does not directly measure gloss.

 

However, recording UV conditions alongside gloss or appearance results can help determine whether changes in the curing process correlate with changes in finished-product appearance.

 

Designed for UV LED Curing

 

The Linshang LS137 is intended for UV LED light sources.

 

Its spectral response range is approximately:

 

340–420 nm

 

It is calibrated using a:

 

395 nm UV LED source

 

This makes it particularly relevant for industrial UV LED coating systems, especially those operating around 395 nm.

 

Common UV LED Wavelengths

 

Industrial UV LED coating equipment may use wavelengths such as:

 

365 nm

 

385 nm

 

395 nm

 

405 nm

 

The actual wavelength should be confirmed before purchasing a UV energy meter.

 

The detector's spectral response must be considered in relation to the curing source.

 

High-Intensity UV LED Measurement

 

Industrial UV LED coating systems can produce high irradiance.

 

The Linshang LS137 supports UV irradiance measurement up to:

 

40,000 mW/cm²

 

This makes it relevant to many high-intensity industrial UV LED curing applications within its specified operating conditions.

 

Working Distance Matters

 

The distance between the UV LED source and coated surface can affect the UV irradiance received by the product.

 

Working distance may change because of:

 

Different product height

 

Fixture changes

 

Conveyor modifications

 

UV module servicing

 

Mechanical adjustment

 

If the product position changes, UV exposure should be verified.

 

Example: Different Product Heights

 

Suppose one coating line handles two components.

 

Product A is relatively flat.

 

Product B is significantly taller.

 

Even when the machine uses the same UV power and conveyor speed, the surface of Product B may be at a different distance from the UV LED source.

 

Therefore, actual UV exposure may not be identical.

 

Measurement helps determine whether separate process settings are required.

 

Monitor UV LED Performance Over Time

 

UV LED systems offer long service life, but measured output should not automatically be assumed to remain exactly unchanged forever.

 

Periodic measurements can help track:

 

UV LED output

 

Optical contamination

 

Effects of maintenance

 

Process stability

 

A useful approach is:

 

New System → Baseline

 

Periodic Check → Compare

 

Change Detected → Investigate

 

Correct → Verify

 

Measure Before and After Cleaning

 

Coating environments may expose equipment to process contamination.

 

Where applicable, optical surfaces can be checked as part of maintenance.

 

A useful comparison is:

 

Measure Before Cleaning

 

then

 

Clean according to equipment manufacturer's instructions

 

then

 

Measure Again

 

A significant improvement may indicate that contamination was affecting UV transmission.

 

Measure After UV LED Replacement

 

After installing a new UV LED module, record the new curing condition.

 

Do not rely only on:

 

“The new lamp is working.”

 

Measure:

 

Peak UV irradiance

 

Accumulated UV energy

 

Exposure duration

 

Maximum temperature

 

Then verify coating quality.

 

This creates a new reference for future monitoring.

 

Establish a Known-Good Coating Baseline

 

When coating quality is excellent, record the process.

 

For example:

 

Product:

Coating:

Coating Thickness:

UV Wavelength:

UV Power Setting:

Conveyor Speed:

Working Distance:

Peak UV Irradiance:

Accumulated UV Energy:

Exposure Duration:

Maximum Temperature:

Hardness Result: PASS

Adhesion Result: PASS

Scratch Test: PASS

 

This becomes a powerful troubleshooting reference.

 

Compare Good and Bad Production

 

If coating quality changes later, repeat the measurements.

 

Compare:

 

Good Production

 

versus

 

Problem Production

 

Ask:

 

Did UV irradiance change?

 

Did accumulated energy change?

 

Did conveyor speed change?

 

Did exposure duration change?

 

Did working distance change?

 

Did temperature change?

 

This provides a systematic starting point for root-cause analysis.

 

What If UV Energy Is Lower?

 

Investigate:

 

UV LED condition

 

Conveyor speed

 

Optical contamination

 

Working distance

 

Cooling system

 

UV power setting

 

Active UV modules

 

Correct the identified issue and measure again.

 

What If UV Energy Is Normal?

 

If UV exposure remains consistent with the known-good baseline, investigate:

 

Coating formulation

 

Coating batch

 

Coating thickness

 

Substrate

 

Surface preparation

 

Material storage

 

Application process

 

This prevents unnecessary adjustment or replacement of a UV curing system that may be operating normally.

 

LS137 vs LS136 for UV Coating

 

The correct meter depends on the curing source.

 

UV LED Coating System

 

Consider:

 

Linshang LS137

 

Traditional High-Pressure Mercury UV Coating System

 

Consider:

 

Linshang LS136

 

Always identify the UV source technology before choosing the meter.

 

Who Can Use LS137 in a Coating Factory?

 

Potential users include:

 

Process Engineers

 

Production Engineers

 

QA Engineers

 

QC Technicians

 

Maintenance Engineers

 

Coating Line Supervisors

 

R&D Teams

 

Equipment Engineers

 

The LS137 can support both process development and ongoing production monitoring.

 

Applications

 

Potential applications include:

 

Plastic UV coating

 

Metal UV coating

 

Printed-product coating

 

Electronic-component coating

 

Industrial surface finishing

 

Packaging coating

 

Wood-product UV coating

 

Automated UV LED coating lines

 

Actual suitability depends on the UV source and process configuration.

 

Don't Control UV Coating by Machine Setting Alone

 

A machine may display:

 

UV Power = 80%

 

But quality control should ask:

 

What UV irradiance is actually reaching the product?

 

What accumulated UV energy is the coating receiving?

 

Is this still comparable with our validated production baseline?

 

That is a much stronger approach to process control.

 

A Better UV Coating Control Strategy

 

Instead of:

 

Set UV Power → Run Production → Inspect Rejects

 

consider:

 

Measure Good Process → Establish Baseline → Monitor UV Exposure → Compare with Quality Results → Detect Change → Correct → Verify

 

This can help manufacturers build a more consistent and measurable UV coating process.

 

Looking for a UV Energy Meter for UV Coating in Malaysia?

 

MTM Precision supplies industrial testing and measurement instruments for manufacturing, engineering, maintenance and quality-control applications in Malaysia.

 

If your company operates a UV LED coating line, provide us with:

 

UV wavelength

 

UV source type

 

Curing machine brand and model

 

Coating application

 

Conveyor speed

 

Expected UV intensity

 

We can assist you in determining whether the Linshang LS137 UV Energy Meter is suitable for your UV coating process.

 

Contact MTM Precision

 

MTM Precision Sdn. Bhd.

 

Showroom & Service Centre

 

No. 29-1 & 29-2, Jalan Bandar 18,

Pusat Bandar Puchong,

47160 Puchong, Selangor, Malaysia

 

🌐 Website: www.mtmpre.com.my

📧 Email: mtmpre@yahoo.com

📱 WhatsApp: +6016-660 7346

 

Contact MTM Precision for Linshang LS137 UV Energy Meter enquiries, UV coating applications, model selection, technical information and quotation in Malaysia.


 

13 Aug 2026