When Should You Replace a UV LED Curing Lamp? Check with Linshang LS137 Malaysia
When Should You Replace a UV LED Curing Lamp? Check with Linshang LS137 Malaysia
A UV LED curing machine begins producing inconsistent results.
The first reaction is often:
“The UV lamp is getting old. We should replace it.”
But is the UV LED module really the problem?
A replacement UV LED module can be expensive, and curing problems may also be caused by dirty optical surfaces, incorrect conveyor speed, changed working distance, cooling problems or production-material changes.
Before replacing the UV LED source, it is useful to measure its actual performance.
The Linshang LS137 UV Energy Meter can measure UV irradiance, accumulated UV energy and temperature, providing objective data that can help maintenance and production teams evaluate whether the curing system has actually changed.
Does a UV LED Lamp Need Regular Replacement?
Unlike traditional UV lamps, UV LED systems are known for long operating life.
However, this does not mean:
“Install once and never check again.”
UV LED output can change over time depending on:
Operating hours
LED operating temperature
Cooling efficiency
Driving conditions
Optical contamination
Equipment environment
Maintenance condition
The important point is that lamp age alone should not be the only reason for replacement.
Actual curing performance should also be considered.
The Lamp Is Still ON – Is It Still Good?
Not necessarily.
A UV LED source can continue producing visible light while its measured UV output differs from the original condition.
Looking at the lamp cannot tell you:
Actual UV irradiance
Peak UV irradiance
Accumulated UV energy
Change from the original baseline
For industrial curing, numerical measurement is much more useful than visual inspection.
What Does Linshang LS137 Measure?
The Linshang LS137 provides:
UV Energy
UV Irradiance
Peak UV Irradiance
Measurement Duration
Temperature
Maximum Temperature
These parameters can be compared with historical measurements from the same curing machine.
Start with a Baseline
The best way to determine whether a UV LED source has deteriorated is to know how it performed when it was healthy.
When a machine is:
New
Recently serviced
Fitted with a new UV LED module
Producing excellent curing results
record the UV conditions.
This becomes your known-good baseline.
What Should the Baseline Include?
Consider recording:
Machine ID:
UV wavelength:
UV LED operating hours:
UV power setting:
Conveyor speed:
Working distance:
Peak UV irradiance:
Accumulated UV energy:
Exposure duration:
Maximum temperature:
Product quality: PASS
Future measurements can then be compared against this record.
Don't Replace the Lamp Based Only on Operating Hours
Operating hours are useful maintenance information.
However, two UV LED systems with the same operating hours may not necessarily have identical conditions.
One machine may operate:
Continuously
At high power
In a hot environment
while another may operate:
Intermittently
At lower power
Under better thermal conditions
Therefore, operating hours should be considered together with measured performance and the equipment manufacturer's recommendations.
Sign 1 – Measured UV Output Has Declined
If repeated measurements under comparable conditions show a clear downward trend in UV output, the UV LED system should be investigated.
For example:
New Module → Baseline
Month 3 → Stable
Month 6 → Stable
Month 9 → Lower
Month 12 → Further reduction
This trend is more useful than discovering the problem only after production begins failing.
Sign 2 – Required UV Energy Can No Longer Be Achieved Reliably
Suppose a validated production process requires a certain UV exposure window.
Previously, the machine achieved it easily.
Now the machine struggles to maintain the qualified curing condition even after normal maintenance.
This may indicate that further technical investigation or UV LED replacement is required.
The final decision should consider:
UV measurements
Product quality
Equipment condition
Manufacturer recommendations
Sign 3 – Production Must Be Slowed Down to Maintain Curing
This can be an important warning sign.
Imagine a coating or printing line originally operates at:
40 m/min
Later, operators must reduce it to:
30 m/min
just to obtain acceptable curing.
Why?
One possibility is that slower speed provides longer exposure and compensates for reduced UV output.
If this occurs, measure the curing system.
Do not assume the problem is automatically the material.
Sign 4 – UV Power Must Constantly Be Increased
Another possible warning sign is that operators repeatedly increase UV power to maintain the same curing result.
For example:
Originally: 60%
then
70%
then
80%
then
100%
This does not automatically prove LED degradation, but it is a reason to investigate actual UV output and other process variables.
Sign 5 – UV Output Remains Low After Cleaning
Optical contamination can reduce the UV radiation reaching the product.
Before replacing the LED module, inspect and clean the relevant components according to the equipment manufacturer's procedure.
A useful comparison is:
Measure Before Cleaning
→ Clean
→ Measure After Cleaning
If UV output remains significantly below the historical baseline, further investigation may be justified.
Check Cooling Before Replacing the UV LED
UV LEDs rely on thermal management.
Depending on the equipment, cooling may involve:
Fans
Heat sinks
Air cooling
Water cooling
Chillers
A cooling-system problem can affect UV LED operating conditions.
Before blaming the UV LED module, check the cooling system according to the machine manufacturer's instructions.
Check Working Distance
Suppose the UV LED module was removed during maintenance and then reinstalled at a different height.
The UV source itself may be perfectly healthy.
But the changed geometry may produce a different irradiance at the product surface.
Before replacing the lamp, confirm:
UV module position
Product position
Working distance
Measurement position
Small setup changes can sometimes create large troubleshooting confusion.
Check Conveyor Speed
If accumulated UV energy is lower than before, determine whether conveyor speed changed.
Remember:
Faster Conveyor → Shorter Exposure
A perfectly healthy UV LED source can produce insufficient accumulated energy if the product moves through the curing zone too quickly.
Check Whether All UV Modules Are Operating
Some industrial curing machines use several UV LED modules.
If one module is:
Disabled
Operating at reduced power
Faulty
the total UV exposure can change.
Before replacing all UV LEDs, identify whether the issue is limited to one curing zone or module.
What If UV Measurements Are Normal?
This is important.
Suppose curing quality is poor, but current LS137 measurements remain comparable with the known-good baseline.
In this situation, investigate other variables such as:
UV ink
Coating
Adhesive
Substrate
Material thickness
Surface preparation
Material storage
Application thickness
Replacing a healthy UV LED module may not solve a material-related problem.
Example: Printing Company
A UV printing company notices that ink is becoming slightly tacky.
The UV LED module has operated for many hours.
The initial assumption is:
Replace the UV LED.
Before doing so, the maintenance team compares current UV measurements with historical baseline data.
If the UV output is still stable, the team can investigate ink, substrate and printing parameters instead.
Potentially, an unnecessary lamp replacement is avoided.
Example: UV Coating Factory
A coating line begins producing softer coatings.
Measurements show that UV energy is lower than before.
The team checks the system and discovers contamination on a relevant optical surface.
After proper cleaning:
UV energy returns close to the baseline.
The coating quality is verified again.
In this case, measurement helps identify a maintenance issue rather than immediately replacing the UV LED module.
Example: Electronics Manufacturing
An electronics manufacturer uses UV adhesive.
Bond strength begins becoming inconsistent.
UV measurements show a gradual decline compared with historical data even though:
Machine settings are unchanged
Working distance is unchanged
Optical surfaces are clean
Cooling is operating correctly
This gives engineers stronger evidence that the UV LED source itself may require further evaluation.
How Much UV Output Loss Is Acceptable?
There is no universal percentage that applies to every curing process.
Do not automatically use rules such as:
“Replace when output drops 10%.”
or
“Replace when output drops 20%.”
The acceptable limit depends on:
Ink
Coating
Adhesive
Substrate
Production speed
Process qualification
Equipment specification
Product-quality requirements
Each manufacturer should establish an acceptable process window based on its own production data.
The Goal Is Not Maximum UV Output
A UV LED does not necessarily need replacement simply because it no longer produces exactly the same output as when it was brand new.
The real question is:
Can the system still reliably produce the required validated curing conditions?
If yes, replacement may not yet be necessary.
If no, further maintenance or replacement may be justified.
LS137 Spectral Response
The Linshang LS137 is designed for UV LED curing systems.
Its spectral response range is approximately:
340–420 nm
and it is calibrated using a:
395 nm UV LED source
It is particularly relevant for industrial UV LED applications around commonly used curing wavelengths.
Common UV LED Wavelengths
UV LED curing equipment may use:
365 nm
385 nm
395 nm
405 nm
Always confirm the wavelength before selecting a UV measurement instrument.
For 395 nm UV LED systems, the LS137 is particularly relevant because its calibration is based on a 395 nm UV LED source.
High-Intensity UV LED Measurement
The Linshang LS137 supports UV irradiance measurement up to:
40,000 mW/cm²
This makes it suitable for many high-intensity industrial UV LED curing systems within its specified operating conditions.
A Better UV LED Replacement Decision
Instead of:
Curing Problem → UV Lamp Is Old → Replace Lamp
use:
Check Settings → Measure UV → Compare Baseline → Inspect Optics → Check Cooling → Check Distance → Check Speed → Correct → Measure Again → Decide
This can lead to better maintenance decisions.
Use Measurement After Replacement Too
If the UV LED module is eventually replaced, do not stop there.
Measure the new module.
Record:
Peak UV irradiance
UV energy
Exposure duration
Maximum temperature
Machine settings
This creates the next baseline.
The replacement process then becomes:
Old Module Measurement → Replace → New Module Measurement → Verify Product → Record Baseline
LS137 or LS136?
The correct instrument depends on the curing technology.
UV LED Curing System
Consider:
Linshang LS137
Traditional High-Pressure Mercury UV Curing System
Consider:
Linshang LS136
Do not select the instrument based only on the machine being described as a “UV curing machine.”
Identify the actual UV source.
Who Can Benefit from LS137?
Potential users include:
Maintenance Engineers
Production Engineers
Process Engineers
QA/QC Teams
Equipment Engineers
Printing Companies
UV Coating Manufacturers
Electronics Factories
UV Adhesive Users
The instrument can help these users make maintenance decisions using measured UV data.
Reduce Guesswork and Unnecessary Replacement
A UV LED module can be a significant equipment component.
Replacing it without evidence may add unnecessary maintenance cost.
At the same time, continuing to operate a curing system with inadequate UV output can create:
Rejects
Rework
Production delays
Customer complaints
The objective is therefore not to replace UV LEDs as early as possible or as late as possible.
The objective is to replace or service them when measurement and production requirements indicate that action is necessary.
Looking for Linshang LS137 in Malaysia?
MTM Precision supplies industrial testing and measurement instruments for manufacturing, engineering, maintenance and quality-control applications in Malaysia.
If you want to check whether your UV LED curing lamp is still performing correctly, provide us with:
UV wavelength
UV source type
Curing machine brand and model
Application
Expected UV intensity
Current curing problem
We can assist you in determining whether the Linshang LS137 UV Energy Meter is suitable for checking your UV LED curing system.
Contact MTM Precision
MTM Precision Sdn. Bhd.
Showroom & Service Centre
No. 29-1 & 29-2, Jalan Bandar 18,
Pusat Bandar Puchong,
47160 Puchong, Selangor, Malaysia
🌐 Website: www.mtmpre.com.my
📧 Email: mtmpre@yahoo.com
📱 WhatsApp: +6016-660 7346
Contact MTM Precision for Linshang LS137 UV Energy Meter enquiries, UV LED maintenance applications, technical information and quotation in Malaysia.
13 Aug 2026